Hasil Pencarian

Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 6 dokumen yang sesuai dengan query
cover
Muhammad Farhan
"

Lapisan anodik yang ditumbuhkan pada paduan AA7075 dengan metode hard anodizing tidak seragam karena lambatnya reaksi oksidasi pada presipitat. Dalam penelitian ini, pengaruh penambahan Etilen Glikol (EG) sebagai zat aditif pada elektrolit dalam proses hard anodizing pada logam paduan AA7075 diteliti melalui karakterisasi morfologi, sifat mekanik dan sifat korosi lapisan anodizing yang dihasilkan. Uji korosi metode elektrokimia pada larutan 3% NaCl + 1% HCl. Senyawa EG dipilih karena umum digunakan sebagai zat antibeku pada industri logam dan memiliki sifat inhibitor korosi dalam sistem pendingin. Penambahan EG pada elektrolit meningkatkan laju reaksi oksidasi dari presipitat yang terdapat pada substrat, sehingga menghasilkan struktur lapisan yang lebih seragam di sepanjang antarmuka oksida-logam. Namun konsumsi energi pada reaksi oksidasi presipitat menyebabkan berkurangnya oksidasi pada matrix aluminium sehingga lapisan yang dihasilkan menjadi lebih tipis. Selain itu, pelepasan gas oksigen yang terjadi selama proses oksidasi presipitat terjebak dalam lapisan membentuk pori sehingga kekerasan menurun dari 196,2 HV menjadi 117,8; 115,2; dan 107,7 HV masing-masing dengan penambahan 10, 20, dan 30 % EG. Ketahanan korosi lapisan anodik menjadi 30 mV lebih tinggi, nilai potensial korosi menjadi 10 mV lebih positif, arus korosi menjadi 80 µA/cm2 lebih rendah, dan nilai resistansi polarisasi naik 100 Ω lebih tinggi dengan penambahan 10% EG sedangkan pada konsentrasi EG yang lebih tinggi menurunkan ketahanan korosi lapisan. EG yang optimum untuk menghasilkan lapisan dengan sifat mekanik dan ketahanan korosi yang baik adalah 10%. Lapisan anodik yang mengandung EG sensitif terhadap hydrothermal sealing.

 


The anodic layer grown on AA7075 alloy with the hard-anodizing method is not uniform because of the slow oxidation reaction at precipitate. In this study, the effect of adding Ethylene Glycol (EG) as an additive to electrolytes in the process of hard anodizing on alloy metals AA7075 was examined through morphological characterization, mechanical properties and corrosion properties of the anodizing layer produced. Electrochemical method corrosion test on a 3% NaCl + 1% HCl solution. EG compounds are chosen because they are commonly used as antifreeze substances in the metal industry and have corrosion inhibitor properties in the cooling system. The addition of EG to electrolytes increases the rate of oxidation reactions from the precipitates found on the substrate, resulting in a more uniform layer structure along the metal-oxide interface. However, energy consumption in precipitate oxidation reactions leads to reduced oxidation in the aluminum matrix so that the resulting layer becomes thinner. In addition, the release of oxygen gas that occurs during the oxidation process of the precipitate is trapped in the pore-forming layer so that the hardness decreases from 196.2 HV to 117.8; 115.2; and 107.7 HV each with the addition of 10, 20 and 30% EG. The corrosion resistance of the anodic layer is 30 mV higher, the corrosion potential value is 10 mV more positive, the corrosion current is 80 µA/cm2 lower, and the polarization resistance value rises 100 Ω higher with the addition of 10% EG whereas at the higher EG concentration reduce coating corrosion resistance. The optimum EG for producing layers with good mechanical properties and corrosion resistance is 10%. Anodic layer containing EG is sensitive to hydrothermal sealing

"
Lengkap +
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Nabila Ramadhanti
"ABSTRAK
Kelemahan material implan Ti-6Al-4V adalah bersifat ­bio-inert, sehingga tidak mendukung reaksi jaringan/sel tubuh dengan implan. Penelitian ini bertujuan meningkatkan tendensi pelekatan sel osteoblas pada permukaan implan Ti-6Al-4V melalui modifikasi biokompatibilitas dengan meningkatkan kekasaran permukaan sehingga sel di sekitar implan berkembang. Menggunakan metode anodisasi maka dapat mendukung pula tujuan coloring implan guna memudahkan identifikasi implan ketika pemasangan. Sebelum anodisasi, sampel dipreparasi hingga permukaanya mirror like dan bersih dari kotoran lemak. Anodisasi menggunakan elektrolit H2SO4 0.5 M dan 1 M, pada variasi tegangan 30 V, 50 V, dan 70 V selama 5 menit. Pengaruh tegangan dan konsentrasi elektrolit terhadap kekasaran permukaan diidentifikasi melalui pengujian Surfcom, pengamatan morfologi dan karakterisasi unsur di permukaan dan cross section lapisan TiO2 dengan SEM-EDS, dan kekuatan penempelan lapisan oksida diuji dengan uji ketahanan gores dan diamati dengan OM. Hasil penelitian menunjukkan bahwa semakin tinggi tegangan maka lapisan oksida warna semakin tebal dengan kekasaran permukaan dan ketahanan gores yang lebih tinggi, sehingga hasilnya menunjukkan bahwa kekerasan lapisan oksida meningkat. Fitur kekasaran permukaan didapatkan dari tekstur berupa lembah dan puncak dengan adanya mikropori TiO2 yang terbentuk karena reaksi evolusi oksigen dan inkorporasi ion sulfat dari elektrolit, sehingga biokompatibilitas implan meningkat dengan mekanisme mechanical interlocking antara implan dengan jaringan/sel osteoblas.

ABSTRACT
Ti-6Al-4V implants are bio-inert, it doesnt support tissues or cells reaction with implants. This study was aimed to increase the tendency of attaching osteoblasts to the surface of implants through biocompatibility modification by increased surface roughness, also to get colored implants to facilitate identification of implants when the implants going to be installed, by anodization method. The sample was prepared until had mirror-like surfaces and cleaned from dirt. Anodization used 0.5 M and 1 M H2SO4 electrolytes, 30 V, 50 V, and 70 V for 5 minutes. The effect of voltage and electrolyte concentration on surface roughness was identified through Surfcom, morphological and elemental characterization with SEM-EDS, and the attachment strength of the oxide layer tested by scratch resistance test and observed with OM. The results indicated that the higher the voltage, the color oxide layer gets thicker with higher surface roughness and scratch resistance, so those results indicated that the oxide layers hardness increased. Surface roughness features was obtained by texture of valleys and peaks with TiO2 micropores caused by oxygen evolution reactions and incorporation of sulfate ions from electrolytes, so that implants biocompatibility can be increased by mechanical interlocking mechanism between implants and osteoblast bone cells / tissue."
Lengkap +
2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Hendri Mahmudin
"Korosi atmosferik merupakan hasil interaksi logam dengan atmosfer di sekitarnya, yang terjadi akibat kelembaban dan oksigen di udara dan diperparah dengan adanya polutan seperti gas dan garam yang terkandung di udara. Pantai atau laut adalah daerah yang paling korosif, karena atmosfemya mengandung partikel klorida yang bersifat agresif dan mempercepat laju korosi. Salah satu metode yang efektif untuk mencegah dan mengeadalikan korosi adalah dengan proses anodisasi. Anodisasi adalah proses untuk membuat lapisan oksida tipis berpori pada permukaan logam. Lapisan tersebut memiliki sifat tahan terhadap cuaca dan lebih keras dari logam dasarnya. Dalam penelitian ini digunakan logam aluminium teknis berbentuk lembaran. Daya tahan logam aluminium terhadap kondisi cuaca berbanding lurus dengan ketebalannya. Untuk mencapai tujuan tersebut maka dilakukanlah penelitian terhadap parameter proses seperti jenis larutan, temperatur, konsentrasi dan variasi waktu. Jenis larutan yang dipakai pada penelitian ini adalah larutan asam sulfat ditambah variasi konsentrasi asam fosfat (10%, 30%, 40%, 70%, 100%). Agar diperoleh kondisi optimum untuk mendapatkan sifat-sifat lapisan yang diinginkan maka dilakukan variasi terhadap temperatur (10°C, 15°C, 20°C, 30°C) dan waktu (20-60 menit). Kondisi optimum yang diperoleh adalah sebagai berikut: konsentrasi asarn sulfat 60% + asam fosfat 40%, pH = 1, waktu 60 menit, temperatur 10°C, tegangan 20V dan rapat arus 7,4 A/dm2 dengan menghasilkan ketebalan lapisan optimum 43,8 µm dan kekerasan maksimum sebesar 154 VHN.

Atmospheric corrosion is the interaction between metal and the surrounding environment due to the humidity, oxygen and pollutant (chloride and sulphate particle) which is contains in the air. Marine is the most corrosive region due to the atmosphere contains chloride particle whose characteristic aggressive and accelerate corrosion rate. Anodizing is one of the most effective methods to prevent and control the corrosion rate. Anodizing is an electrolytic passivation process used to increase the thickness and density of the natural oxide layer on the surface of metal parts. Anodizing increases corrosion resistance and wear resistance. In this experiment used the sheet aluminum metal. The weather resistance of aluminum has linear relation to the thickness. In this investigation used some parameter processes like type of electrolyte, temperature, concentration and time variation. The medium which is used in this experiment is sulphate acid with added phosphate acid variation (0%, 10%, 40%, 70% and 100%). To achieve optimum condition the temperature (10°C, 15°C, 20°C, 30°C) and time variation (20-60 min) is carried out. The optimum condition of this experiment is the specimen which has hardness 154 HV and the thickness is 43,8 µm with electrolyte concentration sulphate acid 60%, phosphate acid 40%, temperature 10°C, time process 60 min, voltage 20 volt and current density 7,4 A/dm2."
Lengkap +
2007
T22896
UI - Tesis Membership  Universitas Indonesia Library
cover
Hutasoit, Martino R.
"Modifikasi permukaan aluminium secara elektrokimia merupakan suatu proses yang tengah berkembang pesat saat ini. Modifikasi permukaan secara elektrokimia pada awalnya lebih diarahkan pada peningkatan nilai ketahanan korosi, peningkatan kekerasan, dan juga peningkatan nilai estetika. Namun pada perkembangannya, salah satu proses elektrokimia, yaitu anodisasi, telah berkembang menjadi suatu proses modifikasi permukaan yang bertujuan untuk diaplikasikan pada teknologi berbasis nanoteknologi. Pemanfaatan lapisan oksida pada permukaan aluminium hasil proses anodisasi dilakukan dengan memanfaatkan pori (porous anodic alumina) yang terbentuk sebagai template pada pembuatan material yang berbasis pada nano teknologi seperti quantum-dot arrays, photonic crystals, magnetic memory arrays, nanowire dan berbagai alat mikroelektronik lainnya.
Penelitian ini bertujuan untuk mengetahui pengaruh perubahan konsentrasi larutan elektrolit terhadap ketebalan lapisan oksida yang terbentuk pada permukaan aluminium. Penelitian dilakukan dengan menggunakan sampel logam berupa aluminium foil (pure aluminium, 96.49%Al) dengan permukaan anodisasi sebesar 2X2 cm. Larutan elektrolit yang digunakan adalah asam oksalat dengan variasi konsentrasi 0.4 M, 0.5 M, 0.6 M. Tegangan pada proses adalah 32.5 Volt, temperatur dijaga pada rentang 4°C - 16°C, dan diaduk dengan menggunakan magnetic stirrer 500 rpm.
Hasil yang diperoleh melalui penelitian ini adalah bahwa tidak terjadi perubahan warna yang signifikan pada proses anodisasi dengan larutan asam oksalat. Nilai ketebalan lapisan oksida yang terbentuk akan semakin meningkat pada peningkatan konsentrasi asam oksalat. Nilai kekerasan pada sampel aluminium foil tidak dapat dilakukan dengan menggunakan metode microhardness tester.

Modification of aluminum surface with electrochemistry methods are developing rapidly nowadays. This surface modification were initially intended to increase the corrosion resistance, hardness, properties and improving the aesthetic appearance of aluminum. Recently, one of these electrochemistry methods, anodizing, were developed into one of the surface modification that can be applied in nanotechnology. Oxide layer which formed by anodizing process in the aluminum surface could be used as template for microelectronic nanotechnology material such as quantum-dot arrays, photonic crystals, magnetic memory arrays, nanowire because of it porous anodic alumina texture.
This research is conducted to found the effect of electrolyte concentration changes on thickness of oxide layer formed in aluminum surface. This research is carried out with aluminum foil sample (pure aluminum, 96.49% Al) with anodizing surface measured 2X2 cm. Electrolyte which used in this research is oxalic acid with concentration variation 0.4 M, 0.5 M, 0.6 M. This process using 32.5 Volt potential, temperature were kept in range of 4°C - 16°C, and the electrolyte were stirred electromagnetically at 500 rpm.
The result from this research shows that the colour of oxide layer by anodizing of aluminum in oxalic acid solution was transparent. By anodizing in oxalic acid, the thickness of formed oxide layer was dependent with the increase of concentration. Hardness testing on aluminum foil or oxide layer could?nt use to obtain hardness number in this research.
"
Lengkap +
Depok: Fakultas Teknik Universitas Indonesia, 2008
S41633
UI - Skripsi Open  Universitas Indonesia Library
cover
Panji Aji Wibowo
"Teknologi pengolahan bijih nikel kadar rendah dengan leaching mengunakan Asam Nitrat (HNO3) telah dikembangkan dan dipatenkan oleh suatu perusahaan riset Australia, Direct Nickel. Proses ini diklaim dapat mengolah semua range bijih nikel laterit dengan % ektraksi nikel dan kobalt mencapai > 90%. Salah satu keunggulan proses ini adalah reagen leaching dapat didaur ulang kembali dan menggunakan material SS 304 pada tangki reaktor. Namun proses ini tidak menghendaki adanya ion Cl- karena dikhawatirkan dapat merusak tangki reaktor. Umumnya Cl- ini dapat berasal dari air untuk proses atau dari bijih nikel itu sendiri.
Penelitian ini dilakukan untuk mengetahui perilaku korosi, terutama korosi sumuran dari material SS 304 dan SS 316 dalam campuran larutan HNO3 dan NaCl. Variasi campuran larutan HNO3 yang digunakan adalah 0.17 M, 0.52 M dan 1.73 M, yang menggambarkan kondisi free-acid di dalam reaktor Sedangkan variasi campuran larutan NaCl yang digunakan adalah 0.1 M dan 1 M. Pengujian yang dilakukan meliputi pengujian dengan metode polarisasi siklik dan electrochemical impedance spectroscopy (EIS).
Dari hasil pengujian polarisasi sikilik yang dilakukan, pitting corrosion terjadi pada sampel SS 304 dan SS 316 pada perendaman dalam campuran campuran larutan 1.73 M HNO3 dan 1 M NaCl dan pada sampel SS 304 dalam campuran campuran larutan 0.52 M HNO3 dan 1 M NaCl. Hal ini juga dikonfirmasi oleh hasil dari pengujian EIS. Pengamatan terhadap potensial korosi sumuran dari setiap tipe campuran HNO3 dan NaCl, secara umum SS 316 memberikani ketahanan terhadap korosi sumuran yang lebih baik dari SS 304, terutama akibat adanya unsur pemadu Mo. Pengujian pada komposisi lapisan oksida menunjukkan bahwa walaupun ditemukan adanya unsur Cl dalam lapisan tersebut, korosi sumuran cenderung tidak terjadi pada spesimen SS316.

Processing technology of low grade ores by Nitric Acid leaching has been developed and patented by an Australian research company, Direct Nickel. This process is claimed to be able to treat all the range of laterite ore with extraction of nickel and cobalt reach > 90%. One advantage of this process is the leaching reagent can be recycled back and use the 304 SS material in the reactor tank. The presence of Cl ions in the leaching process was avoided, because it feared could damage the reactor tank. The Cl- could comes form the water fro process or even the nickel ore.
This research was conducted to determine the corrosion behavior, particularly pitting corrosion of materials SS 304 and SS 316 in HNO3 and NaCl solution mixture . Variations HNO3 solution used was 0.17 M, 0.52 M and 1.73 M, which descriebd the variation of free-acid concentration in reactor. For NaCl solution using 0.1 M and 1 M concentration. The test was conducted with cyclic polarization method and electrochemical impedance spectroscopy (EIS).
From the results of cyclic polarization tests, pitting corrosion occurs on samples SS 304 and SS 316 after immersion in a mixed solution of 1.73 M HNO3 and 1 M NaCl, and the SS 304 samples in a mixed solution of 0.52 and 1 M HNO3 M NaCl. This is also confirmed by the EIS. By the observation of the pitting corrosion potential of each samples SS304 and SS316 immersed in each type of HNO3 anda NaCl solution mixture, generally SS316 provides good resistance to pitting corrosion rather than SS 304, mainly due to the presence of Mo as alloying element. Tests on the composition of the oxide layer indicates that although there is an element found in the layer Cl, pitting corrosion unlikely to have occurred on the specimen SS316."
Lengkap +
Depok: Fakultas Teknik Universitas Indonesia, 2014
T42971
UI - Tesis Membership  Universitas Indonesia Library
cover
Sipayung, Sandhy Putra Pangidoan
"Aluminium merupakan salah satu material logam yang banyak digunakan serta dikembangkan pada berbagai macam aplikasi. Untuk meningkatkan kualitas aluminium, baik sifat fisik maupun mekanisnya, dilakukan beberapa perlakuan terhadap aluminium tersebut. Salah satu proses yang dilakukan adalah dengan rekayasa permukaan melalui proses anodisasi. Dalam proses anodisasi, pada permukaan aluminium akan terbentuk lapisan aluminium oksida yang amat keras dan tahan terhadap korosi.
Saat ini pengembangan proses anodisasi dikembangkan dalam pengetahuan tentang nanoteknologi. Melalui proses anodisasi yang dilakukan diharapkan lapisan yang dihasilkan memiliki kebaikan sifat-sifat mekanis seperti ketebalan, kekerasan, dan karakteristik diameter pori yang sesuai agar nantinya dapat digunakan pada aplikasi nanoteknologi seperti pembuatan carbon nanotube, nanoporous membrane, ataupun quantum dots. Salah satu parameter yang terpenting dan menentukan karakteristik permukaan hasil anodisasi adalah konsentrasi dan jenis elektrolit yang digunakan.
Penelitian kemudian dilakukan untuk memahami pengaruh dari besarnya penambahan konsentrasi elektrolit terhadap karakteristik dari lapisan oksida yang dihasilkan pada permukaan aluminium foil. Pada penelitian ini digunakan elektrolit tetap asam oksalat 0,5 M, serta variabel bebas penambahan asam sulfat 0,12 M, 0,24 M, 0,36 M, dan 0,48 M.
Hasil penelitian kemudian menunjukkan bahwa lapisan oksida yang dihasilkan benar merupakan lapisan Al2O3 dan dengan meningkatnya konsentrasi asam sulfat lapisan oksida yang dihasilkan akan memiliki permukaan yang semakin pekat warna kelabu-nya serta meningkat ketebalannya, hingga mencapai ketebalan tertinggi sekitar 14,51 µm pada konsentrasi 0,36 M namun menurun hingga ketebalan 9,95 µm pada konsentrasi 0,48 M. Kekerasan lapisan yang dihasilkan tidak valid karena alat pengujian yang digunakan kurang mendukung untuk jenis sampel yang digunakan.

Aluminium is one of the most common metal that has been used and developed in wide application. To enhance the quality of aluminium (physical and mechanical properties), some process have been done to the aluminium itself. One of the process is by changing its surface properties with anodizing process. In anodizing process, the aluminium oxide layer would be formed on the surface, and it has great hardness and good corrosion resistance.
At the present, the anodizing process has been developed for the knowledge of nanotechnology. By anodizing, it is hoped that the layer produced would have good mechanical properties like thickness, hardness, and good pore diameter characteristic. Then, with it good properties, it can be used in nanotechnology application like in the manufacturing of carbon nanotube, nanoporous membrane, and quantum dots. One of the most important parameter to the characteristic of the anodizing surface layer is the use of electrolyte.
This experiment was conducted to study the effect of increasing electolyte concentration to the characteristic of the oxide layer that produced at the surface of aluminium foil. The experiment used 0,5 M oxalic acid mixed with 0,12 M, 0,24 M, 0,36 M, and 0,48 M sulfuric acid.
The results showed that the oxide layer was Al2O3 layer. With the increase of sulfuric acid concentration, the oxide layer would be darker in the colour of gray and has some increasing in thickness. The highest thickness was about 14,51 µm in the addition of 0,36 M electrolytic concentration, but it is decreased to the 9,95 µm thickness when the concentration increased up to 0,48 M. The hardness of the layer could not be tested. The hardness testing machine used was not supported the kind of sample that were tested.
"
Lengkap +
Depok: Fakultas Teknik Universitas Indonesia, 2008
S41736
UI - Skripsi Open  Universitas Indonesia Library