Hasil Pencarian  ::  Simpan CSV :: Kembali

Abstrak :
Surface Mechanical Attritition Treatment adalah salah satu proses fabrikasi nano material dengan cara memberikan deformasi mekanis strain-induced pada permukaan material. Penelitian ini memberi perlakuan SMAT pada stainless steel AISI 304 yang merupakan austenitic stainless steel. Deformasi yang diperlakukan pada permukaan material akan menghasilkan gradien regangan di seluruh bagian material. Perbedaan regangan dan strain rate mempengaruhi struktur yang terjadi. Semakin tinggi regangan yang diberikan (semakin dekat dengan permukaan) menghasilkan butir yang lebih halus hingga skala nanometer. Dan sebaliknya, semakin rendah regangan yang dialami maka akan dihasilkan butir yang kasar.. Proses SMAT pada baja juga dapat menghasilkan transformasi fasa dari austenit ke martensit. Analisis XRD menunjukkan peningkatan kandungan martensit pada lapisan yang terkena regangan tinggi. Pengamatan TEM menunjukkan transformasi martensit terjadi dengan dua mekanisme yaitu dari austenit yang berstruktur kristal FCC () menjadi martensit yang berstruktur kristal HCP (ε) dan dari austenit yang berstruktur kristal FCC () menjadi martensit yang berstruktur kristal BCC (α’). Transformasi ini mengikuti arah dan hubungan kristalografi Kurdjumov-Sachs (K-S) orientation yaitu 〈1-10〉γ//〈112-0〉ε//〈11-1〉α. Sementara pada bagian yang terkena regangan lebih rendah tetap mengandung fasa austenit. Kombinasi dari butir halus dan kasar serta austenit dan martensit pada material yang sama memungkinkan untuk mendapatkan material yang kuat sekaligus tangguh. Butir halus dan fasa martensit pada permukaan akan meningkatkan kekerasan material, sementara butir kasar dan fasa austenit pada bagian lebih dalam akan mempertahankan keuletan material. ......Surface Mechanical Attritition Treatment is one of nano material fabrication method which done by applying strain-induced mechanical deformation on the surface. This research treated stainless steel AISI 304 which is austenitic stainless steel type, with SMAT. The deformation cause strain gradient through out the sample. Strain level differences give effect to material structure. Higher strain which happen closely to the surface region, result in finer grain up to nano scale, while lower strain cause more coarse grain. SMAT on stainless steel also could cause phase transformation from austenite to martensite. XRD analysis showed increase of martensite content on higher strain-affected layer. TEM observations showed martensite transformation by two mechanism, austenite with FCC crystal structure () to martensite with HCP crystal structure (ε) and austenite with FCC crystal structure () to martensite with BCC crystal structure (α’). This transformation are following crystalographic orientation relationship of Kurdjumov-Sachs (K-S), 〈1-10〉γ//〈112- 0〉ε//〈11-1〉α. While on the other region that less-affected by strain still contain austenite phase. Combination of fine grain-coarse grain and austenite-martensite phase on the same material could result in higher properties material since it could has high strenght and high toughness. Fine grain and martensite phase on the surface will increase the hardness of material, while coarse grain and austenite phase on deeper layer will increase the ductility of material.

Abstrak :
Nanofluida adalah jenis fluida yang sedang dikembangkan yang memiliki sifat konduktivitas yang lebih tinggi dibandingkan dengan air. Penelitian lebih lanjut diperlukan agar fluida baru ini dapat diaplikasikan secara efektif dan efisien. Tujuan dilakukannya pcnelilian ini adalah mempelajari pengamh penambahan partikel nano pada air terhadap nilai koefisien gesek jika Huida ini dialirkan pada pipa lurus. Penelitian dilakukan dengan cara mengalirkan fluida air dan nanofluida A1103 dcngan menvariasikan kecepatan aliran pada pipa lums berukuran 4 mm, 8 mm, dan 17 mm yang kemudian diukur nilai perbedaan tekanan dan debilnya. Hasil penelitian menunjukkan bahwa nilai koefisien gesek aliran nanofluida A1203 sedikit lebih kecil dibandingkan dengan aliran air pada aliran turbulen. ......Nanofluid is a kind of the fluid that is being developed which has higher conductivity rather than the water. It needs advance research in studying the effects of the adding the nano particle to water, due to the friction coefficient when this fluid flows in straight pipe. This research done by flowing the water and nanofluid A1203 , with variation of flow velocity in different straight pipe which has diameter 4 mm, 8 mm, and I 7 mm then measure the head loss and capacity. The results showed that the friction coefficient of nanofluid al203 flow less than the water at the turbulent flow.

Abstrak :
Tujuan penelitian ini adalah melihat pengaruh aplikasi nano filled coating agent terhadap kekuatan tarik diametral semen ionomer kaca yang terkontaminasi saliva buatan. Spesimen direndam didalam aquabides selama 1 jam, 1 hari dan 1 minggu dengan suhu 37oC. Uji analisis statistik menggunakan t test tidak berpasangan. Hasil penelitian didapatkan pada perendaman 1 jam p= 0.051 dan 1 hari p=0,528 (P>0,05), sedangkan pada 1 minggu p=0.030 (p<0,05). Dapat disimpulkan bahwa aplikasi nano filled coating agent pada semen ionomer kaca yang terkontaminasi saliva buatan, sampai 1 hari dapat memberikan perubahan yang tidak bermakna pada nilai kekuatan tarik diametral.

---

The purpose of this study is to see the influence of nano-filled coating agent applications for diametral tensile strength of GIC contaminated with artificial saliva. Specimens were stored in aquabides for 1 hour, 1 day and 1 week at 37 °C. Test analysis using non-paired t test. The results obtained at 1 hour immersion p = 0051 and 1 day p = 0.528 (P> 0.05), whereas at 1 week p = 0030 (p <0.05). It can be concluded that the application of nano-filled coating agent on GIC contaminated with artificial saliva, until one day may provide a non-significant change in DTS values​​.

Abstrak :
Nanopartikel hybrid oksida besi/oksida tembaga/oksida seng telah disintesis dengan menggunakan metode sol-gel untuk tiga variasi molar. Seluruh sampel dikarakterisasi dengan spektroskopi X-Ray Diffraction, Field Emission Scanning Electron Microscopy, Vibrating Sample Magnetometer, Energy Dispersive X-Ray, Ultraviolet-visible Reflectance dan Fourier-Transform Infrared. Nanopartikel hybrid yang dihasilkan menunjukkan karakteristik feromagnetik dengan morfologi yang merupakan gabungan spherical-like dari oksida besi dan oksida seng dan clews-like dari oksida tembaga. Keempat unsur penyusunan nanopartikel hybrid hadir dalam bentuk ikatan Zn-O, Fe-O dan Cu-O dengan kehadiran fase dan struktur tunggal dari inverse cubic spinel magnetite, hexagonal wurtzite oksida seng dan monoclinic oksida tembaga. Celah energi nanopartikel hybrid cenderung turun dengan berkurangnya rasio molar oksida seng yang berhubungan dengan peningkatan kuantitas oksida besi dan oksida tembaga. Kondisi optimum aktivitas fotokatalitik nanopartikel hybrid dalam mendegradasi methylene blue dengan pemaparan cahaya ultraviolet diperoleh pada kondisi basa untuk pH 13. Nanopartikel hybrid dengan rasio molar 1:1:5 mampu menghasilkan degradasi maksimum dengan laju degradasi yang lebih tinggi dibandingkan nanopartikel oksida seng. Hole ditemukan sebagai spesies yang berperan aktif dalam aktivitas fotokatalitik nanopartikel hybrid dalam mendegradasi methylene blue. Iron oxide/cuprix oxide/zinc oxide hybrid nanoparticles with three variation of molar ratio have been synthesized using sol-gel methods. All samples were characterized by X-Ray Diffraction, Field Emission Scanning Electron Microscopy, Vibrating Sample Magnetometer, Energy Dispersive X-Ray, Ultraviolet-visible Reflectance and Fourier-Transform Infrared Spectroscopies. The resulting hybrid nanoparticles show ferromagnetic behaviour and have combination of spherical-like of iron oxide and zinc oxide morphologies with clews-like of cuprix oxide morphology. The four elements of the hybrid nanoparticles present in the form of Zn-O, Fe-O and Cu-O bonds and form individual crystal structures and phases of cubic inverse spinel of iron oxide, hexagonal wurtziteof zinc oxide and monoclinic of cuprix oxide. Energy gap of the hybrid nanoparticles tend to shift to lower energy that associates with increasing quantity of iron oxide and cuprix oxide with decreasing zinc oxide molar ratio. Optimum condition for photocatalytic activity of the hybrid nanoparticles in degrading methylene blue under ultraviolet light irradiation is obtained under alkaline conditions for pH 13. Hybrid nanoparticles with a molar ratio of 1:1:5 is able to produce the maximum degradation with higher degradation rate than zinc oxide nanoparticles. Hole found as species that plays an active role in photocatalytic activity of the hybrid nanoparticles to degrade methylene blue.

Abstrak :
Asam format telah dianggap sebagai senyawa kimia penyimpan hidrogen yang menjanjikan karena kandungan hidrogennya yang tinggi (4,4 wt%). Pada penelitian ini, nanopartikel berbasis logam PdNi dengan penambahan logam perak sebagai logam ketiga disintesis dan digunakan sebagai katalis untuk reaksi dehidrogenasi asam format. SiO2 nanosphere yang berperan sebagai penyangga, disintesis dengan menggunakan metode Stöber. Pendistribusian logam-logam ke permukaan penyangga dilakukan dengan menggunakan metode impregnasi basah dengan mencampurkan PdCl2, NiCl2.6H2O, dan AgNO3 dengan SiO2 nanosphere, yang dilanjutkan dengan reaksi reduksi menggunakan agen pereduksi NaBH4. Material yang dihasilkan dikarakterisasi dengan instrumen XRD, XRF, SAA, dan FESEM-EDX. Variasi komposisi logam perak yang ditambahkan ke dalam katalis berbasis PdNi/SiO2 NS dan suhu reaksi yang digunakan memengaruhi aktivitas katalitik dari nanopartikel logam. Uji aktivitas katalitik terhadap reaksi dehidrogenasi asam format dilakukan dengan menggunakan rangkaian alat buret gas. Jumlah gas yang dihasilkan diamati berdasarkan pergeseran air yang terjadi pada buret gas. Gas yang dihasilkan dikarakterisasi dengan instrumen GC-TCD. Katalis Pd0,4Ag0,6/SiO2 NS menunjukkan aktivitas katalitik yang baik dengan nilai TOF sebesar 312,68 jam-1 dan konversi sebesar 80,31% pada suhu reaksi 70°C. ......Formic acid has been considered a high-potential chemical hydrogen storage because of its high hydrogen density (4,4 wt%). In this study, PdNi nanoparticles with the addition of silver metal as a third metal were prepared as catalysts for formic acid dehydrogenation reactions. SiO2 nanospheres as a support were synthesized using the Stöber method. The distribution of metals to the support was carried out using the wet impregnation method by mixing PdCl2, NiCl2.6H2O, and AgNO3 with the SiO2 nanospheres followed by simultaneous reduction using NaBH4. The resulting materials were characterized using XRD, XRF, SAA, and FESEM-EDX. Variations in the composition of the silver metal added to the PdNi/SiO2 NS catalyst and the reaction temperature used in this study had affected the catalytic activity of the metal nanoparticles. The catalytic activity test for the formic acid dehydrogenation reaction was carried out using a gas burette. The amount of gas produced will be observed based on changes in the volume of water in the gas burette. The as-prepared Pd0,4Ag0,6/SiO2 NS shows outstanding catalytic activity for formic acid dehydrogenation with a TOF value of 312,68 h-1 and 80.31% conversion at 70°C.

Abstrak :
Tanaman sambiloto (Andrographis paniculate) adalah salah satu tanaman yang umum digunakan pada obat tradisional di Indonesia. Pada tanaman sambiloto, terdapat senyawa aktif yakni andorgrafolid. Senyawa andrografolid memiliki banyak aktivitas farmakologi termasuk aktivitas antivirus terhadap virus SARS-CoV-2. Namun, andrografolid memiliki kelemahan yakni rasanya yang pahit, sukar larut dalam air serta bioavailabilitas yang rendah. Sehingga, andrografolid perlu diformulasikan secara optimum guna dapat mengatasi kelemahan andrografolid. Penelitian ini bertujuan untuk memperoleh formulasi Nanostructured Lipid Carrier dengan kandungan andrografolid dengan karakteristik sesuai sediaan parenteral. Formulasi Nanostructured Lipid Carrier dibuat menggunakan zat aktif andrografolid, minyak kelapa sawit, minyak zaitun, gliserin, aquabidest serta variasi gliseril monostearat yakni 2%, 3%, 4%. NLC dibuat menggunakan alat homogenizer selanjutnya dilakukan pengurangan ukuran globul dengan ultrasonikasi amplitude 60% selama 12 menit. NLC diuji karakteristiknya meliputi ukuran globul, potensial zeta, indeks polidispersitas, viskositas, tegangan permukaan, morfologi globul, efisiensi penjerapan serta penetapan kadar. Pada penelitian ini memperlihatkan bahwa formula optimum yakni NLC dengan gliseril monostearate 2%. NLC yang diperoleh memenuhi kriteria sediaan rute parenteral yakni ukuran globul, indeks polidispersitas, zeta potensial, serta efisiensi penjerapan berturut-turut yakni 438,33 ± 90,71; 0,237 ± 0,01; -37,1 ± 0,34; 82,8890 ± 0,10% dan memiliki ukuran globul yakni sferis namun NLC masih belum memenuhi syarat sterilitas. Berdasarkan uji stabilitas yang dilakukan, NLC memiliki kestabilan fisik termasuk uji cucling, uji sentrifugasi, serta uji pada tiga kondisi suhu berbeda. Hasil penelitian yakni formula optimum NLC dengan GMS 2% memiliki kestabilan fisik baik hingga minggu ke-12. ......Sambiloto (Andrographis paniculata) is one of the plants used as traditional medicine in Indonesia. The active substance in Sambiloto, namely andrographolide, has many pharmacological activities. One of them is pharmacological activity against the SARS-CoV-2 virus. However, andrographolide has its limitation such as low solubility in water, low bioavailability, and bitter taste. Therefore, andrographolide needs to formulated optimally to overcome these limitation. This study aims to obtain formulation of nanostructured lipid carrier andrographolide with suitable characteristics for parenteral administration. The NLC formulation consisted of andrographolide, palm oil, olive oil, glycerin, and double-distilled water with variances of glyceryl monostearate 2%, 3%, 4%. The manufactured of NLC using a homogenizer was continued with 60% amplitude ultrasonication for 12 minutes. The test of NLC characteristics included globule size, polydispersity index, assay, viscosity, surface tension, globule morphology, encapsulation efficiency, and sterility test. The study showed that, the optimum formula NLC with 2% glyceryl monostearate. NLC met the criteria for the parenteral route of administration which is globul size, polydispersity index, zeta potensial and encapsulation efficiency, respectively, 438.33±90.71; 0.237±0.01; -37.1 ± 0.34; 82.889±0.10%, and spherical shaped globule but did not meet the requirements for sterility. In addition, the physical stability of NLC was also carried out including centrifugation test, cycling test, test at three different temperatures. This study showed that formula optimum NLC with GMS 2% also the results of the physical test showed that NLC had good physical stability until 12th week.

Abstrak :
This book gives an overview of nanostructures and nanomaterials applied in the fields of energy and organic electronics. It combines the knowledge from advanced deposition and processing methods of nanomaterials such as laser-based growth and nanopatterning and state-of-the-art characterization techniques with special emphasis on the optical, electrical, morphological, surface and mechanical properties. Furthermore it contains theoretical and experimental aspects for different types of nanomaterials such as nanoparticles, nanotubes and thin films for organic electronics applications.

Abstrak :
ABSTRAK
A natural-based nanocomposite film consisting of chitosan, montmorillonite (MMT) and cashew nut shell liquid (CNSL) was synthesized. The nanocomposite was prepared by mixing a suspension of clay particles (filler, MMT) with a solution containing chitosan as the macroscopic polymer matrix. In this study, it was proposed that non-ionic long-chain alkyl molecules with possible interact ions with the amine group of chitosan could be used as a plasticizer. As a natu-ral source for these compounds, an extract of CNSL was used. A series of chitosan/MMT com-posite samples containing two different clay contents and a sample with an additional CNSL were prepared. FTIR spectroscopy of the nanocomposite films indicated that, by addition of CNSL, amide groups of the chitosan are probably less attached and have more space for vibration. CNSL seems to provide in termolecular spaces between the chitosan molecules. Atomic force microscopy (AFM) analysis showed that the composite contained particles measuring 100 nm or less, which confirmed that the nanocomposite had been successfully produced by this method. Addition of CNSL as plasticizer improved the tensile strength by 10% and the elastic modulus by almost 18%. Cell growth was observed on all the nanocomposite samples studied.

Abstrak :
Nanocomposite thin films consisting of titanium oxide, or TiO2, nanoparticles embedded in apolymer matrix represent a new class of potential materials for optoelectronic applications such as optical switches, waveguides, high refractive indices and non-linear optical devices. Among the various processing techniques under development for these nanocomposites, the in situ sol−gel process is known to be versatile as it enables control of the inorganic-organic interaction at various molecular, nanometer, and micrometer scales. However, the sol−gel process has a major limitation, which is the low crystallinity in the resulting TiO2 phase due to relatively low processing temperatures. Therefore, the current research is aimed at investigating the nanostructural evolution of theTiO2 crystallite during the in situ sol−gel process to gain a better understanding of the mechanisms responsible for the largely amorphous nature of TiO2 nanoparticles. For this purpose, two sol−gel parameters, i.e., the hydrolysis ratio (Rw) and pH value of the TiO2 precursor solution were varied. On the basis of XRD and FTIR analyses, it was found that the largely amorphous TiO2 state is related to the fast development of stiff Ti−OH networks during the hydrolysis and condensation stag es of the sol−gel process, and concurrently worsened by the formation of the rigid PMMA matrix upon thermal annealing.

Abstrak :
Sebuah penelitian sistematis telah dilakukan untuk mengetahui penyebab utama rendahnya tingkat kristalinitas nanopartikel titania (TiO2) di dalam nanokomposit TiO2−PMMA hasil proses sol−gel. Dari hasil investigasi diketahui bahwa fasa TiO2 amorfus di dalam nanokomposit disebabkan oleh pembentukan cepat dari jaringan kaku Ti-OH selama tahapan hidrólisis dan kondensasi, yang diperburuk dengan efek perangkap dari matrik PMMA. Sebuah metode kombinasi pra-anil dan pasca-hidrotermal berhasil meningkatkan tingkat kristalinitas fasa TiO2 secara signifikan , dengan tetap mempertahankan integritas matrik polimer di dalam nanokomposit. Analisis evolusi nano struktural TiO2 dalam nanokomposit dilakukan dengan pengujian XRD, spektroskopi FTIR dan TEM. Peningkatan kristalinitas nanopartikel TiO2 meningkatkan sifat-sifat optis linier dan nonlinier lapisan tipis transparan nanokomposit TiO2−PMMA

---

A systematic investigation has been conducted to understand the mechanisms responsible for the low nanocrystallinity of TiO2 nanoparticles in sol−gel derived TiO2 −PMMA nanocomposites. On the basis of investigation, it is found that the largely amorphous TiO2 state is caused by the fast development of stiff Ti−OH networks during hydrolysis and condensation, worsened by the PMMA entrapment effect. A combined method involving a pre-annealing and a post -hydrothermal treatment has been successfully devised to enhance TiO2 nanocrystallinity, while maintaining the integrity of polymer matrix. The nanostructural evolution of TiO2 in nanocomposites were carried out with x-ray diffraction, Fourier Transfor Infra-Red (FTIR) spectroscopy and High -Resolution Transmission Microscope (HRTEM). The functional properties of the TiO2−PMMA nanohybrids have been correlated to their nanostructures, where both linear and nonlinear optical responses are shown to increase with the enhancement of TiO2 nanocrystallinity.