Hasil Pencarian  ::  Simpan CSV :: Kembali

Abstrak :
Aniline-4-sulfonate merupakan senyawa dengan gugus utama berupa cincin benzen, nitrogen dan sulfonat. Pada penelitian ini, senyawa aniline-4-sulfonate digunakan sebagai inhibitor untuk menekan laju korosi baja API 5L GRB N di dalam larutan asam sulfat 1 M. Potensiostat, alat uji kekerasan, alat uji kekasaran, mikroskop optik dan SEM digunakan untuk analisa jenis korosi, efisiensi inhibisi, mekanisme inhibisi, perubahan kekerasan dan kekasaran permukaan. Hasil pengujian menggunakan potensiostat memperlihatkan bahwa korosi yang terjadi pada baja API 5L GRB N adalah jenis korosi merata. Penggunaan inhibitor aniline-4-sulfonate dapat menekan laju korosi dengan efisiensi sebesar 60,29% pada konsentrasi 24,06 x 10-3M dan dapat mengurangi kerusakan terhadap kekerasan dan kekasaran melalui suatu mekanisme inhibisi mengikuti isoterm adsorpsi Langmuir dengan akurasi kelinieran (R2) mendekati 1 (satu). ......Aniline-4-sulfonate is compound with main groups are benzen ring, ammine, and sulfonate. On this research, aniline-4-sulfonate was used as corrosion inhibitor to reduced corrosion rate on API 5L GRB N steel in 1M sulphuric acid solution. Potensiostat, surface hardness tester, surface roughness terster, optical microscope, and SEM was used for corrosion type analysis, inhibition efficiency, inhibition mechanism, hardness and roughness damage. Examination using potensiostat showed that corrosion on API 5L GRB N steel was general corrosion type. Aplication aniline-4-sulfonate as inhibitor can pressed corrosion rate with efficiency 60,29 % at concentration 24,06 x 10 -3M, reduced hardness and roughness damage with adsorption mechanism followed Langmuir's adsorption isotherm with linearity accuration (R2) was 0,998.

Abstrak :
[ABSTRAK
Pipa jenis API 5L adalah yang sering dipakai untuk sistem transportasi tersebut. Dari berbagai peraturan yang terkini masih terdapat kegagalan pada sambungan pipa tersebut sehingga sering timbulnya terjadi kebakaran akibat tumpahnya minyak dari kegagalan sambungan las. Pada saat proses pengelasan yang berdasarkan peraturan atau rekomendasi seperti prosedur pengelasan (Welding Procedure Specification - WPS) sering kali tidak dapat diikuti secara benar sehingga akan mempengaruhi struktur mikro daerah terpapar panas lasan (Heat Affected Zone - HAZ). Pada penelitian ini akan diperbandingkan perbedaan Heat Input terhadapan ketangguhan dan kekuatan sambungan las. Kemudian dilakukan pengujian tidak merusak (Non Destructive Test-NDT) seperti Radiographic Test yang berguna untuk mengetahui cacat yang mungkin timbul dalam las-lasan. Kemudian pengujian merusak (Destructive Test-DT) seperti uji ketangguhan, uji keluluhan, uji impact, uji Crack Tip Open Displacement-CTOD untuk mengetahui kekuatan dan ketangguhan dari sambungan las. Dari hasil pengujian diatas Heat Input adalah unsur utama yang harus diperhatikan dalam proses pengelasan.

---

ABSTRACT
API 5L pipe is type of pipe very often used for the transportation system. From various current regulations there are still failures in the pipe joint, the frequent occurrence of a fire occurs due to the oil spill from the failure of the welded joint. During the welding process based on rules or recommendation such as welding procedures (Welding Procedure Specification - WPS) found cannot be followed correctly and will impact to the microstructure of the weld area exposed to heat (Heat Affected Zone - HAZ). This research will be compared to the difference Heat Input with toughness and strength of welded joints. Then Non-Destructive Test (NDT) as Radiographic Test useful to know the defects that may arise in the welding-weld. Then destructive testing (Destructive Test-DT) such as toughness test, impact test, test Crack Tip Open Displacement-CTOD to determine the strength and toughness of the welded joint. The result showed Heat Input is one of the elements that must be considered in the welding process.;API 5L pipe is type of pipe very often used for the transportation system. From various current regulations there are still failures in the pipe joint, the frequent occurrence of a fire occurs due to the oil spill from the failure of the welded joint. During the welding process based on rules or recommendation such as welding procedures (Welding Procedure Specification - WPS) found cannot be followed correctly and will impact to the microstructure of the weld area exposed to heat (Heat Affected Zone - HAZ) This research will be compared to the difference Heat Input with toughness and strength of welded joints. Then Non-Destructive Test (NDT) as Radiographic Test useful to know the defects that may arise in the welding-weld. Then destructive testing (Destructive Test-DT) such as toughness test, impact test, test Crack Tip Open Displacement-CTOD to determine the strength and toughness of the welded joint. The result showed Heat Input is one of the elements that must be considered in the welding process., API 5L pipe is type of pipe very often used for the transportation system. From various current regulations there are still failures in the pipe joint, the frequent occurrence of a fire occurs due to the oil spill from the failure of the welded joint. During the welding process based on rules or recommendation such as welding procedures (Welding Procedure Specification - WPS) found cannot be followed correctly and will impact to the microstructure of the weld area exposed to heat (Heat Affected Zone - HAZ) This research will be compared to the difference Heat Input with toughness and strength of welded joints. Then Non-Destructive Test (NDT) as Radiographic Test useful to know the defects that may arise in the welding-weld. Then destructive testing (Destructive Test-DT) such as toughness test, impact test, test Crack Tip Open Displacement-CTOD to determine the strength and toughness of the welded joint. The result showed Heat Input is one of the elements that must be considered in the welding process.]

Abstrak :
ABSTRAK
Penelitian ini difokuskan pada analisa korosi pipa trunk line yang menyebabkan pipa diganti dalam waktu 8 tahun dari 15 tahun rencana desain. Material baja API 5L Grade B dalam kondisi belum terpakai dan yang terkorosi dianalisis secara fisik dan mekanik menggunakan uji metalografi, uji tarik, uji komposisi kimia, Scanning electron microscopy-Energy Dispersive Spectroscopy (SEM-EDS), Difraksi Sinar-X (XRD), kemudian uji korosi dengan metode polarisasi. Pada sampel belum terpakai diperoleh nilai laju korosi 0,0531 mmpy dan sampel terkorosi diperoleh nilai 0,1377 mmpy. Juga terbentuk fasa Fe3O4 (magnetite), FeS (besi sulfida) dan SiO2 (silika). Hasil data di lapangan berupa kondisi sekitar jalur pipa trunk line dan laju korosi yang dihasilkan akibat penurunan ketebalan menghasilkan data sisa umur pakai aktual yang dibandingkan dengan sisa umur pakai sampel hasil pengujian.

---

ABSTRACT
This research focused on the trunk line corrosion analysis that has caused pipe replacement within 8 years instead of 15 years design lifetime. Samples of API 5L Grade B material were analyzed with physical and mechanical tests using metallographic, tensile testing, chemical composition test, scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), X-Ray difraction (XRD), then polarization corrosion test. On the new unused sample obtained corrosion Ade of 0.0531 mmpy and corroded sample obtained 0.1377 mmpy. Also formed phase Fe3O4 ( magnetite ) , FeS ( iron sulfide ) and SiO2 ( silica ). The results of field data in the form of conditions around the trunk line area and the pipeline corrosion rate generated due to decreased thickness obtained the actual remaining life data compared with the remaining lifetime of the sample test

Abstrak :
Kemampuan kombinasi ekstrak temulawak Curcuma Xanthorrhiza dan bawang Dayak Eleutherine Americana sebagai inhibitor ramah lingkungan untuk baja karbon API 5L X42 pada lingkungan HCl 1M diinvestigasi dengan pengujian tafel, weight loss, polarisasi, Electrochemical Impedance Spectroscopy EIS, dan Fourier Transform Infrared Spectroscopy FTIR. Senyawa flavonoid dan antioksidan yang berperan untuk menginhibisi korosi diinvestigasi melalui pengujian FTIR. Selain itu, lapisan yang terbentuk di permukaan logam juga dipelajari dengan menggunakan metode adsorpsi Langmuir isotherm. Campuran ekstrak temulawak dan bawang Dayak merupakan inhibitor jenis campuran, dan dominan pada katodik. Efisiensi inhibisi paling tinggi didapatkan dengan persentase 80 :20 yaitu 91,78. Campuran ekstrak temulawak dan bawang Dayak dapat digunakan sebagai alternatif inhibitor ramah lingkungan untuk baja karbon API 5L X42 pada lingkungan asam. ......This study aimed to investigate the ability of combination from Curcuma Xanthorrhiza and Eleutherine Americana extract as an environment friendly inhibitor for API 5L X42 steel in 1M HCl environment. Corrosion inhibition ability of this extract was tested using weight loss, tafel polarization, electrochemical impedance spectroscopy methods, and fourier transform infrared spectroscopy. FTIR test was used to investigate flavonoid and antioxidant compound that plays an important role to inhibit corrosion. In addition, formed layer on the metal surface was also studied using Langmuir isotherm adsorption methode. It can be concluded that combination from Curcuma Xanthorrhiza and Eleutherine Americana extract could be used as an alternative and environmental friendly inhibitor for API 5L X42 steel in acidid environment. Keywords API 5L X42 EIS FTIR green inhibitor polarization.

Abstrak :
Kemampuan kombinasi ekstrak temulawak Curcuma Xanthorrhiza dan bawang Dayak Eleutherine Americana sebagai inhibitor ramah lingkungan untuk baja karbon API 5L X42 pada lingkungan HCl 1M diinvestigasi dengan pengujian tafel, weight loss, polarisasi, Electrochemical Impedance Spectroscopy EIS , dan Fourier Transform Infrared Spectroscopy FTIR . Senyawa flavonoid dan antioksidan yang berperan untuk menginhibisi korosi diinvestigasi melalui pengujian FTIR. Selain itu, lapisan yang terbentuk di permukaan logam juga dipelajari dengan menggunakan metode adsorpsi Langmuir isotherm. Campuran ekstrak temulawak dan bawang Dayak merupakan inhibitor jenis campuran, dan dominan pada katodik. Efisiensi inhibisi paling tinggi didapatkan dengan persentase 80 :20 yaitu 91,78 . Campuran ekstrak temulawak dan bawang Dayak dapat digunakan sebagai alternatif inhibitor ramah lingkungan untuk baja karbon API 5L X42 pada lingkungan asam. ......This study aimed to investigate the ability of combination from Curcuma Xanthorrhiza and Eleutherine Americana extract as an environment friendly inhibitor for API 5L X42 steel in 1M HCl environment. Corrosion inhibition ability of this extract was tested using weight loss, tafel polarization, electrochemical impedance spectroscopy methods, and fourier transform infrared spectroscopy. FTIR test was used to investigate flavonoid and antioxidant compound that plays an important role to inhibit corrosion. In addition, formed layer on the metal surface was also studied using Langmuir isotherm adsorption methode. It can be concluded that combination from Curcuma Xanthorrhiza and Eleutherine Americana extract could be used as an alternative and environmental friendly inhibitor for API 5L X42 steel in acidid environment.

Abstrak :
Pengaruh kombinasi ekstrak daun Physalis angulata daun ciplukan dan daun Cassia angustifolia daun jati cina sebagai inhibitor ramah lingkungan dengan perbandingan 50:50 pada baja karbon API 5L diinvestigasi. Pengujian dilakukan dalam lingkungan HCl 1M. Pengujian yang dilakukan meliputi polarisasi potensiodinamik, kehilangan berat, dan EIS. Senyawa antioksidan diinvestigasi melalui pengujian FTIR. Sesuai dengan pengujian FTIR, senyawa antioksidan yang terkandung pada kombinasi ekstrak ini adalah flavonoid. Variabel yang digunakan adalah konsentrasi inhibitor, yaitu 10 ml, 30 ml, dan 50 ml. Diketahui bahwa semakin tinggi konsentrasi yang diberikan, maka semakin tinggi kemampuan inhibitor dalam menginhibisi permukaan baja dimana efisiensi inhibitor paling tinggi didapatkan dengan konsentrasi 50 ml. Kombinasi ekstrak daun ciplukan dan daun jati merupakan inhibitor jenis campuran yang lebih dominan ke katodik. Metode adsorpsi inhibitor ini mengikuti adsorpsi isotherm Langmuir dengan tipe adsorpsi fisika atau physisorption. ......The effect of combination of Physalis angulata leaf and Cassia angustifolia leaf extract as green inhibitor with a 50:50 ratio for API 5L steel was investigated. This experiment was carried in 1M HCl solution by using different concentrations as variables which is 10 ml, 30 ml, and 50 ml inhibitor extracts. This experiment was evaluated using potentiodynamic polarization, EIS, and weight loss. The antioxidant compound was investigated using FTIR and was found to be flavonoid. It was found that the capability of the inhibitor to inhibit the steel surface from the environment increases with increasing concentration, which 50 ml concentration is found to have the best efficiency of all concentrations. Combination of physalis angulata leaf and cassia angustifolia leaf extract is found to be a mixed type inhibitor with predominant cathodic effectiveness. The adsorption of this inhibitor on the steel surface was predominantly through physisorption and obeyed Langmuir adsorption isotherm.

Abstrak :
Telah dilakukan penelitian untuk mengetahui pengaruh air formasi berinhibitor terhadap perilaku korosi dan laju korosi baja API 5L Grade B. Metode yang digunakan yaitu Weight loss dan Polarisasi Potensiodinamik. Uji celup dilakukan dengan variasi waktu 8, 11, dan 14 hari. Hasil penelitian menunjukkan bahwa kondisi baja API 5L dalam larutan air formasi berinhibitor mengalami pemasifan dan laju korosi semakin menurun seiring pertambahan waktu. Hasil pengujian XRD menunjukkan bahwa produk korosi yang dihasilkan adalah Fe3O4. ......A research has been conducted to know the influences formation water with presence of inhibitor to the corrosion behaviour and corrosion rate API 5L Grade B steel. Weight loss and Potentiodynamic Polarization methodology has been carried out. An immersion test with various time 8,11, and 14 days has been done. This research has show that passivity happened and the corrosion rate has decreased as the increased of time. The corrosion product of Fe3O4 has been known as the result of XRD test.

Abstrak :
Pipa penyalur minyak umumnya menggunakan material baja karbon. Salah satu masalah besar dalam penggunaan material tersebut yang berkaitan dengan korosi dan biasanya terjadi kebocoran adalah akibat adanya pengaruh konsentrasi ion klorida yang terlarut dalam media air sehingga lingkungan bersifat korosif (asam). Oleh karena itu sebagai upaya untuk mengatasi masalah tersebut perlu diketahui besaran laju korosi material baja karbon tersebut. Dalam penelitian ini dilakukan perbandingan antara laju korosi yang diperoleh dari metode pengujian linear polarisasi resistance dan pengukuran metal loss dengan peralatan ultrasonic thickness meter. Output dari kedua metode tersebut selanjutnya diperoleh hubungan laju korosi melalui analysis of variance dengan menggunakan software. Studi pengaruh kadar klorida dilakukan untuk mengetahui korosi internal pipa baja karbon API 5L Grade B yang digunakan sebagai pipa penyalur minyak di lapangan. Metode pengujian polarisasi resistance dilakukan dalam media larutan air formasi NaCl 1%, 2% dan 3.5%. Laju korosi internal pipa baja karbon API 5L Grade B cenderung meningkat seiring dengan meningkatnya konsentrasi klorida dalam media larutan. Penelitian ini juga menunjukkan bahwa pipa baja karbon API 5L Grade B memiliki ketahanan korosi yang cukup pada fluida dengan konsentrasi klorida 1%, 2% dan 3.5%. ......Oil pipeline is commonly used carbon steel. One of the big caused on using that material which related to corrosion problem and usually there is such as leakage due to effect of ion chloride concentration in water that causes corrosive environment (acid). In order to overcome this problem is necessarily to know corrosion rate of this steel. In this study, output comparison of corrosion rate measurement methods are resistance polarization and metal loss measurement with ultrasonic. Correlation factor between both methods of corrosion rate measurement will achieved by analysis of variance from software. The aim of this research is to study effect chloride level to internal corrosion carbon steel API 5L Grade B and carbon steel that used as oil pipeline in the field. A method used for corrosion testing is resistance polarization which was used formation water solution with NaCl 1%, 2% and 3.5%. The corrosion rate for carbon steel API 5L Grade B tend to increase accompanied with more chloride content in the medium, respectively. This research also explain that carbon steel API 5L Grade B have corrosion resistance fairly to fluid with chloride content 1%, 2% and 3.5%.