Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 32 dokumen yang sesuai dengan query
cover
Tomy Abuzairi
Abstrak :

ABSTRACT
Tungsten oxide, has many interesting optical, electrical, structural, and chemical properties, are an ideal choice material for electrochromic smart windows devices. In this study, tungsten oxide thin films were prepared by the thermal oxidization on Tungsten/ITO/glass substrates at different heat-treatment temperatures. The optimum heat-treatment temperature, corresponding to the maximum electrochromic performance, was achieved by 550 oC. X-ray diffraction (XRD) analysis indicates that a tetragonal WO3 phase formed at temperatures below 550 oC and the phase transformed to monoclinic W18O49 after the temperature was raised to 650 oC. The electrical properties analysis confirmed that the highest electrical conductivity show the superior electrochromic performance, with the maximum coloration efficiency value of 60.4 cm2/C. The tetragonal WO3 films, with heat-treatment temperature 550 oC and 450 oC, exhibit good electrochromic properties such as a high diffusion coefficient (1.7x10-11 cm2/s), fast electrochromic response time (coloration time 1.6 s, bleaching time 1.2 s), and high coloration efficiency (60.4 cm2/C). Furthermore, tungsten oxide nanowires were prepared on a tungsten film (W)/ITO-glass substrate at 500 oC for electrochromic devices using the heat-treatment technique. The electrical properties analysis confirmed that the highest electrical conductivity achieve the superior electrochromic performance with the maximum coloration efficiency value. The tungsten oxide nanowires shows excellent electrochromic properties such as a higher diffusion coefficient (2x10-9 cm2/s), faster electrochromic response time (coloration time 1.7 s, bleaching time 1.1 s), and higher coloration efficiency (67.41 cm2/C) than other tungsten oxide films without nanowires. Therefore, the tungsten oxides nanowire prepared by heat-treatment technique, corresponding to the maximum electrochromic performance, would be further adopted in the commercial application of smart windows.
Fakultas Teknik Universitas Indonesia, 2012
T30157
UI - Tesis Open  Universitas Indonesia Library
cover
Khotimatul Fauziah
Abstrak :
Tunnel Field Effect Transistor (TFET) merupakan struktur divais yang menggunakan mekanisme transport band-to-band tunneling untuk proses injeksi carrier. Hal ini berbeda dengan MOSFET yang menggunakan thermionic emission untuk mengalirkan arus. Dengan mekanisme transport yang berbeda ini,TFET dapat mencapai nilai subthreshold swing (SS) lebih rendah dari 60 mV/dec, lebih kecil dari transistor konvensional. Rendahnya nilai SS ini penting untuk penskalaan tegangan dengan arus switching yang ideal. Pada tesis ini dilakukan analisa karakteristik tunnel FET pada divais Si lateral p-n dan p-i-n berskala nanodari data hasil penelitian yang diperoleh Nano Device Laboratory, Research Institute of Electronics, Shizuoka University, Jepang. Fenomena band-to-band tunneling pada divais lateral p-n dan p-i-n berskala nano berhasil diobservasi. Band-to-band tunneling terjadi pada saat divais diberikan tegangan reverse bias dan gate diberikan tegangan positif. Dari hasil analisa pada struktur p-n dengan ketebalan oxide 150 nm, diperoleh SS mencapai 647,5 mV/dec. Dengan metode komparasi tegangan substrat pada ketebalan oxide 3 nm diperoleh SS sebesar 12,95 mV/dec, lebih kecil dari 60 mV/dec yang merupakan batasan nilai SS yang dapat dicapai pada MOSFET. Selanjutnya dilakukan analisa pengaruh co-doped dan intrinsic region terhadap tegangan threshold dan pengaruh panjangnya terhadap SS. Diperoleh bahwa struktur p-n memiliki tegangan threshold lebih tinggi dibanding struktur p-i-n. Hal ini dipengaruhi oleh level Fermi pada channel region, di mana co-doped region memiliki level Fermi EF = 0,112 eV, lebih rendah dari i-region dengan EF = 0,56 eV, sehingga dibutuhkan tegangan gate yang lebih besar untuk menurunkan energi band channel sehingga terbentuk tunnel junction. Dengan mengubah panjang co-doped dan i-region diperoleh hasil bahwa pada struktur p-n dengan panjang co-doped 250 nm diperoleh SS sebesar 647,5 mV/dec, lebih kecil dari struktur dengan panjang co-doped 1000 nm dengan SS mencapai 724 mV/dec. Hal ini disebabkan pada struktur p-n, co-doped region yang lebih pendek akan membentuk channel region yang lebih sempit sehingga elektron pada channel akan lebih cepat tersapu menuju drain. Sebaliknya, pada struktur p-i-n dengan panjang i-region 2000 nm diperoleh SS 704 mV/dec, lebih kecil dari struktur dengan panjang i-region 1000 nm dengan SS mencapai 776 mV/dec. Hal ini dapat dijelaskan bahwa pada struktur p-i-n, semakin panjang i-region maka daerah deplesi pada channel semakin lebar sehingga tunnel region yang terbentuk akan lebih panjang dan probabilitas elektron yang dapat dilewatkan pada tunnel region semakin besar. ...... Tunnel Field Effect Transistor (TFET) is a device structure which use band to band tunneling transport for the carrier injection mechanism, unlike MOSFET which use thermionic emission. This transport mechanism enables TFET to reach sub threshold swing (SS) less than 60 mV/dec that can enable voltage scaling with ideal current switching. Analysis of the characteristic of tunnel FET on Si nanoscale lateral p-n and p-i-n devices will be conducted in this thesis based on the research data at Nano Device Laboratory, Research Institute of Electronics, Shizuoka University, Japan. Band to band tunneling phenomenon on the lateral nanoscale lateral p-n and p-i-n devices are successfully observed. Band to band tunneling occurs when the devices are in reverse biased condition and positive voltage is applied to the gate. For p-n device with the oxide thickness 150 nm, the SS reaches 647,5 mV/dec. Using substrate voltage comparison methods on the oxide layer with thickness of 3 nm, the SS value is 12,95-mV/dec, smaller than 60 mV/dec as a limitation of SS on MOSFET. Next, we analyze the effect of codoped and intrinsic region to the threshold voltage and its length to the subthreshold swing (SS). We found that, p-n devices have higher threshold voltage compared to p-i-n devices. We ascribe that this results come from the fact that codoped region has lower Fermi level than that in i-region. By varying the intrinsic and the co-doped region length, we observed that p-n device with co-doped length 250 nm has SS 647,5 mV/dec, smaller than p-n device with co-doped length 1000 nm which has SS 724 mV/dec. We consider that when the co-doped region length is decreasing, the channel region will be shorter. Therefore the electron on the the conduction band of the channel will be swept out to the drain region quickly. We also found that, p-i-n device with i-region length 2000 nm has SS 704 mV/dec, smaller than p-i-n device with i-region length 1000 nm with SS 776 mV/dec. We ascribe that when the i-region length is increasing, the tunnel region in the channel region will be larger, such that the probabilities of electron to tunnel to the channel region increases.
Depok: Fakultas Teknik Universitas Indonesia, 2014
T38976
UI - Tesis Membership  Universitas Indonesia Library
cover
Jormin Husada
Abstrak :
ABSTRAK
Single Electron Transistor (SET) merupakan salah satu alternatif pengganti teknologi CMOS karena ukuran divais dan konsumsi daya yang kecil. Pada skripsi ini dilakukan rancang bangun gerbang logika dasar seperti gerbang logika AND, OR, NAND, NOR, dan NOT yang dibangun dengan SET menggunakan perangkat lunak SIMON 2.0. Gerbang logika dasar berbasis SET yang telah dirancang akan dibandingkan dengan gerbang logika dasar berbasis CMOS. Hasil simulasi dengan perangkat lunak SIMON 2.0 menunjukkan bahwa gerbang logika dasar berbasis SET memiliki karakteristik hasil keluaran yang sama dengan gerbang logika dasar berbasis CMOS. Dengan membandingkan ukuran divais dan konsumsi daya antara teknologi CMOS dengan SET didapatkan bahwa struktur SET memiliki luas divais 78 kali lebih kecil dari luas divais teknologi 22-nm CMOS dan konsumsi daya yang seribu kali lebih kecil dari konsumsi daya pada teknologi 32-nm CMOS.
ABSTRACT
Single Electron Transistors (SETs) are considered as the attractive candidates to replace CMOS technology due to their ultra-small size and low power consumption. This thesis presents a design and construction of basic logic gates, such as AND, OR, NAND, NOR, and NOT logic gates, based on Single Electron Transistor (SET) using SIMON 2.0 as the simulator. The simulation result shows that the output of the basic logic gates based on SET has the same output characteristic as the output in CMOS technology. We also analyze and compare the dimension and power consumption of the basic logic gates based on CMOS and SET. SET has 78 times smaller device area than 22-nm CMOS technology and a thousand times smaller power consumption than 32-nm CMOS technology.
Fakultas Teknik Universitas Indonesia, 2015
S57740
UI - Skripsi Membership  Universitas Indonesia Library
cover
Niki Fadhliyah
Abstrak :
ABSTRAK
Single Electron Transistor (SET) merupakan sebuah transistor yang memanfaatkan pergerakan satu buah elektron. Salah satu aplikasi dari single elektron transistor adalah single electron memory. Pada skripsi ini, dilakukan desain memori berbasis floating dot dan difokuskan pada analisa pergerakan elektron dalam divais SEM dengan mengatur kapasitansi pada tunnel junction antara quantum dot dan floating dot. Dengan adanya elektron pada quantum dot akan mengubah level energi dari floating dot. Fenomena hysterisis diperoleh pada rentang kapasitansi antar dot C12 = 9.999 x 10-17 – 1 x 10-19 F. Efek kapasitansi antar dot juga dapat menyebabkan terjadinya fenomena elektron berpindah antar dot dengan cepat pada rentang kapasitansi antar dotnya C12 = 10-18 - 10-16 F.
ABSTRACT
Single Electron Transistor (SET) is a very sensitive device which has capability to detect single electron. One of SET’s application is a single electron memory (SEM). We design SEM based on floating dot and we analyze the impact of capacitance variation of tunnel junction between quantum dot and floating dot about the electron transfer in SEM device. The presence of electron in quantum dot will affect energy level of floating dot. The hysterisis phenomena which is one of SEM’s phenomena is obtained in the range capacitance C12 = 9.999 x 10-17 – 1 x 10-19 F. The effect of capacitance between quantum dot and floating dot occured at C12 = 10-18 - 10-16 F.
Fakultas Teknik Universitas Indonesia, 2015
S58687
UI - Skripsi Membership  Universitas Indonesia Library
cover
Sandia Rini
Abstrak :
Organic Light Emitting Diode (OLED) merupakan LED dimana lapisan emissive nya terbuat dari bahan organik yang dapat memancarkan cahaya ketika dialiri arus listrik. Dalam skripsi ini, dirancang struktur green OLED dengan empat struktur yang berbeda yaitu single layer green OLED (GPE), HTL+GPE, GPE+ETL, dan HTL+GPE+ETL. Hasil simulasi menunjukkan bahwa penambahan electron transport layer dapat meningkatkan nilai luminansi secara signifikan. Penambahan HTL dan ETL dapat menurunkan operating voltage. Luminansi tertinggi yaitu 997.330 cd/m2 dicapai ketika tegangan 4V pada struktur ITO/HTL/GPE/ETL/LiF-Al. Warna yang dihasilkan dari keempat struktur tersebut adalah warna hijau dengan panjang gelombang 550 nm.
An OLED (Organic Light Emitting Diode) is a LED in which the emissive electroluminescent layer is a film of organic compounds which emit light in response to an electric current. This thesis presents a design green OLED structure with four different structures, single layer green OLED (GPE), HTL+GPE, GPE+ETL and HTL+GPE+ETL. The simulation result shows that addition of electron transport layer will significantly improve the luminance. The addition of HTL and ETL can reduce the operating voltage. The highest luminance is 997.330 cd/m2 achieved when the voltage is 4V on the structure of ITO/HTL/GPE/ETL/LiF-Al. The color of all the structures is green with a wavelength of 550 nm.
Depok: Fakultas Teknik Universitas Indonesia, 2015
S59444
UI - Skripsi Membership  Universitas Indonesia Library
cover
Yefa Sister
Abstrak :
White Organic Light Emitting Diode (WOLED) merupakan teknologi baru dari divais solid state yang dikembangkan untuk memenuhi kebutuhan divais pencahayaan dan display. Salah satu cara untuk membuat WOLED yaitu dengan menggunakan struktur hybrid multi emissive layer. Pada skripsi ini dibuat desain dan simulasi menggunakan struktur hybrid WOLED yang terdiri dari material red phosphorescent emitter, green phosphorescent emitter dan blue fluorescent emitter sebagai emissive layer pada perangkat lunak SimOLED 4.5.0. Tegangan dan ketebalan material emissive layer divariasikan untuk mendapatkan OLED warna putih. White OLED berhasil diperoleh dengan menambahkan electron blocking material yang diletakkan antara green phosphorescent emitter dan blue fluorescent emitter dan mencapai hasil optimal pada saat diberikan tegangan 2-10 Volt dengan ketebalan green phosphorescent emitter 2-4 nm. Pada setiap tegangan yang dapat menghasilkan White OLED, ketebalan red phosphorescent emitter yang diperlukan mulai dari 10 nm sementara ketebalan optimal untuk blue fluorescent emitter dan EBM adalah 6-21 nm. Semakin tebal sebuah emissive layer maka semakin dominan warna yang dihasilkan pada layer ini karena semakin banyak rekombinasi yang terjadi pada emissive layer tersebut. ...... White Organic Light Emitting Diode (WOLED) is a new technology of solid state devices which is developed to fulfill the demand for lighting devices and displays. One approach to make WOLED uses hybrid multi emissive layer structure. In this thesis we designed and simulated a hybrid WOLED using red phosphorescent emitter, green phosphorescent emitter and blue fluorescent emitter as emissive layer on SimOLED 4.5.0 software. Voltage and material thickness is var ied to obtain white OLED. WOLED can be achieved by using an electron blocking material between green phosphorescent emitter and blue fluorescent emitter and reach optimal result on 2-10 Volt with the thickness of green phosphorescent emitter is 2-4 nm. Each voltage that produce white OLED, need a thickness of red phosphorescent emitter start from 10 nm and the effective thickness of blue fluorescent emitter and EBM are 6-21 nm. When the thickness of an emissive layer increases, the dominant light color is emitted at this layer because the number of recombination increase at that layer.
Depok: Fakultas Teknik Universitas Indonesia, 2015
S59504
UI - Skripsi Membership  Universitas Indonesia Library
cover
Juandri Andhyka Putra
Abstrak :
Single Emissive Organic Light Emitting Diode (OLED) merupakan divais diodapenghasil cahaya yang terdiri dari emissive layer yang diapit oleh 2 konduktoryakni anoda dan katoda. OLED dibuat dengan proses fabrikasi yang direalisasikandengan berbagai tahapan, pada skripsi ini dilakukan tahapan fabrikasi. Ketikalaminasi dilakukan, temperatur laminasi menjadi masalah dalam proses fabrikasiyang menentukan berhasil atau tidaknya fabrikasi divais dioda. Pada skripsi inidilakukan fabrikasi OLED struktur ITO/PFO/Al dengan temperatur laminasi yangberbeda-beda. Setelah fabrikasi, dilakukan pengujian karakteristik I-V dari divaisOLED. Hasil pengujian karakteristik I-V menunjukkan bahwa laminasi optimalterjadi pada temperatur 160 C. ......Single Emissive Organic Light Emitting Diode OLED is a diode device composedof emissive layer sandwiched by 2 conductors that are anode and cathode. OLED ismade by fabrication process that is realized by many steps, in this paper laminationstep was performed. While lamination, the lamination temperature become one ofthe problems in fabrication process that decided the diode fabrication is success ornot. In this paper OLED with ITO PFO Al structure was fabricated with differentlamination temperature. Then, I V characteristic of OLED device was tested. TheI V characteristic test result show that the optimum lamination is at temperature160 C.
Depok: Fakultas Teknik Universitas Indonesia, 2017
S69469
UI - Skripsi Membership  Universitas Indonesia Library
cover
Falah Al Abrori
Abstrak :
Organic Light Emitting Diode OLED adalah sebuah divais electroluminance yang menggunakan bahan organik sebagai emissive layer. Dalam fabrikasi OLED terdapat berbagai macam cara untuk menumbuhkan emissive layer dengan ketebalan tertentu. Salah satu tekniknya adalah dengan cara spincoating. Kecepatan rotasi spincoating menentukan ketebalan dari lapisan yang ditumbuhkan. Ketebalan lapisan tersebut mempengaruhi performa divais yang dihasilkan. Dalam skripsi ini OLED dengan struktur ITO/ Polylfluorene PFO /Al difabrikasi menggunakan teknik laminasi dan menggunakan spincoating untuk menumbuhkan lapisan PFO. Variasi dilakukan terhadap kecepatan rotasi spincoating pada 1000 rpm, 2000 rpm, 3000 rpm, 4000 rpm, dan 5000 rpm. Hasil fabrikasi menunjukkan karakteristik arus dan tegangan yang dihasilkan sesuai dengan karakteristik OLED. Kecepatan rotasi spincoating yang optimum adalah 3000 rpm. Divais 3000 rpm, 4000 rpm, dan 5000 rpm dapat menghasilkan luminasi berwarna kebiru-biruan. ......Organic Light Emitting Diode OLED is an electroluminance device that uses organic material as an emissive layer. In OLED fabrication there are various ways to grow an emissive layer with a certain thickness. One of the techniques is by spincoating. The rotation speed of spincoating determines the thickness of the grown layer. The thickness of the layer affects the performance of the resulting device. In this thesis OLED with the structure of ITO Polylfluorene PFO Al is fabricated using lamination technique and using spincoating to grow PFO. Variations were made to spincoating rotation speeds at 1000 rpm, 2000 rpm, 3000 rpm, 4000 rpm, and 5000 rpm. The fabrication results show the current characteristics and OLED voltage. The optimum rotational speed of spincoating at 3000 rpm. The device has the smallest treshold voltage. The 3000 rpm, 4000 rpm, and 5000 rpm devices can produce bluish luminations.
Depok: Fakultas Teknik Universitas Indonesia, 2017
S67626
UI - Skripsi Membership  Universitas Indonesia Library
cover
Layina Maulana
Abstrak :
Organic Light-Emitting Diode OLED merupakan LED yang memiliki lapisan organik pada bagian emisifnya untuk memancarkan cahaya ketika dialiri arus listrik. Meskipun teknologi pencahayaan dan display OLED sudah berkembang, efisiensi OLED secara umum masih rendah sehingga dibutuhkan penelitian dan eksperimen yang dapat meningkatkan performa OLED baik dari segi struktur maupun materialnya. Skripsi ini akan membahas pengaruh jenis material anoda dan katoda terhadap efisiensi daya melalui proses simulasi dengan software SimOLED 4.5.1. Struktur yang disimulasikan adalah single emissive layer OLED dengan Alq3 sebagai material organiknya. Selain itu, juga akan dilakukan proses fabrikasi menggunakan teknik laminasi dan spin-coat. Fabrikasi bertujuan untuk menganalisis material katoda yang menghasilkan karakterisasi I-V paling optimal. Hasil dari simulasi pada SimOLED membuktikan bahwa kombinasi material PEDOT:PSS dan alumunium Al memiliki nilai efisiensi daya sebesar 1000 kali lebih tinggi dibanding struktur referensi ITO ndash; Lif-Al . Kemudian pada proses fabrikasi, material katoda yang menghasilkan performa paling baik adalah Al dengan PFO sebagai lapisan emisif dan ITO sebagai anoda. Hasil OLED yang difabrikasi menghasilkan arus tertinggi sebesar 2 10-8 A pada 10 Volt. ......Organic Light Emitting Diode OLED is an LED that has an organic layer on its emissive layer to emit light when electrified. Although OLED lighting and display technologies have evolved, OLED efficiency is generally low. Therefore, research and experiments are required so that OLED performance can be improved from both its structure and material. This thesis will discuss the effect of anode and cathode material on power efficiency through simulation process using SimOLED 4.5.1 software. The simulated structure is a single emissive layer OLED with Alq3 as its organic material. In addition, fabrication process will also be done using lamination and spin coat techniques. Fabrication aims to analyze the cathode material that produces the most optimum I V characterization. Simulation results show that the combination of PEDOT PSS and aluminum as the electrode material has a power efficiency value of 1000 times higher than reference structure which is ITO and Lif Al. Then in the fabrication process, the cathode material that produces the best performance is aluminum, with PFO as emissive material and ITO as anode. OLED results in fabrication has a maximum current of 2 10 8 at 10 Volts.
Depok: Fakultas Teknik Universitas Indonesia, 2017
S68850
UI - Skripsi Membership  Universitas Indonesia Library
cover
Bahtiar Syahroni
Abstrak :
Energi listrik menjadi energi yang paling sering digunakan karena proses pembangkitannya yang mudah, dapat dikonversi menjadi bentuk energi lain serta dapat dengan mudah disimpan. Salah satu metode penyimpanan energi listrik yang paling terkenal saat ini adalah baterai. Baterai memiliki keunikan selain dapat menyimpan energi, baterai juga dapat menghasilkan energi melalui proses kimia di dalamnya. Dalam pemilihan baterai ada beberapa faktor yang perlu disesuaikan dengan spesifikasi desain yaitu harga, usia, berat, volume, temperatur, sensitivitas dan akses pemeliharaan. Ada 2 tipe baterai yang biasa digunakan yaitu lithium ion dan lead acid. lithium ion memiliki spesifikasi lebih baik dari pada lead acid, namun dengan biaya yang lebih mahal. Lead acid cocok digunakan untuk aplikasi permanen on site dan aplikasi yang tidak mementingkan effiensi. Baterai memerlukan sistem kontrol supaya mampu bekerja dengan baik dan handal yang disebut (Battery Management System) BMS. Salah satu aspek BMS adalah pemantauan (State of Charge) SOC. Salah satu metode estimasi SOC adalah internal resistance. Penelitian dimulai dengan mengidentifikasi faktor yang mempengaruhi State of Charge, membuat desain rangkaian, simulasi rangkaian. realisasi printed circuit board hasil simulasi, pengukuran tegangan dan arus dan validasi hasil pengukuran dengan membandingkannya dengan hasil pengukuran dari modul NI 9206......Electrical energy is the energy that is most often used because the generation process is easy, can be converted into other energy and can be stored easily. One of the most popular methods of storing electrical energy today is the battery. Batteries are unique in addition to being able to store energy, batteries can also produce energy through chemical processes in them. In selecting a battery there are several factors that need to be adjusted to the design specifications, namely price, age, weight, volume, temperature, sensitivity and access to maintenance. There are 2 types of batteries commonly used, namely lithium ion and lead acid. lithium ion has better specifications than lead acid, but at a higher cost. Lead acid is suitable for permanent on-site and non-efficiency applications. Batteries require a control system to be able to work properly and reliably called (Battery Management System) BMS. One aspect of BMS is (State of Charge) SOC Supervision. One method of estimating SOC is internal resistance. The research begins by identifying the factors that affect the State of Charge, making circuit designs, circuit simulations. realization of printed circuit board simulation results, measurement of voltage and current and validation of measurement results by comparing them with measurement results from INI 9206 module.
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4   >>