Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 12 dokumen yang sesuai dengan query
cover
cover
Aisa Amanda
"Nanopartikel silika telah menarik perhatian karena sifat strukturnya yang sangat menguntungkan dan dapat diaplikasikan sebagai filler pada semen atau beton. Pada penelitian ini dilaporkan mengenai sintesis nanopartikel silika dengan metode sol-gel dan efek penambahannya sebagai aditif gas migration control pada oil and gas cement. Hasil karakterisasi nanopartikel silika menunjukkan bahwa nanopartikel tersebut memiliki bentuk spherical dan struktur yang amorf dengan distribusi ukuran partikel sebesar 49,73 nm. Hasil yang diperoleh dilakukan pengujian sifat fisik semen untuk mengetahui efek penambahan nanopartikel silika yang telah disintesis dan dibandingkan dengan nanopartikel silika komersil serta microsilica. Nanopartikel silika komersil dan microsilica memiliki ukuran partikel sebesar 16,65 nm dan 124,65 nm. Uji rheologi, uji thickening time, uji compressive strength serta uji permeabilitas gas dilakukan pada penelitian ini. Uji rheologi menunjukkan bahwa penambahan nanopartikel silika dan microsilica menyebabkan bubur semen semakin mengental serta meningkatkan nilai yield point. Uji thickening time menunjukkan bahwa dengan adanya penambahan nanopartikel silika ataupun microsilica diperlukan waktu sekitar 3-5 jam untuk mencapai batas konsistensinya, dimana bubur semen tidak dapat dipompa kembali. Uji compressive strength menunjukkan bahwa penambahan nanopartikel silika dapat meningkatkan daya tahan tekan pada semen dibandingkan dengan microsilica. Uji permeabilitas gas menunjukkan bahwa nanopartikel silika dan microsilica menunjukkan bahwa keduanya dapat secara efektif berperan sebagai filler pada pori-pori semen. Pengujian tersebut telah dilakukan untuk mengetahui apakah nanopartikel silika telah sesuai dengan kriteria sebagai aditif gas migration control.

Silica nanoparticles have attracted a lot of attention because of their highly beneficial structural properties and can be applied as fillers on cement or concrete. In this research we reported about the synthesis of silica nanoparticles with the sol-gel method and the effect of its addition as a gas migration control additive in oil and gas cement. The results of silica nanoparticles characterization shows that the morphology of nanoparticles is spherical and had an amorphous structure with particle size distribution of 49.73 nm. The results were tested for physical properties of cement to determine the effect of adding silica nanoparticles that had been synthesized, commercial silica nanoparticles and microsilica. Commercial silica nanoparticles and microsilica have particle sizes of 16.65 nm and 124.65 nm. Rheological test, thickening time test, compressive strength test and gas permeability test were observed in this research. Rheological tests shows that the addition of silica nanoparticles and microsilica caused the cement slurry getting thicker and increase the value of yield point. Thickening time test shows that it takes about 3-5 hours hours to reach the consistency limit with the addition of silica nanoparticles or microsilica, which the slurry cannot be pumped again. Compressive strength test shows that the addition of silica nanoparticles can increase the compressive strength value of cement compared to microsilica. The gas permeability test shows that silica nanoparticles and microsilica could effectively act as fillers in cement pores. All of the tests was conducted to determine whether silica nanoparticles were in accordance with the criteria as a gas migration control additive."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Siregar, Syawitri P
"Virus ebola salah satu virus yang dapat menyebabkan penyakit bersifat letal (mematikan) dan menyebabkan perdarahan (hemorrhagic). Penularannya dapat terjadi dari manusia ke manusia, hewan (nonhuman-primata) ke manusia. Angka kematian yang disebabkan oleh virus ebola dapat mencapai ribuan jiwa dengan spesies yang sangat berbahaya adalah Zaire ebolavirus dari lima spesies yang ada. Hingga saat ini baik antiviral maupun vaksin yang efektif bagi manusia belum ditemukan. Dalam penelitian ini toremifen sebagai senyawa modulator estrogen reseptor (MER) dipilih sebagai sumber database ligan. Database ligan menggunakan metode flexophor yang memperhitungkan titik farmakofor. Metode ini menghasilkan 16001 derivat toremifen, kemudian discreening menggunakan paramater RO5 untuk mendapatkan senyawa- senyawa yang bersifat druglikeness. Sebanyak 9876 senyawa derivat toremifen diperoleh dari proses screening. Hasil screening kemudian digenerate dengan metode farmakofor untuk mendapatkan hits ligan. Sejumlah 580 hits ligan diperoleh pada proses penentuan titik farmakofor. Kemudian simulasi docking dilakukan sebanyak tiga kali pada hits ligan. Simulasi docking diawali dengan rigid docking, dilanjutkan dengan rigid docking dengan retain yang berbeda. Tujuan pengulangan rigid docking ini adalah untuk memvalidasi hasil docking awal. Simulasi docking terakhir yang dilakukan adalah flexible docking. Sebanyak 576 ligan diperoleh dari tiga tahapan simulasi docking. Sebanyak 576 ligan ini diseleksi berdasarkan nilai ΔG binding , nilai RMSD lebih kecil dari 2. Dari 576 ligan tersebut dipilih 63 ligan dengan nilai RMSD lebih kecil dari 2, kemudian dipilih kembali tiga ligan sebagai kandidat potensial senyawa obat yaitu L579, L533 dan L194. Kandidat potensial senyawa obat ini dipilih berdasarkan ligan interaksi dan hasil farmakologi. Untuk pemilihan senyawa terbaik sebagai antiviral potensial dilakukan simulasi dinamik untuk melihat kestabilan senyawa tersebut. Berdasarkan nilai ΔG binding , RMSD, ligan interaksi, hasil farmakologi, dan simulasi dinamik disimpulkan bahwa ligan dengan kode L533 adalah ligan terbaik sebagai senyawa potensial antiviral ebola dengan nilai ΔG binding -10,4460 kcal/mol, RMSD 0.4697 Å. Hasil farmakologi juga menunjukkan bahwa L533 memiliki karakteristik yang baik sebagai antiviral.
Ebola virus is one of the virus that causes lethal disease and bleeding (hemorrhagic). Transmission can occur from human to human, animal (nonhuman primate) to humans. The number of deaths caused by viral ebola can reach thousands of lives with most dangerous species is Zaire ebolavirus from five existing species. Until now neither antiviral nor an effective vaccine for humans have been found. In this study toremifene as modulator estrogen receptor compound (MER) was selected as the source of ligand database. The ligand database uses the flexophore method that takes into account the pharmacophore point. This method produces 16001 toremifene derivatives, then screened using RO5 parameters to obtain druglikeness compounds. A total of 9876 toremifene derivative compounds were obtained from the screening process. The screening results are then generated by the pharmacophore method to obtain ligand hits. A total of 580 ligand hits were obtained at the farmakofore point determination process. Ligand hits are then simulated docking three times. The docking simulation begins with rigid docking. Rigid docking was applied twice with different retain. The purpose of this rigid docking repetition is to validate the initial docking results. The last docking simulation is flexible docking. A total of 576 ligands were obtained from three stages of docking simulation. As many as 576 ligands were selected based on ΔG binding , RMSD less than 2. From 576 ligands were selected 63 ligands with RMSD less than 2. For further step, three selected ligands were choosen. Three selected ligands as candidate of drug compound are L579, L533 and L194. These candidates were selected based on interaction ligand and pharmacological analysis. Dynamics simulation was done to see the stability of the compound for the selection of the best potential antiviral. The selection based on ΔG binding, RMSD, ligand interaction, pharmacology analysis and dynamics simulation. Finally, it was concluded that L533 was the best ligand as a potential antiviral with ΔG binding -10.4460 kcal/ mol, RMSD 0.4697 A. The pharmacological analysis also show that L533 has good characteristics as an antiviral."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2018
T50666
UI - Tesis Membership  Universitas Indonesia Library
cover
Mevricka Aurinda Garini
"Karbon dioksida merupakan salah satu gas utama yang menyebabkan emisi gas rumah kaca yang berada pada atmosfer. Dikarenakan sifatnya yang inert, CO2 sulit bereaksi dengan senyawa lain sehingga dibutuhkan suatu katalis. Pada penelitian ini digunakan zeolit ZSM-5 berpori hirarki bersumber mineral alam yaitu zeolit alam Bayat dan kaolin Bangka yang diimpregnasi bimetal NiZn sebagai katalis untuk mengkonversi CO2 dengan bantuan dari asetilena untuk menghasilkan asam akrilat. Zeolit ZSM-5 alam berpori hirarki disintesis menggunakan metode double template, dengan primary template TPAOH sebagai pengarah framework MFI serta secondary template PDDA-M sebagai pengarah struktur mesopori. Impregnasi logam bimetal nikel (Ni) dan seng (Zn) dengan metode co-impregnation lalu direduksi dengan aliran gas H2. Karakterisasi material ZSM-5 alam berpori hirarki dan NiZn/ZSM-5 alam berpori hirarki dilakukan dengan menggunakan FTIR, XRD, XRF, dan SEM-EDS. Analisis XRD menunjukkan kristalinitas dari ZSM-5 alam berpori hirarki berhasil disintesis. Analisis FTIR menunjukkan telah terjadinya dekomposisi template melalui kalsinasi. Pencitraan SEM menunjukkan morfologi material dengan bentuk coffin like-shaped yang merupakan ciri khas ZSM-5. Hasil analisisis EDS menunjukkan persen loading Ni dan Zn dalam ZSM-5 masing-masing sebesar 6,38% dan 3,23%. Reaksi karboksilasi asetilena dengan CO2 dilakukan dalam reaktor batch dengan variasi tekanan yaitu 1,5 bar, 2,5 bar, dan 3,5 bar. Produk hasil reaksi yang terbentuk dianalisis dengan HPLC. Dari hasil analisis HPLC diperoleh puncak pada waktu retensi 3,45 menit dengan kondisi optimum yaitu tekanan 2,5 bar, dan luas area sebesar 302,836 mAU. Sehingga, menunjukkan tidak adanya asam akrilat dalam produk.

Carbon dioxide is one of the main gases that cause greenhouse gas emissions in the atmosphere. Because of its inert in the atmosphere, the catalyst is needed to help CO2 react with other compounds. In this research, hierarchical ZSM-5 was prepared from natural minerals as sources, which is natural zeolite Bayat and Bangka kaolin then impregnated with bimetallic Ni-Zn as a catalyst to convert CO2 with support of acetylene to produce acrylic acid. Hierarchical zeolite ZSM-5 was synthesized using double template method, with TPAOH as its primary template that directed to MFI framework and PDDA-M as its secondary template that directed mesoporous structure. Impregnation of nickel (Ni) and zinc (Zn) bimetallic was conducted by co-impregnation method followed by reduction H2 gas flow. Material characterization of natural ZSM-5 hierarchy and NiZn/ZSM-5 hierarchy were conducted FTIR, XRD, XRF, and SEM-EDS. FTIR analysis shows that there has been a decomposition of templates through calcination. XRD analysis showed that the crystallinity of the ZSM-5 hierarchy was synthesized successfully. SEM analysis shows the morphology of the material with the coffin like-shaped which is characteristic of the ZSM-5. The EDS analysis shows percent loading of Ni and Zn in ZSM-5 are 6.38% and 3.23%. The acetylene carboxylation reaction with CO2 was carried out in a batch reactor with pressure variations 1.5 bar, 2.5 bar, and 3.5 bar. The products formed were analyzed by HPLC and GCMS. HPLC analysis shows a new peak at a retention time of 3,625 minutes. The optimum condition was obtained at 2.5 bar and the value is 302.836 mAU. So, it shows do not contain acrylic acid in the product."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Andrian Surya Wirawan
"Limbah minyak yang mencemari perairan dapat bercampur dengan limbah rumah tangga seperti deterjen membentuk emulsi yang stabil. Pada penelitian ini akan dilakukan demulsifikasi dan adsorpsi solar dari model limbah emulsi solar dalam air menggunakan adsorben zeolit admisel polistirena. Kondisi optimum pembuatan model limbah emulsi solar dalam air yang stabil adalah konsentrasi surfaktan SDS 0,02 M sebanyak 20 mL ditambah minyak solar 0,05 mL; waktu pengadukan 15 menit; dan kecepatan pengadukan 450 rpm. Kestabilan emulsi ditentukan dengan turbidimeter didapatkan nilai turbiditas 413 NTU. Ukuran partikel ditentukan dengan Particle Size Analyzer (PSA) didapatkan ukuran partikel yang seragam sebesar 372,6 nm. Pembuatan adsorben diawali dengan pembentukan admisel, yaitu pembentukan lapisan bilayer pada permukaan zeolit dengan konsentrasi HDTMA-Br 70 mmol/L. Selanjutnya mengadsolubilisasi stirena yang ditentukan dengan menggunakan UV-Visible spectrophotometry, didapatkan konsentrasi optimum sebesar 1,6 x 10-3 M. Terakhir dilakukan polimerisasi dengan menggunakan inisiator Kalium Persulfat (K2S2O8). Adsorben zeolit admisel-polistirena digunakan untuk demulsifikasi dan adsorpsi solar dari emulsi solar dalam air. Kondisi optimum untuk adsorpsiDS- adalah pada dosis adsorben 0,4 gram, waktu pengadukan 40 menit dengan pH 6,5 dengan DS- teradsorpsi sebesar 0,04986 mg/gram. Kondisi optimum adsorpsi solar adalah dosis adsorben 0,4 gram, waktu pengadukan 30 menit dan pH 6,5 dengan solar teradsorpsi sebesar 79 mg/gram adsorben.

Water pollution is a very serious problem, especially in Indonesia. One of kind waste disposed by oil industry is diesel oil. Waste oil that contaminates water is normally with household waste such as detergents produced stable emulsion. Demulsification is the process of separating two liquid phases are homogeneously mixed with each other to form an emulsion. This research studied the adsorption of waste oils and detergents that form emulsions by using polystyrene adsolubilized in admicelle HDTMA zeolite. First, a stable emulsion sample of waste oil was prepared by mixing diesel oil and detergent, namely Sodium Dodecyl Sulfate (SDS) surfactant with some of variations: variation of the surfactant concentration, variations in the volume of diesel oil, stirring time variation, and variation of stirring speed of the emulsion. Turbidity values of the most stable emulsion was 413 NTU with a particle size of 372.6 nm homogenously. Then, modified zeolite using the styrene polymer adsolubilized into admicelle HDTMA. The optimum value of the styrene adsolubilized using UV -Visible spectrofotometry is at 1.6 x 10-3 M. Zeolite has been modified styrene polymers can adsorb and demulsificate oil waste and detergent. Then do a wide variety of applications to demulsification and adsorption process, including variations in adsorbent dose, stirring time, and pH. The optimum value of adsorbent dose on the adsorption variation of diesel oil and surfactant SDS is 0,4 grams, stirring time of 30 minutes with a pH value of 6,5 obtained for the solar adsorption at 79 mg/g adsorbent, while for the adsorbed surfactant SDS at 0.04986 mg/g of adsorbent.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2014
S54394
UI - Skripsi Membership  Universitas Indonesia Library
cover
Millati Hanifah Saprudin
"Melimpahnya gas CO2 di alam berpotensi untuk digunakan sebagai bahan baku konversi recovery untuk menghasilkan produk bahan kimia sintetik salah satunya melalui reduksi CO2 secara elektrokimia elektroreduksi. Elektroda boron-doped diamond BDD diketahui memiliki berbagai karakteristik unggul untuk digunakan sebagai elektroda kerja pada aplikasi elektroreduksi. Pada penelitian ini akan dilakukan modifikasi elektroda BDD dengan mendepositkan bimetal platinum dan iridium Pt-Ir menggunakan metode wet chemical seeding yang dilanjutkan dengan elektrodeposisi pada potensial -0,5 V vs Ag/AgCl selama 15 menit. Optimalisasi dilakukan pada variasi rasio Pt-Ir 1:1, 1:2 dan 2:1. Setiap elektroda dikarakterisasi menggunakan CV, SEM, EDX, XPS dan Raman Spektroskopi. Elektroreduksi CO2 dilakukan pada sel 2 kompartemen, yaitu ruang katoda yang berisi NaCl 0,1 M dan terta terlarut gas CO2 dan ruang anoda yang berisi Na2SO4 dengan menggunakan setiap elektroda tersebut masing-masing pada potensial -1,1 V, -1,2 V, -1,3 V, -1,5 V, dan -1,7 V vs Ag/AgCl selama 60 menit. Produk hasil reduksi dianalisa menggunakan HPLC dan GC. Produk terbanyak yang dihasilkan adalah asam format sebesar 7,08 mg/L dengan efisiensi faraday 23,17 menggunakan elektroda PtIr 2:1 BDD pada potensial -1,1 V vs Ag/AgCl. Selain asam format dihasilkan pula produk lainnya seperti metanol, gas CO, gas metana dan gas H2. Sedangkan dengan menggunakan elektroda Pt-BDD hanya mampu menghasilkan asam format 2,51 mg/L pada potensial -1,6 V vs Ag/AgCl. Keberadaan Ir mampu menurunkan potensial pada elektroreduksi CO2 untuk menghasilkan produk dengan konsentrasi yang lebih besar.

The abundance of CO2 gas in nature potentially to produce valueable chemical products through electrochemical reduction of CO2 electroreduction of CO2. Boron doped diamond BDD is known to have superior characteristic to supports to electroreduction CO2 which requires high potensial reduction. In this research, BDD electrode was modified by depositing platinum iridium bimetals onto BDD surface through wet chemical seeding method followed by electrodeposition at 0,5 V vs Ag AgCl for 15 min. Optimization was also performed for various Pt Ir mole ratios, including 1 1 , 1 2 and 2 1. Each electrode was characterized by using CV, SEM, EDX, XPS and Raman spectroscopy. Electroreduction of CO2 was performed by using two compartement cell. In the cathode chamber 0.1 M NaCl with dissolved CO2 gas was placed, while in the anode chamber the solution was 0.1 M Na2SO4. PtIr BDD were performed as working electrode. Electroreduction of CO2 was carried out at various potentials of 1,1 V, 1,2 V, 1,3 V, 1,5 V, and 1,7 V vs Ag AgCl for 60 min. The products of the electroreduction were analyzed using HPLC and GC. The main product in this system was formic acid with the largest concentration of 7,08 mg L with 23,17 farradaic efficiency at PtIr 2 1 BDD at the potential of 1,1 V vs Ag AgCl. Other products including methanol, CO, methane and H2 gas was also generated. On the other hand, Pt BDD electrode can produce 2,51 mg L formic acid at much higher potential at 1,6 V vs Ag AgCl. The existance of Ir particles proposed to contribute in reducing the required potential and to produce concentration of formic acid the CO2 reduction."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Aritonang, Rani Puspitasari
"Karbon dioksida merupakan gas rumah kaca yang konsentrasinya terus meningkat setiap tahunnya. Salah satu upaya untuk mengatasinya yaitu dengan mengonversi CO2 menjadi turunan hidrokarbon yang lebih bernilai melalui proses elektrokimia. Penggunaan elektroda boron-doped diamond BDD dilaporkan menampilkan performa yang baik pada elektroreduksi CO2. Namun BDD memiliki kekurangan yaitu aktivitas katalitiknya yang rendah. Sehingga dibutuhkan cara untuk meningkatkan aktivitas katalitik BDD, diantaranya yaitu modifikasi dengan logam. Penelitian ini menggunakan BDD termodifikasi tembaga dan nikel sebagai elektroda kerja pada reduksi CO2. Modifikasi BDD dilakukan melalui teknik seeding, dan elektrodeposisi yang dilanjutkan dengan pemanasan pada suhu 7000C dalam atmosfer N2. Karakterisasi dengan SEM-EDX pada elektroda BDD termodifikasi tembaga dan nikel menunjukkan kestabilan yang baik setelah dilakukan pemanasan. Selanjutnya performa reduksi CO2 elektroda CuNi-BDD dibandingkan dengan Cu-BDD dan Ni-BDD. Pada potensial -1,2 V, Ni-BDD memberikan hasil efisiensi Faraday yang tinggi dibanding CuNi-BDD dan Cu-BDD. Produk yang terbentuk pada reduksi CO2 pada potensial -1,2 V yaitu CO, CH4 pada CuNi-BDD, asam format pada Cu-BDD, sedangkan pada Ni-BDD dihasilkan asam format dan metanol disamping gas CO dan CH4. Namun pada potensial yang lebih negatif -1,5 V , CuNi-BDD memberikan performa yang paling baik di antara elektroda lain. CuNi-BDD membentuk produk yang lebih beragam dibanding Cu-BDD maupun Ni-BDD.

Carbon dioxide is one of greenhouse gases whose increasing concentration annually. One of the way to overcome it by converting CO2 gas into bulk chemicals electrochemically. Recently, BDD is used as working electrode for CO2 reduction because it has good performance for CO2 reduction. But, BDD has low catalytic activity. So it is needed to modify BDD to increase it's catalytic activity, such as by modifying BDD surface BDD with metal. In this study, we used copper nickel modified BDD as working electrode for CO2 reduction. The method used to modify BDD were seeding, continued with electrodeposition and annealing at 7000C in N2 atmosphere. SEM EDX pictures of the modified electrode showed good stability after annealing treatment. CuNi BDD electrode was compared with monometal modified BDD. When potential applied at 1,2 V, Ni BDD produced the highest faradaic efficiency than CuNi BDD and Cu BDD. The CO2 reduction at potential 1,2V produced several products such as CO, CH4 for CuNi BDD, formic acid for Cu BDD, as for Ni BDD can produce formic acid and methanol beside CO and CH4. But when more negative potential applied 1,5 V , CuNi BDD performed the best to reduce CO2. The product produce from CuNi BDD at 1,5V are more varies than Cu BDD or Ni BDD. "
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Lia Trisnawati
"ABSTRAK
Pada penelitian ini, nanokomposit selulosa-Fe3O4 telah berhasil disintesis dengan memodifikasi Fe3O4 ke permukaan nanoselulosa yang telah dihidrolisis oleh asam asetat anhidrat. Selulosa yang digunakan pada penelitian ini berasal dari isolasi sekam padi. Isolasi selulosa dari sekam padi menghasilkan rendemen rata-rata sebesar 47,34 . Hasil sintesis yang diperoleh dikarakterisasi dengan menggunakan instrumentasi FT-IR, XRD, SEM dan TEM. Selanjutnya nanokomposit selulosa-Fe3O4 diaplikasikan sebagai katalis untuk sintesis metil ester dari waste cooking oil. Kondisi optimum yang diperoleh untuk sintesis metil ester dari waste cooking oil yaitu pada suhu 60oC selama 120 menit dengan komposisi katalis nanokomposit selulosa-Fe3O4 sebesar 0,09 g. Hasil yield konversi metil ester yang diperoleh sebesar 78.

ABSTRACT
In this research, cellulose Fe3O4 nanocomposite has been successfully synthesized by modifying Fe3O4 onto nanocellulose rsquo s surface that has been hydrolyzed by anhydrous acetate. Cellulose used in this research was isolated from rice husk. Cellulose isolated from rice husk had a yield of 47.34 . The synthesis products were characterized using FT IR, XRD, SEM and TEM. Then, cellulose Fe3O4 nanocomposite was applied as a catalyst for methyl ester synthesis from waste cooking oil. The optimal condition for methyl ester synthesis from waste cooking oil was at 60 oC for 120 minutes with composition of cellulose Fe3O4 nanocomposite catalyst of 0.09 g. The conversion yield of methyl ester was 78."
2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Budi Setiawan
"ABSTRAK
Penggunaan berbagai produk titanium selalu mengalami peningkatan dari tahun ke tahun. Produk titanium yang paling sering digunakan adalah TiO2 sebagai pigmen warna putih dalam industri cat, industri makanan dan industri kosmetik. Indonesia mansih mengimpor berbagai produk titanium. Padahal di Indonesia banyak terdapat mineral ilmenite yang merupakan sumber utama titanium yang terdapat di alam. Penelitian ini dilakukan untuk mendapatkan TiO2 anatase dari Ilmenite Bangka. Residu kaya titanium didapatkan dari hasil leaching ilmenite Bangka dengan larutan asam klorida untuk melarutkan besi pada ilmenite. Data EDX menunjukkan bahwa kandungan besi berkurang pada residu hasil leaching. Digunakan H2O2 10% sebagai agen pengkoordinasi untuk meleaching titanium dari residu menjadi garam ammonium perokso titanat. Padatan perokso titanat didapatkan dengan memanaskan larutan garam ammonium perokso titanat. Data XRD menunjukkan terbentuknya TiO2 anatase setelah mengkalsinasi padatan tersebut pada suhu 600oC. Data EDX juga menunjukkan bahwa masih terdapat pengotor-pengotor seperti silikon (0,98%) dan besi (2,75%) pada TiO2 anatase yang didapatkan. Berbagai karakterisasi dilakukan pada TiO2 anatase seperti uv-vis spektroskopi, scanning electron microscopy dan UV Diffuse Reflectance Spectroscopy. TiO2 anatase dari ilmenite ini mempunyai nilai celah energi 3,08 eV. Uji fotokatalis dilakukan terhadap zat warna CongoRed dan dibandingkan dengan TiO2 komersial degussa P25. Persen degradasi oleh TiO2 anatase dari ilmenite ini sekitar 20%, sedangkan persen degradasi oleh degussa P25 mencapai nilai 92%.

ABSTRACT
The use of titanium products have been increasing from year to year. TiO2 is one of titanium products which is often used as a white pigment in paint, food industry and cosmetics industries. Until now, Indonesia is stil importing various product of titanium even though Indonesia has many ilmenite source which are naturally the main source of titanium. This research was conducted to obtain TiO2 anatase from Bangka ilmenite. The hydrolyzed titania residue was prepared from Bangka ilmenite leached by hydrochloric acid solution to dissolve the iron in ilmenite. EDX data show that the iron content was reduced in hydrolyzed titania residue. The H2O2 (10%) was used as a coordination agent to leach titanium from the hydrolyzed titania residue to obtain ammonium perokso titanate. Peroxo titanate powder was obtained by evaporating the ammonium perokso titanate solution. XRD data show that TiO2 anatase was formed after calcining peroxo titanate powder at the temperature of 600oC. EDX data also show the anatase TiO2 obtained in this research had the impurities, such as silicon (0,98%) and iron (2,75%). Various studies such as X-ray diffraction, UV-vis spectroscopy, Scanning Electron Microscopy and UV Diffuse Reflectance Spectroscopy were conducted. The band gap of anatase TiO2 from extracted ilmenite is 3,08 eV. Photoreactivity was conducted againts the CongoRed dye and compared with the commercial TiO2, Degussa P-25. The degradation percentage of TiO2 from extracted ilmenite is 20% whereas degradation percentage of Degussa P25 is 92%."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2012
S43637
UI - Skripsi Open  Universitas Indonesia Library
cover
Syah Reza
"ABSTRAK
Proses adsorpsi pada bentonit tapanuli yang termodifikasi surfaktan kationik
terhadap senyawa organik paraklorofenol telah dilakukan. Dilakukan fraksinasi
terlebih dahulu untuk mendapat kandungan montmorillonit terbanyak, kemudian
dilakukan preparasi Na-MMT (Natrium Montmorillonit), dan penentuan Kapasitas
Tukar Kation (KTK) memberikan nilai sebesar 62,5 meq/gram. Surfaktan yang
digunakan ialah surfaktan kationik ODTMABr (Oktadesil Trimetil Ammonium
Bromida) yang memiliki 18 rantai alkil. Surfaktan ini digunakan sebanyak 1 KTK
sebagai interkalan dalam preparasi organoclay. Analisis dengan menggunakan XRD
menunjukkan basal spacing dari OCT (Organoclay Tapanuli) mengalami peningkatan
yang cukup besar (21,04) dibandingkan dengan Na-MMT (14,33) dan montmorillonit
(15,69). Hal ini membuktikan bahwa surfaktan kationik telah masuk ke dalam
montmorillonit. Hasil uji aplikasi OCT sebagai adsorben senyawa organik para
klorofenol (p-C6H4Cl(OH)) menunjukkan bahwa organoclay lebih baik daya
adsorpsinya dibandingkan dengan bentonit alam. Saat p-klorofenol memiliki
konsentrasi sebesar 50 ppm, OCT mampu menyerap senyawa tersebut sebesar 36,4
ppm dan belum menunjukkan kondisi optimum. Di sisi lain, bentonit alam telah
mencapai optimum saat konsentrasi awal 10 ppm. Pola isoterm adsorpsi dari OCT
menunjukkan pola isoterm adsorpsi Freundlich pada konsentrasi besar namun pada
konsentrasi kecil pola yang ditunjukkan adalah pola isoterm adsorpsi Langmuir.

ABSTRACT
Adsorption on tapanuli bentonite modified by cationic surfactant has been done.
The fractionation of bentonite has been done in order to get the highest contain of
montmorillonite, then it was done the preparation of Na-MMT (Sodium
Montmorillonite), and the result of cation exchange capacity (CEC) is 62,5 meq/gram.
In this research, ODTMABr (Octadecyl Trimethyl Ammonium Bromide) which has
18 alkyl chains, was used as cationic surfactant. 1 CEC of surfactant was used as
intercalant agent in organoclay preparation. XRD analysis showed the basal spacing of
OCT increased significantly (21,04) when compared with Na-MMT (14,33) and
Montmorillonite (15,69). This result proved that cationic surfactant has been
intercalated into montmorillonite. The application of OCT as adsorbent of pchlorophenol(
p-C6H4Cl(OH)) showed that OCT is better than raw material bentonite.
When the concentration of p-chlorophenol was 50 ppm, OCT could adsorp its
compound in 36,4 ppm and has not reached the optimum condition, whereas raw
material benonite has the optimum condition in10 ppm. The adsorption isoterm of
OCT showed Freundlich adsorption isoterm rules in high concentration while in low
concentration the rules was followed Langmuir adsorption isoterm.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2012
S43705
UI - Skripsi Open  Universitas Indonesia Library
<<   1 2   >>