Hasil Pencarian  ::  Simpan CSV :: Kembali

"Pada pengecoran Besi Tuang Dinding Tipis terjadi fenomena unik, yaitu terbentuknya lapisan kulit. Lapisan tersebut menjadi pusat stress konsentrasi untuk terjadinya retak material. Salah satu cara untuk meminimalisir terbentuknya lapisan kulit adalah menjaga kecepatan pendinginan pada keadaan optimum. Penelitian ini dilakukan untuk mengetahui pengaruh ketebalan isolator glasswool terhadap kecepatan pendinginan dalam pembentukan lapisan kulit. Variasi modifikasi cetakan yang digunakan adalah tanpa isolator (P4M1), isolator glasswool tebal 40mm sebelah kiri benda dan 50mm sebelah kanan benda(P5M1), dan isolator ketebalan 50mm dikedua sisi benda(P7M1). Dilakukan karakterisasi metalografi non etsa dan etsa, uji mekanis berupa uji tarik, dan uji kecepatan pendinginan pada plat urutan ketiga masing-masing benda cor. Hasil menunjukkan bahwa adanya pengaruh ketebalan isolator terhadap kecepatan pendinginan benda cor. Kecepatan pendinginan tertinggi hingga terendah adalah 21,59⁰C/menit, 3,75⁰C/menit, dan 3,61⁰C/menit. Lapisan kulit ketebalan rata-rata yang didapat P7M1 324μm, P4M1 105μm dan P5M1 71μm. Jumlah nodul tertinggi hingga terendah P4M1 1121 nodul/mm2, P7M1 916 nodul/mm2, dan P5M1 801 nodul/mm2. Nodularitas yang didapat P4M1 78%, P5M1 75% dan P7M1 64%. Nilai tensile strength yang didapat dengan nilai 287MPa, 288MPa sampai 383 MPa. Matriks yang didapat adalah full ferit.

---

Thin wall ductile iron has unique phenomena in manufacturing called skin effect. Skin effect becomes stress concentration to form crack initiation. One of many methods to decrease skin effect is providing optimum cooling rate. This research used the influence of glasswool isolator thickness leading to different cooling rate as variable. Variation of casting also investigated which are molding without isolator (P4M1), molding using isolator glasswool with thickness 40mm on the left side and 50mm on the left side of plate (P5M1) and the last is molding using isolator glaswool with 50mm on both of sides (P7M1). Samples were characterized using metallograpy technique (etching and non etching), mechanical testing especially tensile test and cooling rate testing.

The result shows that thickness of isolator glasswool has influences on cooling rate. The cooling rate varies from fastest to slowest which are 21,59⁰C/minutes, 3,75⁰C/minutes, and 3,61⁰C/minutes. The skin thickness is produced from the thickest to thinnest on the mold using 50mm thickness glaswool isolator, the mold without glasswool isolator and the mold using 40mm glasswool isolator on left side and 50mm glasswool isolator on the right side. High nodul counting resulted from the mold without isolator, the mold using 50mm glasswool isolator and the mold using 40mm glasswool isolator on left side and 50mm glasswool isolator on the right side. Highest nodularity was produced on the mold without isolator which is 78%, the mold using isolator glasswool 40mm and 50mm thickness produced 75% nodularity dan the mold using glasswool isolator 50mm produced 64% nodularity. Tensile test showed tensile strength alter from 287MPa, 288MPa until 383 MPa. The matrix obtains full ferritic"

"Penggunaan energi yang tidak terbarukan seperti minyak bumi dan batu bara secara perlahan telah membawa dunia ini ke dalam krisis energi, sehingga diperlukan upaya penghematan energi. Isu dunia mengenai penghematan energi tersebut sangat berkaitan erat dengan industri otomotif. Industri otomotif dituntut untuk menghasilkan produk dengan emisi kendaraan yang rendah dan kendaraan yang hemat bahan bakar. Material TWDI (thin wall ductile iron) yang dapat dilakukan pemrosesan lanjut menjadi TWADI (thin wall austempered ductile iron) menjadi kandidat yang paling menarik karena sifat mekanisnya yang baik serta biaya yang lebih murah jika dibandingkan dengan aluminium. Tantangan yang dihadapi pada proses pembuatan material TWDI saat ini yaitu kecenderungan terbentuknya lapisan kulit (skin effect) pada permukaan logam hasil pengecoran yang dapat menurunkan sifat mekanis.Penelitian ini dilakukan untuk mendapatkan pengaruh penggunaan isolator berupa glasswool, kayu, dan rockwool dengan ketebalan 40 mm terhadap kecepatan pendinginan. Pengujian yang dilakukan adalah pengujian komposisi kimia, pengamatan makro, pengamatan struktur mikro, dan pengujian tarik. Pengamatan struktur mikro dilakukan secara kualitatif dan kuantitatif, dengan bantuan program image analysis. Sedangkan analisis kecepatan pendinginan didapatkan secara kualitatif.Hasil dari penelitian ini diketahui bahwa kecepatan pendinginan merupakan fungsi dari jumlah nodul, karbida, nodularitas, dan diameter rata-rata nodul. Kecepatan pendinginan tercepat hingga terlambat yaitu pada penggunaan isolator rockwool (P9M1), kayu (P8M1), dan glasswool (P6M1). Untuk ketebalan lapisan kulit rata-rata terbesar hingga terkecil yaitu P8M1 32,58 μm, P9M1 25,59 μm, dan P6M1 25,45 μm. Dari karakteristik nodul, P8M1 memiliki nodularitas tertinggi sebesar 81% lalu diikuti P6M1 sebesar 79% dan P9M1 sebesar 76%. P6M1 memiliki 1605 nodul/mm2, P9M1 1274 nodul/mm2 dan P8M1 1141 nodul/mm2. Sedangkan, diameter nodul P6M1 10,20 μm, P8M1 9,71 μm, dan P9M1 9,09 μm. Matriks yang didapatkan adalah ferit dan karbida dengan tingkat keparahan karbida tertinggi hingga terendah yaitu P9M1, P8M1, dan P6M1. Nilai kekuatan tarik P6M1 367 MPa, P9M1 329 MPa, dan P8M1 146 MPa. Sedangkan elongasi P6M1 2%, P9M1 1,1%, dan P8M1 1%. Sifat mekanis yang didapatkan masih berada di bawah nilai standar.

---

Nowadays, the use of unsustainable energy such as petroleum and coal subsequently has brought us to the energy crisis. So that the effort of saving energy is crucial. World issues regarding energy savings is very closely related to the automotive industry. The automotive industry is required to produce products with lower emissions and fuel-efficient vehicles. TWDI (thin wall ductile iron) which can be processed to TWADI (thin wall austemperd ductile iron) became the best candidate due to good mechanical properties and lower cost comparing to aluminum. The challenge confronted in the process of TWDI making is the tendency of skin formation on the surface of the metal casting reduced its mechanical properties.

This research is conducted to obtain the effect of insulators utilization such as glasswool, wood, and rockwool with the thickness of 40 mm towards the cooling rate. Methods performed are chemical composition, visual observation, microstructure observation, and tensile testing. While, microstructure observation is conducted qualitatively and quantitatively using image analysis program, the analysis of the cooling rate is obtained qualitatively.

The cooling rate, from the fastest to the slowest, is rockwool (P9M1), wood (P8M1), and glasswool (P6M1). Where as, for the average skin thickness, from the biggest to the smallest, is P8M1 32.58 μm, P9M1 25.59 μm, and P6M1 25.45 μm. For nodule characteristics, P8M1 has the 81% nodularity and then followed by P6M1 with 79% and P9M1 with 76%. While, P6M1 has 1605 nodule/mm2, P9M1 and P8M1 has 1274 and 1141 nodul/mm2, respectively. While, the biggest nodule diameter is P6M1 with 10.20 μm, the next is P8M1 with 9.71 μm and then P9M1 with 9.09 μm. Ferrite and carbide is found in the matrix. The severity level of carbide, from the highest to the lowest, is P9M1, P8M1 and P6M1. From mechanical aspects, the highest ultimate tensile strength is obtained by P6M1 with 367 MPa, then followed by P9M1 with 329 MPa and P8M1 with 146 MPa. Where as, for the elongation, P6M1 is 2%, P9M1 is 1.1% and P8M1 is 1%. The mechanical properties obtained don't fulfill the standardfollowed by P6M1 with 79 and P9M1 with 76 While P6M1 has 1605 nodule mm2 P9M1 and P8M1 has 1274 and 1141 nodul mm2 respectively While the biggest nodule diameter is P6M1 with 10 20 m the next is P8M1 with 9 71 m and then P9M1 with 9 09 m Ferrite and carbide is found in the matrix The severity level of carbide from the highest to the lowest is P9M1 P8M1 and P6M1 From mechanical aspects the highest ultimate tensile strength is obtained by P6M1 with 367 MPa then followed by P9M1 with 329 MPa and P8M1 with 146 MPa Where as for the elongation P6M1 is 2 P9M1 is 1 1 and P8M1 is 1 The mechanical properties obtained don rsquo t fulfill the standard."

"Kebutuhan penghematan energi dunia menuntut untuk melakukan peminimalisasian energi tak terlepas di bidang pengecoran. Penggunaan TWADI (Thin Wall Austempered Ductile Iron) yang didapatkan dari heat treatment TWDI (Thin Wall Ductile Iron) menjadi kandidat yang paling menarik karena ketangguhannya yang sangat tinggi serta biaya lebih murah dan tentunya lebih hemat energi dibandingkan aluminium. Dalam Pemrosesan TWDI menemui masalah yaitu perubahan grafit nodul menjadi flakes atau yang dikenal sebagai skin effect dimana skin akan menurunkan sifat mekanis dari TWDI. Penelitian ini mempelajari pengaruh penambahan kadar nodulizer terhadap terbentuknya skin serta pengaruhnya terhadap sifat mekanis. Skin yang didapat pada penambahan 1,1 % nodulizer dengan tebal 40 µm lebih tipis dibandingkan 1 % nodulizer yang memiliki tebal skin 45 µm. Nilai UTS yang didapat oleh penambahan 1,1% nodulizer yaitu 416,5 MPa, lebih tinggi dibandingkan 1 % nodulizer sebesar 387,54 MPa, dimana hal tersebut sejalan dengan nodularitas yang lebih tinggi dengan penambahan 1,1 % nodulizer. Nilai elongasi kedua sampel tidak mencapai 10 % yang dikarenakan terbentuknya kolumnar karbida yang terbentuk dari berlebihnya kadar mangan pada kedua sampel.

---

Recent world energy condition obligates people to reduce quantity of energy useement especially ini casting process. Uses of Thin Wall Austempered Ductile Iron (TWADI), which is a heat treatment material from Thin Wall Ductile Iron (TWDI) , become a best candidate to replace aluminium in industry due to the fact of its high quality toughness and another mechanical properties, with low producing cost and also low energy production. One of the most issue that have been met in processing TWDI is a phenomenon that nodular graphites turn into flakes shape which will decrease large amount of mechanical properties.

This research is studying about the enhacement of content nodulizer for reducing skin thickness and also to increase mechanical properties. The addition of 1,1 % nodulizer that obtained shown an effective result with reducing 11 % thickness of skin compared to the thickness of addition 1 % nodulizer. The thickness of skin with addition 1,1% nodulizer is 40 µm, while with addition 1 % nodulizer is 45 µm. The UTS number that has been reached by 1,1 % nodulizer is 416,5 % MPa, which is bigger than the UTS of 1 % nodulizer in the amount of 387,54 MPa which also as a result of grater nodularity of 1,1 % nodulizer. The elongation of both sample have elongation below 10 %, as result of carbides that have been formed in the microstructure, because of excessive number of manganese."

"Komoditas utama di sektor pertanian Indonesia adalah padi, yang juga merupakan tanaman pokok di negeri ini sehingga limbah yang dihasilkan juga akan sangat banyak. Untuk mengatasi hal seperti ini, maka pengolahan limbah sekam padi kerap dilakukan. Sekam padi mengandung 50% selulosa, 25 ?30 % lignin, dan 15 ?20 % silika. Kandungan silika ini yang nantinya akan berharga setelah diolah lebih lanjut, setelah dilakukan pemanggangan sempurna sekam padi mengandung sekitar 90%-98% silika.Pada penelitian ini pengolahan sekam padi dilakukan dengan metode pelindian pada larutan HCl 1 M selama 3 jam, kemudian di recovery dan dilanjutkan pemanggangan dengan variasi laju temperaturnya 3C/min., 5C/min., dan 7C/min. hingga 650C dan ditahan selama 4 jam. Hasil penelitian didapatkan dengan variasi laju temperaturnya 3C/min., 5C/min., dan 7C/min silika dengan kadar 99,170%, 99,038%, dan 98,966%. Proses pelindian dan pemanggangan akan menghilangkan komponen-komponen organik dan logam pengotor-pengotor di dalamnya, dan apabila diamati morfologinya, sekam padi yang telah diberi perlakuan strukturnya akan lebih halus dan berporos.

---

The main commodities in the agricultural sector of Indonesia is rice, which is also a staple crop in this country so that the waste generated will also be very much. To cope with this kind of thing, then the rice husk waste treatment is often done. Rice husks contain 50% cellulose, 25% lignin -30 and 15 -20% silica. The silica content of which will be valuable when processed further, after perfect roasting rice husk contains about 90% -98% silica.

In this study, rice husk processing is done by the method of leaching in 1 M HCl solution for 3 hours, then recovered and continued roasting by the temperature rate variation of 30C/min., 50C/min., and 70C/min until reaching 6500C and held for 4 h. Research results obtained by varying the temperature rate of 30C/min., 50C/min., and 70C/min with silica content of 99.170%, 99.038% and 98.966%. Leaching and roasting process will eliminate the components of organic and metallic impurities in it, and if the morphology was observed, rice husk which has been treated to be more delicate and highly porous structure."