Hasil Pencarian  ::  Simpan CSV :: Kembali

Abstrak :
Graft copolymerization of an acrylonitrile monomer onto Deproteinized Natural Rubber (DPNR) is an important process in the modification of Natural Rubber (NR) to increase its oil resistance. However, coagulation at the beginning of the process was a problem causing a copolymerization foil to occur. The presence of a styrene monomer is therefore expected to improve the emulsion condition so that coagulation can be prevented in the early reaction step. For comparison purposes, the processes with and without styrene were investigated. The influence of the concentration of styrene as well as the ratio of the DPNR:monomer on the stabilization process were also observed. The results showed that the addition of styrene could improve the stabilization process as proven by Fourier Transform Infrared Spectroscopy (FTIR). The presence of the functional group of CºN at FTIR proved the production of the polyacrylonitrile in the mixture. The investigation showed that the concentration of styrene monomer, which led to the emulsion stability, is up to 1.5 wt% concentration of styrene at the ratio of DPNR:monomer (M) of 70:30 wt%.

Abstrak :
In order to find an alternative method for the physical properties improvement of rayon sheet, a chemically graft copolymerization of acrylamide to rayon sheet by using cerric ammonium nitrate as an initiator under nitrogen atmosphere had been, successfully, carried out. Several circumstances that influence the degree of grafting and physical properties of rayon sheet were studied at various concentration of initiator, concentration of monomer (acrylamide), period of pre-initiation time, temperature and time of grafting process. The occurrence of acrylamide grafted to rayon sheet was evaluated by measuring the increase in weight of the treated rayon sheet and by the appearance of specific IR spectrum. Moreover, mechanical and physical property e.g. tensile strength unit, rigidity unit, and color absorption of the original rayon and grafted rayon were also evaluated. The results from the mentioned study, briefly, can be reported as follow. In general, the degree of grafting (%grafting) increases with the increasing or initiator concentration, monomer concentration, temperature and time period of grafting process. Coincidentally, in all cases the value of rigidity unit and the ability to absorb particular dyes increase in line with the increasing in the degree of grafting. The tensile strength unit of the grafted rayon, however, does not show the similar trend. It was observed that the tensile strength unit showed an improvement only up to certain value of the degree of grafting, then become worst on farther increasing in the degree of grafting. The degree of grafting that result the best tensile strength unit (optimum) was found to be in the values in of 11 to 12 % . The experimental condition that results the mentioned degree of grafting can be achieved by combination of initiator concentration, acrylamide concentration, pre-initiation time, grafting process time, and grafting temperature at 0.5 %; 4%; 5minutes; 35 minutes; and 60° C, respectively. The occurrence of grafted acrylamide to rayon sheet was also evidenced by appearing IR signal at 1684 cm 1 (for the indication of the introduction of carbonyl group). Although not very clear, due to absorption band overlapping from hydroxyl group, the IR signal at 3362 cm-1 and 3373 cm " (for the indication of amide group introduction) provide another evidence for the successful of grafting process.

---

Pencangkokan akrilamida pada kain rayon secara kimiawi dengan menggunakan inisiator ceric ammonium nitrat didalam atmosfir nitrogen, sebagai upaya alternalif untuk memperbaiki sifat-sifat fisik rayon, telah berhasil dilakukan. Pengaruh beberapa faktor terhadap-besarnya kadar pencangkokan dan sifat-sifat fisik rayon dipelajari dengan memvariasikan, antara lain, konsentrasi inisiator, konsentrasi monomer, waktu pra inisiasi, temperatur dan waktu pencangkokan. Keberhasilan terjadinya pencangkokan akrilamida pada kain rayon ditandai atau diarnati dengan kenaikan berat rayon (persen pencangkokan) dan perubahan spesifik spektrum infra merahnya. Terhadap rayon asli dan rayon tercangkok dilakukan beberapa evaluasi sifat fisik yang meliputi uji kekuatan tarik, uji kekakuan, dan daya scrap terhadap zat warna. Dari penelitian yang lelah dilakukan dapat dilaporkan bahwa harga persen pencangkokan semakin besar dengan semakin tingginya konsentrasi inisiator, konsentrasi monomer, temperatur dan waktu pencangkokan. Sementara itu dari uji sifat fisik ditemukan bahwa dengan semakin besarnya harga persen pencangkokan maka daya serap terhadap zat warna dan kekakuannya semakin besar. Namun tidak demikian dengan kekuatan dari kain rayon yang tercangkok. Ditemukan bahwa kekuatan tarik kain rayon naik sejalan dengan besarnya persen pencangkokan hanya sampai pada harga persen pencangkokan tertentu, kemudian turun lagi meskipun harga persen pencangkokannya bertambah hesar. Besarnya persen pencangkokan tertentu tersebut, yang memberikan kekuatan tarik paling besar (optimum), dicapai pada persen pencangkokan sebesar 11 sampai dengan 12 %. Sedangkan kondisi-kondisi untuk memperoleh persen pencangkokan tersebut dapat dicapai dengan konsentrasi irisiator, konsentrasi monomer , waktu pra inisiasi, waktu pencangkokan, dan suhu pencangkokan masing masing sebesar 0,5 %, 4 %, 5 rnenit, 35 menit dan 60° C. Disamping itu dapat dilaporkan bahv,ra keberhasilan pencangkokan akrilamida pads kain rayon ditandai dengan munculnya puncak serapan 1R pada bilangan gelombang 1684 cm-' sebagai indikasi terintroduksikannya gugus karbonit [C=D] dan, meskipun tidak terlalu nyata karena adanya tumpang suh dengan pity serapan gugus hidroksi, kecenderungan adanya puncak serapan pada bilangan geloinbang 3362 cm"' dan 3373 cm-' sebagai indikasi terintroduksinya gugus amida pada kain rayon.

Abstrak :
Pencangkokan 4-vinilpiridin pada serat polipropilen dengan teknik radiasi, sebagai alternatif untuk membuat serat penukar ion telah dilakukan, Pengaruh kondisi radiasi, metoda pencangkokan, dosis, laju dosis, jenis pelarut, komposisi pelarut , dan konsentrasi monomer terhadap kadar pencangkokan dipelajari. Analisis dan karakterisasi serat polipropilen sebelum dan sesudah pencangkokan dilakukan dengan, ESR, FT-IR, DTAITGA, XRD, dan SEM-EDAX . Kapasitas penukaran serat PP-g-4VP terhadap ion Cue` dalam larutan analisis dengan ICP-MS. Hasil yang diperoleh dari ESR menunjukkan bahwa kondisi radiasi yang terbaik adalah oakum. Metoda yang memberikan kadar pencangkokan tertinggi adalah metoda simultan. Semakin tinggi dosis, laju dosis dan konsentrasi monomer, maka makin tinggi kadar pencangkokan. Makin menurun polaritas pelarut dalam pelarut homolog alkohol maka makin tinggi kadar pencangkokan, akan tetapi semakin tinggi kadar air didalam pelarut alkohol semakin tinggi kadar pencangkokan. Pelarut n-butanol menunjukkan kinetika pencangkokan lebih baik, dengan laju pencangkokan awal lebih tinggi di banding pelarut campuran metanol-air , Hubungan antara laju pencangkokan awal terhadap laju dosis dalam pelarut n-butanol adalah Rp = C I 0.35 ; sedangkan dalam pelarut metanol- air Rp = C I "7. Spektrum serapan FT-IR menunjukkan munculnya pita serapan vibrasi ulur u (C=C) dan u(C-H) aromatik pada bilangan gelombang 1625 dan 3020 cm-', dan pita serapan vibrasi ulur u (C-N) pada bilangan gelombang 1177 dan 1388 cm 1, yang berarti 4-vinilpiridin berhasil dicangkokan pada serat polipropilen. Pengamatan dengan SEM memperlihatkan perbedaan diameter dan permukaan serat polip ropilen sebelum dan sesudah dicangkok, sedangkan dari EDAX menunjukkan ion Cue+ telah diadsorpsi oleh serat PP-g-4VP dan terdistribusi secara merata, dengan kapasitas penukaran 3,4 mek/gram serat. Termogram DTAITGA menunjukkan pencangkokan 4-vinilpiridin pada serat polipropilen menunukkan kesetabilan termalnya, dan dari diffraktogram XRD menunjukkan terjadi perubahan fasa kristalin serat polipropilen setelah dicangkok.

---

Influence of Solvents on Graft Copolymerization Kinetics of 4-vinilpiridin onto Polypropylene Fibers by Simultaneous Methods in Vacuum Atmosphere Radiation graft copolymerization of 4-vinilipiridin onto polypropylene fibers, for synthesis of ion exchange fibers has been done. The effect of radiation condition, graft methods, dose, dose rate, solvents and monomer concentrations on the grafting yields was also studied. Analysis and characterization of polypropylene fibers before and after grafting was done by ESR, FT-IR, DTAITGA, XRD and SEM-EDAX. The ion exchange capacity of PP-g-4VP fibers on Cue+ ion was determined by ICP-MS. The ESR spectra showed that vacuum atmosphere was the best irradiation condition. The higher grafting yields were obtained by simultaneous method. The grafting yields increased with increasing dose, dose rate, monomer concentration and H2O content within alcohol-water solvents system. The grafting yields also increased if polarity of alcohol decreased in using homologue alcohol solvent system. The initial copolymerization rate in n-butanol solvents was higher than methanol-water solvents, with Rp = C 10.35 in n-butanol and, Rp = C I 0.57 in methanol-water solvents, Infra red spectra showed characteristic band sorption on wave length 1625 and 3020 cm 'I for C-H and C=C aromatic stretching, and 1177 and 1388 cm-' for C-N stretching. Observation by using SEM-EDAX showed the difference between polypropylene before and after grafted by 4-vinilpiridin, and Cue+ ion was homogeneously adsorbed by PP-g-4VP fibers, with adsorbed capacity 3.4 meg/gr. DTAITGA thermogram showed, that grafted 4-vinilpiridin onto polypropylene fibers was decreased its thermal stability, and X-ray diffractogram showed that crystalinity of polypropylene was changed after grafted by 4-vinilpiridin.

Abstrak :
Telah dilakukan modifikasi serat polipropilen dengan asam akrilat supaya dapat dipergunakan untuk penukar kation. Penelitian ini bertujuan untuk mendapatkan serat yang dapat menukar ion logam dalam larutan ;dengan kapasitas tinggi. Kopolimerisasi cangkok asam akrilat pada serat polipropilen dilakukan dengan metode peroksidasi menggunakan sinar dari sumber Co-60. Pengaruh beberapa faktor terhadap kadar pencangkokan dipelajari dengan memvariasikan dosis total iradiasil, temperatur dan waktu pencangkokan serta konsentrasi monomer. Variasi laju dosis dilakukan untuk mengetahui kecepatan pencangkokan. Terjadinya pencangkokan asam akrilat pada serat polipropilen diamati pada spektrum infra merah, dan kestabilan termal serat polipropilen sebelum dan sesudah pencangkokan (PP-g-AAc) diamati dengan Thermogravimetric Analysis (TGA). Rapasitas penukaran serat PP-g-AAc terhadap ion logam dalam larutan diperiksa dengan Atomic Absorption Spectrofotometer (AAS). Hasil yang diperoleh menunjukkan bahwa makin tinggi dosis total dan konsentrasi monomer makin tinggi kadar pencangkokan. Dari variasi temperatur dan waktu pencangkokan diperoleh energi pengaktivan pencangkokan asam akrilat pada serat polipropilen sebesar 5,031 kcal/mol. Pengamatan terhadap hubungan laju dosis dengan kecepatan pencangkokan diperoleh persamaan RP = C I0,8 yang berarti pada reaksi pencangkokan di samping terjadi kopolimer cangkok terjadi pula homopolimer asampoll akrilat. Pengamatan pada spektra infra merah membuktikan terjadinya pencangkokan pada bagian amorf serat. Serat PP-g-AAc yang dihasilkan mempunyai kapasitas penukaran untuk ion Cu2+ adalah sebesar 3,14 mek/g.

---

Graft copolymerization of acrylic acid onto polypropylene fiber (PP) has been studied by preirradiation technique using co" gamma rays source. The preirradiated PP was treated with acrylic acid solution and heated at various temperature and period under nitrogen atmosphere. The percentage of grafting was determined and evaluated as function of total dose, reaction time, temperature and monomer concentration. The rate of grafting was studied as the function of dose rate. The grafted PP was characterized by IR spectroscopy TGA (Thermogravimetry Analysis) and the exchange capacity towards Cu(II). From the results the activation energy calculated is 5,031 kcal/mol. The rate of grafting follow the equation of Rp = CI0'8 which is indicate that the grafting mechanism should through bimolecular mechanism. IR spectra shows that the monomer grafted on the amorf part of PP. The exchange capacity of PP-g-AAc prepared for Cu(II) is 3,14 meq/g.;Graft copolymerization of acrylic acid onto polypropylene fiber (PP) has been studied by preirradiation technique using co" gamma rays source. The preirradiated PP was treated with acrylic acid solution and heated at various temperature and period under nitrogen atmosphere. The percentage of grafting was determined and evaluated as function of total dose, reaction time, temperature and monomer concentration. The rate of grafting was studied as the function of dose rate. The grafted PP was characterized by IR spectroscopy TGA (Thermogravimetry Analysis) and the exchange capacity towards Cu(II). From the results the activation energy calculated is 5,031 kcal/mol. The rate of grafting follow the equation of Rp = CI0'8 which is indicate that the grafting mechanism should through bimolecular mechanism. IR spectra shows that the monomer grafted on the amorf part of PP. The exchange capacity of PP-g-AAc prepared for Cu(II) is 3,14 meq/g.

Abstrak :
Film selulosa bakteri telah berhasil dibuat dari air kelapa sebagai sumber mikronutrien menggunakan biakan Acetobacter xylinum. Film selulosa bakteri selanjutnya diiradiasi dengan mesin berkas elektron pada rentang dosis 15-120 kGy, laju dosis 15 kGy/ pass dan temperatur ruang. Setelah diiradiasi, selulosa bakteri tersebut dikopolimerisasi cangkok dengan monomer akrilonitril. Kondisi optimum untuk kopolimerisasi cangkok akrilonitril pada selulosa bakteri adalah pada dosis 75 kGy, temperatur 600C, waktu 3 jam, dan konsentrasi akrilonitril 30% b/b. Derajat pencangkokan tertinggi yang diperoleh adalah sebesar 56,03 %. Selulosa bakteri tercangkok akrilonitril (SB tercangkok PAN) selanjutnya diamidoksimasi. Amidoksimasi dilakukan dengan penambahan hidroksilamin hidroklorida 6 % b/v dalam pelarut metanol : air = 50 : 50 v/v pada pH 7, dan diperoleh waktu optimum selama 2 jam dengan densitas gugus amidoksim yang diperoleh sebesar 5,425 mmol/ gram. Karakterisasi gugus fungsi film selulosa bakteri sebelum dan sesudah kopolimerisasi cangkok dengan akrilonitril, serta setelah diamidoksimasi dilakukan dengan menggunakan Fourier Transform Infra Red (FTIR), analisis mikrostruktur dengan Scanning Electron Microscopy (SEM), analisa derajat kristalinitas menggunakan X-ray diffraction (XRD), serta uji ketahanan terhadap panas diukur dengan Thermal Gravimetry Analysis (TGA) dan Differential Scanning Calorimetry (DSC). Hasil karakterisasinya mengindikasikan bahwa SB tercangkok PAN dan selulosa bakteri teramidoksimasi (SB-Am) telah berhasil disintesis pada penelitian ini. Film tersebut selanjutnya diuji kemampuan adsorpsinya terhadap ion logam Cu2+ dan Pb2+. Nilai koefisien distribusi selulosa bakteri, SB tercangkok PAN, dan SB-Am pada pH 6 terhadap ion logam Cu2+ masing-masing sebesar 0,26, 0,23, dan 0,37 L/gram adsorben, sedangkan terhadap ion logam Pb2+ masing-masing sebesar 0,41, 0,405, dan 0,52 L/gram adsorben.

---

Bacterial cellulose films have been successfully synthesized from coconut water as a source of micronutrients using Acetobacter xylinum. Bacterial cellulose film irradiated using electron beam machine at a dose range of 15-120 kGy and dose rate 15 kGy/ pass in room temperature. After irradiated, the bacterial cellulose grafted with acrylonitrile monomer. The optimum conditions for graft copolymerization condition were at the dose of 75 kGy, temperature 600C ,3 hours time of reaction, and the concentration of acrylonitrile was 30 % w/w. The highest degree of grafting obtained was 56,03 % . Amidoximation then performed by the addition of hydroxylamine 6 % w/v in methanol : water = 50 : 50 v/v solvent under pH 7 and obtained the optimum time for amidoximation reaction was 2 hours. Amidoxime density obtained was 5.425 mmol/ gram. Characterization of functional groups in bacterial cellulose films before and after graft copolymerization with acrylonitrile, as well after amidoximation performed by Fourier Transform Infrared (FTIR), microstructure was analyzed by Scanning Electron Microscopy (SEM), analysis of the degree of crystallinity using X-ray diffraction (XRD), thermal resistance properties was measured by Thermal Gravimetry Analysis (TGA) and Differential Scanning Calorimetry (DSC) .The results show that bacterial cellulose-g-polyacrylonitrile (BC-g-PAN) and amidoximated bacterial cellulose films (Am-BC) have been synthesized successfully. Subsequently, Cu2+ and Pb2+ metal ion adsorption studies were conducted using those films. Coeficient distribution of bacterial cellulose, BC-g-PAN, and Am-BC under pH 6 toward Cu2+ions respectively were 0,26, 0,23, dan 0,37 L/gram of adsorbent, while toward Pb2+ions, respectively were 0,41, 0,405, and 0,52 L/gram of adsorben.

Abstrak :
Telah disintesis serat rayon terikat silang N,N?-Metilendiakrilamida (NBA) sebagai matriks pencangkokkan asam akrilat (AA) yang memiliki derajat pengembangan dalam air berkisar antara 300-400% serta tahan terhadap kondisi asam dan basa. Inisiasi ikat silang dan pencangkokkan monomer dilakukan dengan metode ozonasi dalam udara. Metode ini dapat digunakan untuk memisahkan, mengontrol dan mengoptimasi pembentukan ikat silang dan pencangkokkan monomer AA dalam media N2. Gugus peroksida dan hidroperoksida yang terbentuk pada serat rayon pada berbagai variasi laju alir, waktu ozonasi, berat dan kerapatan serat ditentukan dengan metode iodometri dalam fasa organik. Pembentukan ikat silang dilakukan pada berbagai konsentrasi monomer dan suhu reaksi. Pencangkokkan AA pada serat yang telah terikat silang dilakukan melalui variasi waktu ozonasi kembali dan konsentrasi monomer. Serat rayon-co-NBA-g-Poliakrilat yang dihasilkan dikarakterisasi menggunakan FTIR. Kadar peroksida pada serat semakin tinggi dengan meningkatnya laju alir dan waktu ozonasi. Hasil yang diperoleh menunjukkan makin tinggi derajat ikat silang, makin sedikit AA yang dapat tercangkok. Derajat pengembangan dan ketahanan serat terhadap kondisi asam dan basa dipengaruhi oleh banyaknya ikat silang dan kadar AA tercangkok. Semakin banyak jumlah ikat silang pada serat, derajat pengembangan akan menurun dan ketahanan terhadap kondisi asam dan basa meningkat. ......Cross-linked rayon fiber with N,N'-Methylenediacrylamide (NBA) as graft copolymerization matrix of acrylic acid (AA) has been synthesized. The grafted fibers which is resistant to acidic and alkaline conditions shown degree of swelling between 300-400%. The initiation of the cross-link formation and graft copolymerization of monomer were carried out by ozonation method in the air. This method can be used to separate, to control and to optimize the cross-link process and graft copolymerization of AA in the media of N2. Peroxide and hydroperoxide groups formed on the rayon fibers at various flow rate, ozonation time, weight and density were determined by iodometric method in the organic phase. Cross-linked rayon fibers was prepared at various monomer concentrations and reaction temperature. The graft copolymerization of acrylic acid on the crosslinked fiber is conducted at various ozonation time and AA concentration. Rayon fiber-co-NBA-graft-Polyacrylic were characterized using FTIR. Peroxide concentration on the rayon fibers increases with flow rate and ozonation time. The result showed the increases in degree of cross-linking will decreases the amount of AA grafted. It was observed that the fiber swelling and resistant to acidic and alkaline conditions were depend on degree of crosslinking and the total of carboxylic group grafted onto rayon fiber. The higher concentration of crosslinking agent, the degree of swelling will be lower and stability in acidic and alkaline condition will be increases.

Abstrak :
Diversifikasi barang jadi karet alam sangat diperlukan untuk mendukung peningkatan konsumsi domestik produksi karet alam nasional. Salah satu upaya yang dapat dilakukan adalah dengan memanfaatkan karet alam termoplastik hasil kopolimerisasi cangkok emulsi lateks karet alam dengan monomer termoplastik sebagai bahan aditif jenis peningkat indeks viskositas minyak pelumas. Penelitian ini dimaksudkan untuk mempelajari pengaruh penambahan berbagai dosis karet alam termoplastik (kopolimer dari karet alam - stirena) ke dalam minyak lumas dasar golongan parafinik HVI 60 dan HVI 650 terhadap nilai indeks viskositas minyak pelumas baru. Hasil penelitian menunjukkan bahwa reaksi kopolimerisasi cangkok emulsi yang dijalankan pada rasio karet alam terhadap monomer stirena sebesar 85:15, pada suhu 65oC selama 7 jam, dengan penambahan 1% insiator amonium peroksidisulfat dan 2% surfaktan sodium dodesil sulfat mampu menghasilkan karet alam termoplastik (TPNR, kopoli NR-ST) dengan efisiensi cangkok 56,48%. Pada dosis 5% TPNR terhadap minyak lumas dasar berfungsi dengan baik sebagai peningkat indeks viskositas karena memenuhi persyaratan indeks viskositas standar sesuai Surat Keputusan Ditjen Migas Nomor 85K/34/DDJM/1998, dan dapat bersaing dengan minyak pelumas komersial tipe 20W-50, 10W-40 dan 15W-40. ......Diversification of rubber goods are highly needed to enhance natural rubber domestic consumption. One of the efforts is by using thermoplastic natural rubber that is synthesized from emulsion graft copolymerization of natural rubber latex with thermoplastic monomer as index viscosity improver of lubricating oil. The research aimed to study the effect of thermoplastic natural rubber (natural rubber?styrene copolymer) addition, at various concentration, into base paraffinic lube oil (HVI 60 and HVI 650) on index viscosity value of lubricating oil. The result showed that emulsion graft copolymerization at composition ratio of natural rubber to styrene monomer 85:15, at 65oC for 7 hours, with addition of 1% ammonium peroxidisulfate as initiator and 2% sodium dodecyl sulfate as surfactant produced thermoplastic natural rubber (TPNR, copoly NR-ST) with grafting efficiency of 56,48%. The TPNR can be functioned properly as index viscosity improver at 5% concentration to base paraffinic lube oil either HVI 60 or HVI 650. The obtaining new lubricating oils could fulfill the index viscosity standard requirement refered to Decree of Directorat General of Oil and Gas No 85K/34/DDJM/1998, and could compete with the commercial lubricating oil type 20W-50, 10W-40, and 15W-40.