Hasil Pencarian  ::  Simpan CSV :: Kembali

"Bekisting merupakan salah satu komponen penting yang banyak digunakan khususnya pada konstruksi bangunan beton. Penggunaan kayu sebagai material penyusun bekisting masih sangat umum digunakan di Indonesia dan menimbulkan limbah konstruksi yang tidak dapat digunakan kembali. Dalam upaya mengurangi limbah kayu tersebut, pemanfaatan limbah plastik jenis HDPE (High-Density Polyethylene) sebagai bahan baku untuk produk bekisting dapat menjadi sebuah solusi. Penelitian ini mengamati pengaruh bukaan pada balok rangka polimer HDPE dan perbandingannya dengan balok solid tanpa bukaan. Dilakukan perbandingan analisa properti mekanik kuat lentur dari balok bekisting HDPE dengan metode DIC (Digital Image Correlation) dengan pemodelan numerik menggunakan ABAQUS.

---

Formwork is one of the essential components widely used, especially in concrete building construction. The use of wood as the material for formwork is still very common in Indonesia and generates construction waste that cannot be reused. In an effort to reduce wood waste, utilizing HDPE (High-Density Polyethylene) plastic waste as a raw material for formwork products can be a solution. This study observes the effect of openings in HDPE polymer truss beams and compares them with solid beams without openings. A comparison of the mechanical flexural properties of HDPE formwork beams is carried out using the DIC (Digital Image Correlation) method with numerical modeling using ABAQUS software."

"Bekisting yang merupakan penyumbang limbah konstruksi terbesar, dan sampah plastik di Indonesia yang terus meningkat tiap tahunnya memerlukan solusi penanganan yang tepat. Dapat digunakan limbah plastik jenis HDPE (High-Density Polyethylene) di Indonesia sebagai bahan baku untuk produk bekisting. Pada penelitian ini akan dilakukan perbandingan analisa properti mekanik kuat lentur balok bekisting HDPE dengan tambahan metode DIC (Digital Image Correlation) dengan pemodelan numerik menggunakan ABAQUS. Hasil dari penelitian ini diharapkan dapat memberikan solusi alternatif bahan bekisting dari HDPE yang kuat dan lebih ramah lingkungan.

---

Formwork, which is one of the largest contributors to construction waste, and plastic waste in Indonesia, which continues to increase every year, require appropriate handling solutions. HDPE (High-Density Polyethylene) waste in Indonesia can be used as raw material for formwork products. This study will compare the mechanical properties, specifically the flexural strength of HDPE formwork beams, using the Digital Image Correlation (DIC) method and numerical modeling with ABAQUS. The results of this study are expected to provide an alternative solution for formwork materials from HDPE that are strong and more environmentally friendly."

"Kekuatan tarik ultima, kekuatan tekan ultima, kekuatan lentur ultima, dan kekuatan geser lamina satu arah, bersama dengan kekuatan geser dan perilaku kelelahan laminate arah beragam, akan menjadi subjek utama dari studi ini. Untuk menciptakan bahan komposit yang berkelanjutan, serat rami, yang dikenal dengan kekuatan tarik yang sangat baik dan ramah lingkungan, akan dicampur dengan asam polilaktat (PLA) yang dapat terurai secara alami. Pengujian mekanis yang telah diatur sebelumnya akan menilai karakteristik tarik, tekan, lentur, dan geser komposit di bawah pengaturan yang terkontrol, mengungkapkan seberapa baik bahan tersebut dapat menahan tekanan yang umum dalam aplikasi prostetik. Kegunaan prostetik bergantung pada daya tahan bahan selama tekanan siklus, yang dapat diketahui dengan menganalisis perilaku kelelahan menggunakan penilaian kurva S-N. Diharapkan studi ini akan menunjukkan bahwa komposit Rami-PLA dapat digunakan sebagai pengganti yang layak dan efisien untuk prostetik anggota tubuh bawah, sehingga memajukan bidang teknologi prostetik.

---

The ultimate tensile strength, ultimate compressive strength, ultimate flexural strength, and shear strength of unidirectional lamina, along with the shear strength and fatigue behavior of multidirectional laminate, will be the main subjects of this investigation. To create a sustainable composite material, ramie fibers, known for their excellent tensile strength and environmental friendliness, will be mixed with biodegradable polylactic acid (PLA). Prearranged mechanical testing will assess the composite's tensile, compressive, flexural, and shear characteristics under controlled settings, revealing how well it can tolerate stresses common to prosthetic applications. Prosthetic usefulness depends on the material's durability during cyclic stress, which can be ascertained by analyzing the fatigue behavior using S-N curve assessments. It is anticipated that this study will show that Ramie-PLA composites could be used as a viable and efficient substitute for lower limb prosthetics, advancing the field of prosthetic technology."

"ABSTRACTPengujian beton dengan metode non destructive test sangat dibutuhkan dalam mengevaluasi kondisi beton pada konstruksi, guna mengurangi resiko kerugian akibat pengujian dengan metode destructive test. Skripsi ini membahas korelasi shearwave velocity dengan mutu beton. Penelitian ini adalah penelitian eksperimental dengan mencari nilai shearwave velocity dan mutu beton, yang kemudian dibandingkan dengan nilai longitudinal wave velocity. Nilai shearwave velocity didapatkan dari pengujian menggunakan bantuan alat A1040 MIRA dan longitudinal wave velocity didapatkan dari bantuan alat UPV. Pengujian dilakukan pada beton dengan mutu K225, K350, dan K500 selama 28 hari hingga lebih. Hasil dari penelitian ini menunjukan bahwa shearwave velocity pada beton berbanding lurus dengan mutu beton akan tetapi nilai shearwave velocity tidak mengikuti kenaikan kekuatan tekan beton, shearwave velocity cenderung bersifat stabil saat umur beton memasuki 10 hingga 14 hari.

---

ABSTRACTConcrete testing with non destructive test method is needed in evaluating the condition of concrete in construction, in order to reduce the risk of loss due to testing by destructive test method. This thesis discusses the correlation of shearwave velocity with the concrete strength. This research is an experimental research by looking for shearwave velocity and concrete strength, which is then compared with longitudinal wave velocity value. The shearwave velocity values were obtained from the test using the A1040 MIRA tool and longitudinal wave velocity were obtained from the test using the UPV tools. Tests were performed on concrete with quality K225, K350, and K500 for 28 days to over. The result of this research shows that shearwave velocity in concrete is directly proportional to the quality of concrete but the shearwave velocity does not follow the increase of concrete compressive strength for the same quality, shearwave velocity tends to be stable when the age of concrete enters 10 to 14 days."

"Objective: The aim of this study was to investigate the effect of immersion time in artificial saliva on the flexural strength of provisional crown and bridge (p-c&b) materials. Materials and Methods: Two types of p-c&b materials were used in this study: Light polymerized p-c&b material (Revotek LC) and autopolymerized p-c&b material (PerfecTemp II). A total of 100 specimens were fabricated and measured according to ISO 4049/2000. A stainless steel mould was used to prepare 2mm x 2mm x 25mm bar shaped specimens. All materials were dispensed and manipulated according to the manufacturers' instructions. The specimens were divided into 5 groups (n=10). Each specimen of the first group was measured immediately after preparation. The second, third, fourth and fifth groups were immersed in artificial saliva at 37°C in an incubator for 1 hour, 1 day, 7 days, 14 days, respectively. Flexural strength was tested by Universal Mechanical Testing Machine Shimadzu in a 3-point bending test. The Repeated ANOVA and Post-Hoc Bonferroni test were used to compare the continuous variables between the groups. Result: The results showed flexural strength of Revotek LC were higher than PerfecTemp II achieved the highest value in 7 days. Conclusion: Flexural strength of p-c&b materials were influenced by immersion time in artificial saliva and the type of p-c&b materials."

"Kemampuan beton dalam menahan tegangan tarik lebih kecil dibandingkan dalam menahan tegangan tekan. Kekuatan tarik ini dapat menimbulkan keretakan pada beton. Kuat tarik pada beton harus ditingkatkan dengan menggunakan serat kawat ke dalam campuran beton sejumlah proporsi berat terhadap semen. Pengujian tarik belah dan lentur dilakukan secara eksperimental dalam laboratorium. Untuk uji tarik belah dilakukan pada hari ke-7, 14, dan 28. Ukuran dari benda uji tarik belah yaitu silinder 15 x 30 cm. Pengujian lentur dilakukan menggunakan balok ukuran 15 x 15 x 60 cm. Spesimen diuji dengan konfigurasi lentur murni pada umur 14 dan 28 hari. Berbagai variasi serat kawat yang digunakan sebagai persentase volume untuk kadar semen yaitu 4%, 6%, 8%, 10%, dan 12%. Jenis serat kawat yang digunakan yaitu kawat bendrat. Hasil penelitian menunjukkan bahwa kemampuan menahan tarik dalam beton berserat mengalami peningkatan. Dari hasil pengujian, didapatkan bahwa variasi yang menunjukkan peningkatan paling besar yaitu 6%. Untuk kuat tarik belah terjadi peningkatan sebesar 36,89% dan untuk kuat lentur terjadi peningkatan sebesar 46,06%. Dengan menggunakan regresi polinomial, didapatkan persentase kadar maksimum yang lebih akurat. Untuk tes tarik belah kadar maksimum kawat bendrat sebesar 5,4 % dan untuk tes lentur sebesar 5,7%. Untuk perbandingan antara kuat tarik belah dengan kuat tekan beton dengan kawat bendrat menghasilkan koefisien perbandingan antara 0,480 ? 0,653. Sementara perbandingan antara kuat lentur dan kuat tekan beton kawat bendrat memiliki koefisien dalam kisaran 0,74 ? 1,07. Sedangkan perbandingan antara kuat tarik belah dan kuat lenturnya pada beton kawat bendrat memiliki koefisien antara 0,61 ? 0,65.

---

The capability of normal concrete to resist tensile stress is weaker than that of it to the compressive stress. As the capacity of tensile strength of concrete affect to the happening of crack growth, this tensile strength has to be improved by using some amount of steel fiber into concrete mixtures in weight proportion to the cement content. Splitting and flexural research has been conducted by set of laboratory experimental work. Testing speciments for splitting tensile tests performed at 7, 14, and 28 days. Size of cylinder speciment for splitting tensile test is 15 x 30 cm. A flexural research done to numbers of beam specimens size of 15x15x60 cm tested under pure bending configuration at the age of 14 and 28 days. Various proportions of steel fiber as volume percentage to cement content were chosen to be 4%, 6%, 8%, 10%, and 12% and the type of steel fiber is replaced by annealed wire. The research outcomes show that the capacity of this type of fibered concrete is physically improved.

From the result of test, it was found that the variation which shows maximum increase is 6%. For splitting test the increase is 36,89% and for flexural test has 46,06% increase. Polynomial regression can found the maximum percentage more accurately. By using this, we found for splitting tensile strength, the maximum percentage is 5,4% and for flexural test, we found that maximum percentage is 5,7%. For comparison between splitting test and compressive strength of steel fiber concrete has coeffiecient 0,480 ? 0,653. While the comparison between flexural test and compressive strength has coefficient 0,74 ? 1,07. Then, for comparison bertween splitting test and flexural test of steel fiber concrete has coefficient between 0,61 to 0,65."

"ABSTRAKLatar Belakang : Ekstrak Biji AnggurEBA mengandung proantosianidin sebagai pengikat silang kolagen yang menentukan sifat mekanik dentin.Tujuan : Menganalisis pengaruh larutan EBA terhadap kekuatan lentur dentin saluran akar.Metode : 90 lempeng dentin saluran akar dibagi menjadi 3 kelompok direndam larutan EBA, NaOCl dan aquabides. Dilakukan uji kekuatan lentur dentin dengan Universal Testing Machine.Hasil : Kekuatan lentur tertinggi pada kelompok larutan EBA, terendah pada kelompok NaOCl. Tidak terdapat perbedaan bermakna antara kelompok larutan EBA dan aquabides (p>0.05).Kesimpulan : Nilai kekuatan lentur dentin saluran akar pada larutan EBA lebih tinggi dibandingan dengan larutan NaOCl.

---

ABSTRACT

Background : Grape Seed Extract (GSE) contains proanthocyanidin as collagen crosslinking which determines the mechanical properties of dentin.

Objective: To analyze the effect of the GSE solution to the flexural strength of root canal dentin.

Methods : 90 root canal dentin slabs were divided into 3 groups, immersed in GSE solution , NaOCl and aquabidest . Dentin flexural strength test measured by Universal Testing Machine.

Results : The highest flexural strength was found in GSE solution group , the lowest in the group of NaOCl . There were no significant differences between GSE groups and aquabidest group ( p > 0.05 ).

Conclusion : The value of flexural strength of root canal dentin found in GSE solution group was higher when compared with NaOCl solution."

"The oral health of denture wearers depends on the cleanliness of their denture. Therefore, it needs proper care and maintenance to prolong the denture wearing, while the oral mucosa is kept healthy. Maintenance and cleaning the denture by brushing and immersing in desinfectant solution is done to eliminate microorganims. Themoplastic nylon is widely used as material of choice in constructing partial or full denture instead of acrylic resin heat-cured material. This material is superior due to good esthetic, thinner denture base compared with acrylic resin denture base, and alternative material for patient allergic to acrylic monomer. Based on findings, immersion in disinfectant solution for 24 hours can increase the rigidity of nylon denture base material. Refer to those, a research was done to discover the effect of chlorhexidine gluconate 0,2% and sodium hypoclorite 1% disinfectant solution to flexural strength of thermoplastic nylon material, bearing in mind that a those solution are available abundantly in less price. ln this research it is concluded that flexural strength of thermoplastic nylon material is increased in sodium hypochlorite 1% immersion compared to chlorhexidine gluconate 0,2%, aquadest immersion, and control group. Flexural strength of thermoplastic nylon material in chlorhexidine gluconate 0,2% and aquadest immersion are relatively equal. (p=1,000). Hereby disinfectant solution could effect to flexural strength of thermoplastic nylon material. Chlorhexidine gluconate 0,2% and aquadest immersion can decrease flexural strength compared to control group (p=0,000). Anticipation on physical, mechanical, and chemical changes of denture made from thermoplastic nylon material rises a need of socialization among dentist that thermoplastic nylon material can change at immersion in sodium Hypochlorite 1% and chlorhexidine gluconate 0,2% solution. To this matter, further research of other disinfectant solutions needs to be done."

"Latar Belakang: Palfique Universal Flow® merupakan resin komposit flowable yang digunakan untuk merestorasi gigi anterior dan posterior. Untuk dapat beredar di pasaran, material restorasi harus memenuhi karakteristik standar, salah satunya adalah kekuatan fleksural. Material restorasi akan terpapar oleh lingkungan mulut yang kondisi pH-nya selalu berubah sehingga dapat berdampak pada kekuatan fleksuralnya. Tujuan: Menganalisis pengaruh perendaman resin komposit supra-nano Palfique Universal Flow® tipe medium pada berbagai pH saliva buatan terhadap kekuatan fleksural. Metode: Sejumlah dua puluh empat spesimen resin komposit supra-nano Palfique Universal Flow® tipe medium dengan dimensi 25 x 2,8 x 2 mm dikelompokkan menjadi empat, yaitu kelompok tanpa perlakuan, perendaman di saliva buatan pH 3, pH 5,5, dan pH 7. Setelah direndam selama 7 hari, kekuatan fleksural diukur menggunakan Universal Testing Machine. Data dianalisis menggunakan uji Kruskal Wallis, Mann-Whitney, dan Independent T-Test. Hasil: Nilai kekuatan fleksural pada kelompok tanpa perlakuan merupakan yang tertinggi dan semakin rendah pada perendaman di dalam saliva buatan pH 7; 5,5; dan 3 secara berturut-turut dengan perbedaan signifikan (p≤0,05). Nilai antar kelompok berbeda signifikan pada seluruh kelompok (p≤0,05), kecuali pada pH 3 dengan pH 5,5 dan pH 5,5 dengan pH 7 (p>0,05). Kesimpulan: Saliva buatan yang asam menyebabkan nilai kekuatan fleksural resin komposit supra-nano Palfique Universal Flow® tipe medium menjadi lebih rendah.

---

Background: Palfique Universal Flow® is a flowable composite resin that used for restoring both anterior and posterior teeth. To be marketed, restorative materials must meet standard characteristics, one of which is flexural strength. Restorative materials are exposed to the oral environment, where pH conditions continuously change, potentially affecting their flexural strength. Objective: To analyze the effect of immersion medium-type supra-nano composite resin Palfique Universal Flow®in artificial saliva at various pH levels on the flexural strength. Methods: Twenty-four specimens of medium-type supra-nano composite resin Palfique Universal Flow®, with dimensions of 25 x 2.8 x 2 mm, divided into four groups: untreated, immersion in artificial saliva with pH 3, pH 5.5, and pH 7. After a 7-days immersion, the flexural strength was measured using a Universal Testing Machine. The data were analyzed using Kruskal-Wallis, Mann-Whitney, and Independent T-Test. Results: The flexural strength values in the untreated group were the highest, decreasing within immersion in artificial saliva at pH 7, 5.5, and 3 with significant differences observed (p≤0.05). Significant differences were noted between groups in all cases (p≤0.05), except between pH 3 and pH 5.5, as well as between pH 5.5 and pH 7 (p>0.05). Conclusion: Artificial saliva with acidic pH levels leads to lower flexural strength values of the medium-type supra-nano composite resin Palfique Universal Flow®.

"

"Skripsi ini membahas mengenai perilaku lentur papan laminasi dengan bahan karton minuman daur ulang yang menggunakan perekat urea formaldehida. Tujuan dari penelitian ini adalah untuk menentukan alternatif untuk mendaur ulang bahan-bahan dengan membuat papan dari cacahan karton aseptik yang akan dilaminasi menggunakan perekat urea formaldehida dan untuk mengetahui perilaku lenturnya. Dalam membuat papan panel, cacahan karton aseptik dicampur dengan 0%, 2,5%, 5%, dan 7,5% phenol formaldehida dan kemudian dikompresi dengan tekanan 25 kg/cm2 dan dipanaskan pada 170°C. Hal ini dihasilkan panel dengan phenol formaldehida 0% memberikan kuat lentur terbaik. Panel-panel tersebut kemudian direkatkan dengan urea formaldehida, untuk membuat papan dua lapisan dengan masing-masing ketebalan 10 mm dan tiga papan lapisan masing-masing dengan ketebalan 8 mm. Papan berlapis tersebut kemudian dibandingkan dengan yang dilem dengan epoksi sebagai perekat dingin dalam hal sifat mekanik yaitu modulus elastisitas (MOE) dan modulus pecah (MOR). Pengujian prosedur sifat fisik dan mekanik dilakukan dengan menggunakan standar JIS A 5908: 2003 dan ASTM C 580-02. Hasil dari penelitian nilai MOE dan MOR papan laminasi aseptik menggunakan perekat urea formaldehida lebih tinggi dari papan laminasi dengan perekat dingin epoksi.

---

This final project discussed the flexural behavior of recycle beverage carton lamina using urea formaldehide adhesive. The objectives of this research were to determine an alternative to recycle those materials by making shredded aseptic carton laminated board using urea formaldehide adhesive and to find out its flexural behavior. In making panel board, shredded aseptic cartons were mixed with 0%, 2.5%, 5%, and 7.5% phenol formaldehyde and later compressed with a pressure of 25 kg/cm2 and heated under 170°C. It is found that panel with 0% phenol formaldehyde gave the best flexural strength. Those panels were then glued with urea formaldehyde, in order to make a two layers board containing each with 10 mm thickness and a three layers board each with 8 mm thickness. Those layered boards were then compared to those glued with epoxy as cold adhesive, in term of mechanical properties of modulus of elasticity (MOE) and modulus of rupture (MOR). Testing procedures of physical and mechanical properties were performed by using standard JIS A 5908: 2003 and ASTM C 580-02. MOE and MOR values of aseptic laminated board using urea formaldehyde adhesive was higher than those with a epoxy adhesive."