Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 178088 dokumen yang sesuai dengan query
cover
Kayzhea Qay
"Limbah fenol seringkali mencemari air dan tanah, mengakibatkan pencemaran yang merugikan bagi ekosistem serta menyebabkan risiko serius terhadap kesehatan manusia. Metode elektrolisis plasma adalah salah satu cara efektif untuk menanggulangi masalah limbah ini. Penelitian ini bertujuan untuk menganalisis pengaruh variasi daya pada tegangan tetap, konsentrasi awal limbah, dan penggunaan elektroda stainless steel SS-316 terhadap efektivitas proses yang meliputi fenomena pembentukkan plasma, degradasi limbah fenol, dan ketergerusan anoda. Dalam penelitian ini, udara diinjeksikan melalui katoda menggunakan lengkungan yang akan mengarahkan udara langsung ke zona terbentuknya plasma di anoda. Penelitian dilakukan dengan reaktor 1,2 L menggunakan variasi daya 250 W, 300 W, dan 350 W; dan variasi konsentrasi awal limbah 100 ppm, 200 ppm, dan 300 ppm W dengan elektrolit K2SO4 0,02 M. Pada penelitian ini, didapat hasil degradasi yang lebih baik oleh elektroda stainless steel dibandingkan tungsten. Selama 30 menit, SS-316 mampu mendegradasi fenol hingga 99% sedangkan tungsten hanya mencapai 84%. Sementara itu, ketergerusan tungsten jauh lebih besar dibandingkan SS-316. Pada percobaan ini, hasil degradasi tertinggi mencapai 99,9% yang didapat pada kondisi 350 W, konsentrasi limbah fenol 100 ppm, tegangan 550 V, dan dengan penambahan Fe2+ 20 ppm. Pada kondisi optimum ini juga didapatkan penurunan COD sebesar 85,65% dan terdapat produk samping berupa amonia sebesar 5,25 mmol dan nitrat sebesar 0,34 mmol yang terukur pada menit ke-30.

Phenolic waste often pollutes the air and soil, resulting in pollution that is detrimental to ecosystems and poses serious risks to human health. The plasma electrolysis method is one effective way to overcome this waste problem. This research aims to determine the effect of power variations at a fixed voltage, initial waste concentration, and the use of SS-316 stainless steel electrodes on the effectiveness of the process which includes plasma formation phenomena, phenol waste degradation, and anode erosion. In this research, air is injected through the cathode using an arch that will direct the air directly to the plasma formation zone at the anode. The research was carried out with a 1.2 L reactor using power variations of 250 W, 300 W, and 350 W; and variations in initial waste concentration of 100 ppm, 200 ppm, and 300 ppm W with 0.02 M K2SO4 electrolyte. In this research, better degradation results were obtained by stainless steel electrodes compared to tungsten. For 30 minutes, SS-316 was able to degrade phenol up to 99% while tungsten only reached 84%. Meanwhile, the abrasiveness of tungsten is much greater than that of SS-316. In this experiment, the highest degradation results reached 99.9% which were obtained under conditions of 350 W, waste phenol concentration of 100 ppm, voltage of 550 V, and with the addition of Fe2+ 20 ppm. Under these optimum conditions, COD was also reduced by 85.65% and there were by-products in the form of ammonia of 5.25 mmol and nitrate of 0.34 mmol as measured at the 30th minute."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Novy Cendian
"Industri batik di Indonesia kerap menghasilkan limbah cair yang mengandung zat pewarna yang tinggi dengan sifat yang toksik dan karsinogenik, tetapi dibuang langsung ke lingkungan tanpa diolah dahulu. Penghilangan zat pewarna tersebut dilakukan menggunakan elektrolisis plasma yang terbukti dan dipercaya sebagai metode yang efisien untuk mendegradasi limbah zat pewarna dengan kemampuan produksi OH yang lebih besar dari pada metode lainnya. Penelitian dilakukan dengan membangkitkan plasma menggunakan katoda stainless steel dan anoda tungsten yang tercelup sedalam 2 cm di larutan elektrolit Na2SO4 0,02 M dan pewarna Remazol Red dengan penambahan 20 mg/L ion Fe2+ dalam reaktor dengan aliran sirkulasi yang dapat memberikan pengadukan dan cakupan volume lebih besar. Daya operasi dijaga konstan saat menyelidiki pengaruh variasi laju injeksi udara dan konsentrasi awal limbah. Hasil yang diperoleh menunjukkan bahwa 1 L/min adalah laju injeksi udara optimum untuk dapat mengoperasikan reaktor ini secara efektif pada daya operasi optimum 450 W agar dapat menurunkan tegangan breakdown, mengurangi konsumsi energi, meningkatkan produksi OH dan spesi reaktif lainnya, dan meningkatkan persentase degradasi. Adapun konsentrasi awal limbah yang optimum ialah saat konsentrasinya paling rendah yakni sebesar 100 mg/L. Eksperimen pada kondisi operasi optimum selama 90 menit menghasilkan persentase degradasi mencapai 99,72% dengan energi spesifik sebesar 3177,16 kJ/mmol yang menyisakan konsentrasi Remazol Red sebesar 0,28 mg/L, COD sebesar 35,3 mg/L, dan senyawa intermediate berupa asam karboksilat dan keton.

Batik industry in Indonesia frequently dispose liquid waste containing high level of toxic and carcinogenic dyes to the drainage without being treated. The removal of dyes use plasma electrolysis which has been proved as the efficient method to degrade dyes waste, yielding higher hydroxyl radicals than other methods. The experiment was conducted by generating plasma in circulated reactor using stainless steel cathode and tungsten anode with 2 cm depth immersed in 0.02 M Na2SO4 electrolyte solution added by Remazol Red dyes and 20 mg/L Fe+ with addition of varying air injection rate and initial waste concentration at 450 W maintained power. The results conclude that 1 L/min is the  optimum air injection rate value to operate this reactor effectively at 450 W of optimum operating power so that it could lower the breakdown voltage, reduce energy consumption, produce more OH radicals and other reactive species, and elevate the degradation percentage. And the lowest value of Remazol Red concentration at 100 mg/L is concluded as the optimum initial dye concentration value. The experiment conducted in optimum condition provide result in 99.72% of degradation percentage and 3177.16 kJ of energy specific for 90 minutes with final concentation of dye is 0.29 mg/L, 35.3 mg/L of COD, and intermediate products such as carboxylic acid and ketone."
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Bening Farawan
"Limbah fenol dan logam Cr(VI) merupakan dua jenis limbah industri yang sering ditemukan sebagai kontaminan limbah cair yang berbahaya serta sulit untuk didegradasi. Melalui penelitian ini, fenol dan Cr(VI) didegradasi secara bersamaan menggunakan reaktor elektrolisis plasma yang dilengkapi dengan titanium sebagai plasma anoda oleh spesies reaktif seperti radikal •OH, radikal •H dan molekul H2O2. Untuk efisiensi energi, injeksi udara diterapkan ke zona elektrolisis plasma, yang berkontribusi pada pembentukan spesies radikal. Penelitian ini bertujuan untuk mengetahui pengaruh variasi laju aliran injeksi udara, daya dan tegangan yang berkorelasi dengan persentase degradasi fenol-Cr(VI) serta konsumsi energi spesifiknya. Hasil penelitian menunjukkan kondisi operasi maksimum elektrolisis plasma dicapai pada laju injeksi udara 0,2 LPM; daya 330 W; tegangan 600 V; konsentrasi elektrolit 0,02 M Na2SO4. Dalam waktu 30 menit, fenol terdegradasi sebanyak 54% dan Cr(VI) tereduksi seluruhnya dengan konsumsi energi spesifik sebesar 100.888 kJ/mmol. Efek penambahan injeksi udara kedalam zona plasma akan berdampak terhadap penambahan jenis spesi reaktif dan mengurangi konsumsi energi, sedangkan peningkatan tegangan operasi akan mempengaruhi rasio spesi reaktif yang dihasilkan, sementara efek terhadap peningkatan daya operasi akan menambah jumlah dari radikal •OH, radikal •H dan molekul H2O2. Temuan dalam penelitian ini akan sangat membantu untuk menghilangkan polutan organik dan anorganik secara bersamaan dalam air limbah yang kompleks.

Phenols and Cr(VI) are hazardous organic and heavy metal wastes produced from various industrial processes such as textile, paint, and electroplating. Through this research, phenol and Cr(VI) were degraded simultaneously using the plasma electrolysis reactor equipped with titanium as anode plasma by reactive species such as •OH radicals, •H radicals and H2O2 molecules. For energy efficiency, air injection is applied into the plasma electrolysis zone, which contributes to the formation of radical species. This research aims to obtain the effect of variations in the flow rate of air injection volatge and electrical power correlated with the percentage of phenol-Cr(VI) degradation and their specific energy consumption. The results showed maximum operating conditions of plasma electrolysis is achieved on the air injection rate of 0.2 LPM; 600 V; 330 W; and the electrolyte solution 0.02 M Na2SO4. Phenol degraded to 54% and Cr(VI) was degraded to 100% with a specific energy of 100.888 kJ/mmol within 30 minutes. The effect of adding air injection into the plasma zone will have an impact on the addition of reactive species and reduce energy consumption, while the increase in operating voltage will affect the ratio of reactive species produced, and the effect on increasing operating power will increase the number of radicals •OH, •H and H2O2. The findings in this research would be helpful for removing organic and inorganic pollutants simultaneously in complex wastewater."
Depok: Fakultas Teknik Universitas Indonesia, 2021
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Bening Farawan
"Limbah fenol dan logam Cr(VI) merupakan dua jenis limbah industri yang sering
ditemukan sebagai kontaminan limbah cair yang berbahaya serta sulit untuk didegradasi.
Melalui penelitian ini, fenol dan Cr(VI) didegradasi secara bersamaan menggunakan
reaktor elektrolisis plasma yang dilengkapi dengan titanium sebagai plasma anoda oleh
spesies reaktif seperti radikal •OH, radikal •H dan molekul H2O2. Untuk efisiensi energi,
injeksi udara diterapkan ke zona elektrolisis plasma, yang berkontribusi pada
pembentukan spesies radikal. Penelitian ini bertujuan untuk mengetahui pengaruh variasi
laju aliran injeksi udara, daya dan tegangan yang berkorelasi dengan persentase degradasi
fenol-Cr(VI) serta konsumsi energi spesifiknya. Hasil penelitian menunjukkan kondisi
operasi maksimum elektrolisis plasma dicapai pada laju injeksi udara 0,2 LPM; daya 330
W; tegangan 600 V; konsentrasi elektrolit 0,02 M Na2SO4. Dalam waktu 30 menit, fenol
terdegradasi sebanyak 54% dan Cr(VI) tereduksi seluruhnya dengan konsumsi energi
spesifik sebesar 100.888 kJ/mmol. Efek penambahan injeksi udara kedalam zona plasma
akan berdampak terhadap penambahan jenis spesi reaktif dan mengurangi konsumsi
energi, sedangkan peningkatan tegangan operasi akan mempengaruhi rasio spesi reaktif
yang dihasilkan, sementara efek terhadap peningkatan daya operasi akan menambah
jumlah dari radikal •OH, radikal •H dan molekul H2O2. Temuan dalam penelitian ini akan
sangat membantu untuk menghilangkan polutan organik dan anorganik secara bersamaan
dalam air limbah yang kompleks.

Phenols and Cr(VI) are hazardous organic and heavy metal wastes produced from various
industrial processes such as textile, paint, and electroplating. Through this research,
phenol and Cr(VI) were degraded simultaneously using the plasma electrolysis reactor
equipped with titanium as anode plasma by reactive species such as •OH radicals, •H
radicals and H2O2 molecules. For energy efficiency, air injection is applied into the
plasma electrolysis zone, which contributes to the formation of radical species. This
research aims to obtain the effect of variations in the flow rate of air injection volatge and
electrical power correlated with the percentage of phenol-Cr(VI) degradation and their
specific energy consumption. The results showed maximum operating conditions of
plasma electrolysis is achieved on the air injection rate of 0.2 LPM; 600 V; 330 W; and
the electrolyte solution 0.02 M Na2SO4. Phenol degraded to 54% and Cr(VI) was
degraded to 100% with a specific energy of 100.888 kJ/mmol within 30 minutes. The
effect of adding air injection into the plasma zone will have an impact on the addition of
reactive species and reduce energy consumption, while the increase in operating voltage
will affect the ratio of reactive species produced, and the effect on increasing operating
power will increase the number of radicals •OH, •H and H2O2. The findings in this
research would be helpful for removing organic and inorganic pollutants simultaneously
in complex wastewater.
"
Depok: Fakultas Teknik Universitas Indonesia , 2021
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Aldela Verlinika Devani
"Limbah fenol merupakan limbah berbahaya dan sulit terdegradasi yang ditemukan di berbagai industri, seperti petrokimia, tekstil, dan lainnya. Pada penelitian ini, limbah fenol akan didegradasi menggunakan metode elektrolisis plasma injeksi udara dengan katoda sebagai injektor. Penelitian ini bertujuan untuk mengkaji pengaruh laju alir udara dan tegangan untuk mendapatkan kondisi optimum elektrolisis plasma. Selain itu, dilakukan penambahan zat warna Remazol Red dalam larutan fenol untuk mengetahui kinerja elektrolisis plasma dalam mendegradasi limbah campuran. Parameter efektivitas proses degradasi limbah fenol akan ditinjau berdasarkan energi pembentukan plasma, persentase degradasi limbah fenol, dan erosi anoda. Penelitian dilakukan dengan reaktor 1,2 L menggunakan variasi laju injeksi udara 0 L/min; 0,2 L/min; 0,3 L/min, dan 0,4 L/min serta variasi tegangan 550 V, 600 V, dan 650 V dengan larutan elektrolit K2SO4 0,02 M. Berdasarkan penelitian, diketahui bahwa penambahan zat pewarna Remazol Red tidak menurunkan persentase degradasi limbah fenol. Penambahan laju alir injeksi udara hingga titik optimum (0,3 L/min) dapat meningkatkan persentase degradasi limbah fenol. Tegangan optimum pada penelitian ini adalah 550 V. Tegangan lebih tinggi akan meningkatkan persentase degradasi limbah fenol dan erosi anoda. Hasil degradasi fenol pada kondisi optimum mencapai 99,88% dengan erosi anoda 0,02 g dan penurunan kadar COD mencapai 80,38% pada konsentrasi awal limbah fenol 100 ppm dan FeSO4 20 ppm. Produksi senyawa samping yang didapat berupa nitrat sebesar 5,958 mmol dan amonia sebesar 0,529 mmol. 

Phenol waste is a dangerous and difficult to degrade waste that is found in various industries, such as petrochemical, textile, and others. In this research, phenol waste will be degraded using the air injection plasma electrolysis method with the cathode as the injector. This research aims to examine the influence of air flow rate and voltage to obtain optimum conditions for plasma electrolysis. In addition, Remazol Red dye was added to the phenol solution to determine the performance of plasma electrolysis in degrading mixed waste. The effectiveness parameters of the phenol waste degradation process will be reviewed based on plasma formation energy, percentage of phenol waste degradation, and anode erosion. The research was carried out with a 1,2 L reactor using varying air injection rates of 0 L/min; 0,2 L/min; 0,3 L/min, and 0,4 L/min and voltage variations of 550 V, 600 V, and 650 V with 0,02 M K2SO4 electrolyte solution. Based on research, it is known that the addition of Remazol Red dye does not reduce the percentage of waste degradation phenol. Increasing the air injection flow rate to the optimum point (0,3 L/min) can increase the percentage of phenol waste degradation. The optimum voltage in this study was 550 V. A higher voltage will increase the percentage of phenol waste degradation, but will increase anode erosion. The results of phenol degradation under optimum conditions reached 99,88% with anode erosion of 0.02 g and the reduction in COD levels reached 80,38% at an initial phenol waste concentration of 100 ppm and FeSO4 20 ppm. The side compound production obtained was nitrate of 5,958 mmol and ammonia of 0,529 mmol."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Tamima Nurindra Prameswari
"Fenol dan Cr(VI) merupakan salah satu limbah organik dan anorganik yang memiliki tingkat toksisitas yang tinggi dikarenakan sifatnya yang beracun sehingga dapat menimbulkan efek buruk bagi kesehatan manusia dan lingkungan. Untuk itu diperlukan sebuah pengolahan limbah simultan yang dapat mendegradasi limbah agar dapat aman jika diteruskan ke lingkungan. Teknologi untuk mengolah kembali limbah tersebut ialah teknologi elektrolisis plasma. Pengujian dengan kondisi optimum diperlukan agar dapat mengetahui kondisi yang optimal dalam mendegradasi limbah Fenol dan Cr(VI). Dengan menguji konsentrasi awal limbah fenol, penambahan aditif Fe2+ dan adanya injeksi udara. Degradasi limbah berhasil terukur dengan alat Spektrofotometer UV-VIS dengan kondisi optimum limbah awal Fenol 400 ppm, limbah awal Cr(VI) 100 ppm, konsentrasi Fe2+ 30 ppm, injeksi udara 0.4 L/min, Na2SO4 0.01 M pada tegangan 650 V selama 120 menit menghasilkan persentase degradasi limbah fenol sebesar 61,7% dan limbah Cr(VI) sebesar 97%. Nilai mmol terdegradasi untuk limbah fenol sebesar 1,639 mmol dan limbah Cr(VI) sebesar 0,961 mmol. Serta konsumsi energi 3467,88 kJ dan energi spesifik 1333,80 kJ/mmol.

Phenol and Cr(VI) are one of the organic and inorganic wastes that have a high level of toxicity due to their toxic nature so that they can cause adverse effects on human health and the environment. For this reason, a simultaneous waste treatment is needed that can degrade waste so that it can be safely forwarded to the environment. The technology for reprocessing the waste is plasma electrolysis technology. Testing with optimum conditions is needed in order to determine the optimal conditions in degrading Phenol and Cr(VI) waste. By testing the initial concentration of phenol waste, the addition of Fe2+ additives and the presence of air injection. Waste degradation was successfully measured using a UV-VIS Spectrophotometer with optimum conditions for initial waste Phenol 400 ppm, initial waste Cr(VI) 100 ppm, Fe2+ concentration 30 ppm, air injection 0.4 L/min, Na2SO4 0.01 M at a voltage of 650 V for 120 minutes resulted in the percentage of phenol waste degradation of 61.7% and Cr(VI) waste of 97%. The degraded mmol value for phenol waste is 1.639 mmol and Cr(VI) waste is 0.961 mmol. And energy consumption is 3467.88 kJ and specific energy is 1333.80 kJ/mmol"
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Amanda Vania Tjendana
"Limbah fenol dan logam Cr(VI) merupakan limbah organik dan logam berat berbahaya dan sulit didegradasi. Kedua jenis limbah tersebut dihasilkan dari berbagai macam proses industri seperti industri tekstil, cat, pewarna, dan lain lain. Maka, diperlukan teknologi pengolahan limbah yang efektif, salah satunya adalah dengan teknologi Contact Glow Discharge Electrolysis (CGDE). Metode Cathodic Contact Glow Discharge Electrolysis adalah bagian dari teknologi CGDE, dimana plasma terbentuk di katoda dengan pancaran sinar yang terang (glow discharge). Metode ini dapat menghasilkan spesi reaktif •OH dan H• dalam jumlah besar sehingga mampu mendegradasi limbah cair fenol dan Cr(VI) secara simultan. Kondisi optimum yang didapatkan adalah pada konsentrasi awal Cr(VI) 100 ppm, konsentrasi elektrolit Na2SO4 0,02 M, dan laju alir udara 0,2 L/menit. Untuk plasma anodik, didapatkan persentase degradasi untuk fenol sebesar 99,7% dan Cr(VI) sebesar 49%. Sedangkan untuk plasma katodik didapatkan persentase degradasi untuk fenol sebesar 70,98% dan Cr(VI) sebesar 44,77% selama 120 menit proses CGDE.

Phenol waste and Cr(VI) metal are hazardous organic waste and heavy metals that are difficult to degrade. Both types of waste are generated from various industrial processes such as textile, paint, dye, and so on. Therefore, an effective waste treatment technology is needed, one of which is Contact Glow Discharge Electrolysis technology. Cathodic Contact Glow Discharge Electrolysis is a part of plasma electrolysis technology in which plasma is formed at cathode with a bright glow (glow discharge). This method produces large quantity of reactive species •OH and H• which can degrade phenol and Cr(VI) liquid waste simultaneously. The optimum conditions obtained were at the initial concentration of Cr (VI) 100 ppm, electrolyte Na2SO4 0.02 M, and air flow rate of 0.2 L/minute. For anodic CGDE, the percetage for phenol degradation was valued at 99.7% and Cr(VI) degradation was valued at 49%. Whereas for the cathodic CGDE, the percentage for phenol degradation was valued at 70.98% and Cr(VI) degradation was valued at 44.77% for 120 minutes of plasma electrolysis process."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Tulus Sukreni
"Proses elektrolisis plasma yang merupakan bagian dari Advanced Oxidation Process (AOP) sangat efektif digunakan untuk degradasi limbah pewarna tekstil. Energi yang dihasilkan selama proses tersebut dapat membentuk oksidan-oksidan yang sangat reaktif, terutama radikal hidroksil, yang dapat mendegradasi senyawa-senyawa dalam limbah pewarna tekstil. Namun, proses ini membutuhkan konsumsi energi yang tinggi untuk pembentukan plasma. Selain itu radikal hidroksil (●OH) yang dihasilkan merupakan oksidator yang bersifat non selektif. Oleh karena itu, untuk meningkatkan efisiensi proses, pada penelitian ini dilakukan variasi beberapa parameter yang berpengaruh terhadap proses elektrolisis plasma seperti konsentrasi dan suhu larutan, posisi kedalaman anoda, serta laju alir volume udara injeksi. Penambahan kedalaman posisi anoda dari 5 mm ke 65 mm menunjukkan peningkatan konsumsi energi sebesar 41,95%. Sementara injeksi udara dengan laju alir volume 6 L/menit dapat menurunkan energi pembentukan plasma sebesar 33,48% bila dibandingkan dengan energi pembentukan plasma tanpa injeksi udara. Variasi parameter-parameter tersebut juga berpengaruh terhadap produksi radikal hidroksil. Peningkatan jumlah radikal hidroksil diperoleh pada posisi anoda yang semakin dalam, serta laju alir udara yang rendah yaitu kurang dari 2 L/menit. Pada laju alir volume yang tinggi, penurunan konsumsi energi yang terjadi berdampak pada penurunan produksi radikal hidroksil dimana semakin tinggi laju injeksi udara, radikal hidroksil yang dihasilkan semakin rendah. Proses degradasi Remazol Red sebagai pewarna tekstil juga dipengaruhi oleh laju alir volume udara injeksi. Pada kondisi laju alir volume udara yang optimum, yaitu 0,05 L/menit, diperoleh degradasi pewarna tekstil sebesar 96,04%, meningkat 39,76% jika dibandingkan dengan proses degradasi tanpa injeksi udara.

The plasma electrolysis process which is part of the Advanced Oxidation Process (AOP) is effectively used for the degradation of textile dye waste. The energy generated during the process can form highly reactive oxidants, especially hydroxyl radicals, which can degrade the compounds in textile dye wastes. However, this process requires high energy consumption for plasma formation. In addition, the hydroxyl radicals (●OH) produced are non selective oxidizer. Therefore, to improve the efficiency of the process, the variation of several parameters in this research which influenced the plasma electrolytic processes were carried out such as concentration and temperature of the solution, the depth of the anode, and the volume flow rate of air injection. The addition of the anode position depth from 5 mm to 65 mm showed an increase in energy consumption of 41.95%. While air injection with a volume flow rate of 6 L/minute can reduce plasma formation energy by 33.48% when compared to the energy of plasma formation without air injection. The variation of these parameters also affected the production of hydroxyl radicals. Increasing the amount of hydroxyl radical was obtained at the anode deeper position and the lower air flow rate which was less than 2 L/minute. At a high volume flow rate, the decrease in energy consumption that occured impacted on the production of hydroxyl radicals in which the higher rate of air injection, hydroxyl radicals generated were lower. The degradation process of Remazol Red as a textile dye was also influenced by the flow rate of injected air. In condition of optimum air flow volume of 0.05 L/minute, textile dye degradation was 96.04%, increased by 39.76% compared to the degradation process without air injection.
"
Depok: Fakultas Teknik Universitas Indonesia, 2019
D2688
UI - Disertasi Membership  Universitas Indonesia Library
cover
Fourina Sri Rahimah
"Elektrolisis plasma merupakan salah satu metode AOP (Advanced Oxidation Process) yang dapat menghasilkan radikal hidroksil (OH•) dan radikal hidrogen (H•) dalam jumlah lebih banyak. Penelitian ini bertujuan untuk mengetahui efektivitas elektroda stainless steel pada zona plasma anodik serta pengaruh laju injeksi udara dan daya terhadap degradasi Remazol Red dan erosi anoda. Penelitian dilakukan dengan reaktor 1,2 L menggunakan variasi laju injeksi udara 0,6 lpm, 0,8 lpm, 1 lpm, 1,2 lpm, dan 1,5 lpm serta variasi daya 400 W, 500 W, dan 600 W dengan elektrolit K2SO4 0,02 M.  Pada penelitian ini, didapat hasil degradasi yang lebih baik oleh elektroda stainless steel dibandingkan tungsten. Dalam waktu 8 menit, stainless steel mampu mendegradasi sebanyak 94,73% sedangkan tungsten hanya mampu sebesar 84,54% dan ditinjau dari erosinya stainless steel hanya tergerus sebanyak 0,07 gr, sedangkan tungsten sebanyak 1,8 gr. Laju injeksi udara yang menghasilkan tingkat degradasi optimum adalah 1,2 Lpm dan variasi daya yang optimum untuk laju injeksi tersebut adalah 500 W. Persentase degradasi optimum Remazol Red mencapai 99,84%, sementara degradasi Pt-Co sebesar 99,16%, dan COD sebesar 84,16% pada konsentrasi awal limbah 200 ppm dan FeSO4 20 ppm. Produk samping yang didapat berupa amonia sebesar 0,438 mmol dan nitrat sebesar 1,736 mmol.

Plasma electrolysis is an AOP (Advanced Oxidation Process) method that can produce more hydroxyl radicals (OH•) and hydrogen radicals (H•). This study aims to determine the effectiveness of stainless steel electrodes in the anodic plasma zone and the effect of air and power injection rates on the degradation of Remazol Red and anode erosion. The research was conducted with a 1.2 L reactor using air injection rate variations of 0.6 lpm, 0.8 lpm, 1 lpm, 1.2 lpm and 1.5 lpm and power variations of 400 W, 500 W and 600 W with electrolyte K2SO4 0.02 M. In this study, better degradation results were obtained by stainless steel electrodes than tungsten. Within 8 minutes, stainless steel was able to degrade as much as 94.73%, while tungsten was only able to 84.54% and in terms of its erosion, stainless steel only eroded as much as 0.07 gr, while tungsten as much as 1.8 gr. The air injection rate that produces the optimum degradation rate is 1.2 Lpm and the optimum power variation for the injection rate is 500 W. The optimum degradation percentage of Remazol Red reaches 99.84%, while the degradation of Pt-Co is 99.16%, and COD of 84.16% at the initial waste concentration of 200 ppm and 20 ppm FeSO4. The by-products obtained were 0.438 mmol of ammonia and 1.736 mmol of nitrate."
Jakarta: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Jessica Zivani Wahono
"Contact Glow Discharge Electrolysis (CGDE) atau teknologi elektrolisis plasma merupakan metode yang telah terbukti dalam mendegradasi limbah fenol secara efektif karena dapat memproduksi OH, H, dan spesi aktif lainnya dalam jumlah banyak. Penelitian ini bertujuan untuk memperoleh degradasi fenol secara efisien dengan penambahan injeksi udara secara langsung menuju anoda disertai dengan penambahan ion Fe. Karakterisasi arus-tegangan dalam reaktor CGDE diselidiki untuk memperkirakan kemungkinan daya listrik yang dapat digunakan untuk mendegradasi limbah fenol. Kondisi optimum yang didapat ditandai dengan besarnya produksi H O, persentase degradasi, dan energi.
Hasil percobaan menunjukkan bahwa setiap daya (500, 600, 700 watt) memiliki nilai optimal terhadap persentase degradasi. Kondisi optimal didapatkan pada daya 700 watt dengan laju injeksi udara 0,2 L min dan penambahan 20 mg L ion Fe. Setelah 30 menit pertama, persentase degradasi fenol yang diperoleh sebesar 79,25. Dengan kondisi yang sama, persentase degradasi fenol melonjak hingga 99,57 dengan penambahan 20 mg L ion Fe. Degradasi maksimum yang didapatkan adalah sebesar 99,89 setelah 90 menit. Nilai COD limbah fenol menurun dari 232,19 mg L menjadi 67 mg L setelah proses CGDE.

Contact glow discharge electrolysis (CGDE) or plasma electrolysis technology is a proven effective method of degrading such kind of waste because it can produce OH, H, and other active species in large quantities responsible for breaking down phenol structure. This study aims to obtain high efficiency phenol degradation using injection of air directly through anode and the presence of Fe ions. This research work presents the effect of the voltage to direct current connections in the CGDE reactor was investigated in order to estimate the possibilities for optimum electrical power on phenol degradation. In this research, production of hydrogen peroxide, percentage of phenol degradation, and energy consumption were used as main research indicators.
Experimental results show that each electrical power (500, 600, 700 watt) has an optimal value for the percentage of degradation. The optimal condition was found at 700 watt with the rate of air injection 0.2 L min and the addition of 20 mg L of Fe ions. After the first 30 minutes, the phenol degradation was valued at 79.25. Under the same conditions, with an addition of 20 mg L of Fe ions, the phenol degradation shot up to 99.57. Experimental results show that the largest phenol degradation was obtained at 99.89 after 90 minutes during the experiment. The COD value decreased from 232.19 mg L until 67 mg L after CDGE process.
"
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>