Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 20075 dokumen yang sesuai dengan query
cover
Nurfi Ahmadi
"Carbon black (CB) yang berasal dari limbah pertanian, batang bambu, tempurung kelapa dan tandan buah sawit diperoleh dengan proses pirolisis dapat digunakan sebagai penguat dalam komposit epoksi. Tujuan dari penelitian ini adalah mengetahui kekuatan tarik dan impak komposit berpenguat carbon black - epoksi. Bahan penguat yang digunakan dalam pembuatan komposit adalah carbon black yang bersumber dari biomassa limbah pertanian. Matrik yang digunakan adalah resin epoksi Baklite EPR 174 dan Epoxy Hardener V-140. Metode pembuatan komposit dengan metode hand lay up. Variasi pengujian dengan menggunakan Fraksi volum carbon black 0, 5, 10, 15, 20 %. Selanjutnya akan dilakukan uji tarik, uji impak dan SEM. Kekuatan tarik tertinggi sebesar 44,65 MPa pada 5% fraksi volume. Kekuatan impak tertinggi sebesar 5,47 MPa pada 5% fraksi volume. Hasil uji SEM menunjukan distribusi carbon black yang tidak merata pada epoksi, adanya aglomerasi, adanya void dan pull out."
Yogyakarta: Pusat Penelitian dan Pengabdian Pada Masyarakat (P3M) STTA, 2020
620 JIA XII:2 (2020)
Artikel Jurnal  Universitas Indonesia Library
cover
Felly Rihlat Gibran
"Rice husk is one of the most abundant agricultural wastes in Indonesia, with an annual potency of 13,662 MWe. Using biomass gasification, it can be converted into producer gas, whose energy can be used for thermal and electrical power generation. In gasification terms, gas quality can be interpreted by tar content and gas energy. An experiment using an open top fixed bed downdraft gasifier (batch system) with double stage air supply was conducted by varying the secondary air injection position (Z) and the air ratio (AR). Tar content can be represented by flaming pyrolysis duration and gas quality by the combustion energy of the gas. Flaming pyrolysis is a phenomenon which occurs inside the reactor, where tar produced is re-cracked and dissolved into smaller compounds. This can be achieved if the pyrolysis zone temperature ranges between 500 and 800oC. With an AR of 80%, at Z = 38 cm, flaming pyrolysis with the longest duration of 400 seconds was created, which indicated that this condition had the lowest tar content; meanwhile, at Z = 50 cm, gas with the highest energy (734.64 kJ) was obtained."
Depok: Faculty of Engineering, Universitas Indonesia, 2018
UI-IJTECH 9:2 (2018)
Artikel Jurnal  Universitas Indonesia Library
cover
Wica Delatoya
"ABSTRACT
Fenomena kerusakan lingkungan sangat erat kaitannya dengan aktivitas pembangunan. Oleh sebab itu diperlukan upaya dalam aktivitas pembangunan yang dapat meminimalisir dampaknya terhadap lingkungan. Pembangunan berkelanjutan yang berwawasan lingkungan atau disebut sustainable development merupakan pola dalam aktivitas pembangunan yang dapat meminimalisir pengaruh terhadap lingkungan. Salah satu bagian dari sustainable development yang berkaitan dengan fenomena dampak dari aktivitas pembangunan adalah sustainable construction, salah satu aspeknya adalah dengan konservasi terhadap penggunaan sumber daya alam. Konsep sustainable material adalah bagian dari sustainable construction yang berkaitan dengan konservasi sumber daya alam. Diperlukan tindakan untuk mendukung konsep sustainable material atau material berkelanjutan yaitu dengan menggunakan material dan teknologi yang sesuai. Salah satu upaya dari konsep material berkelanjutan yang dilakukan dalam skripsi ini adalah dengan menggunakan teknologi biokomposit, yaitu kombinasi antara serat alam dengan matriks. Dalam skripsi ini, limbah pertanian merupakan serat alam dan miselium merupakan matriks yang berperan sebagai perekat.

ABSTRACT
The phenomenon of environmental damage is very closely related to development activities. Therefore efforts are needed in development activities that can minimize their impact on the environment. Environmentally sustainable development or called sustainable development is a pattern in development activities that can minimize the influence on the environment. One part of sustainable development related to the phenomenon of the impact of development activities is sustainable construction, one of the aspects of which is conservation of natural resources. The concept of sustainable material is a part of sustainable construction that is related to the conservation of natural resources. Action is needed to support the concept of sustainable material by using appropriate materials and technology. One of the efforts of the sustainable material concept carried out in this paper is to use bio-composite technology, which is a combination of natural fibers with a matrix. In this paper, agricultural waste is a natural fiber and mycelium is a matrix that acts as an adhesive."
2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Lintang Ayu Kencana
"Sel tunam merupakan salah satu energi alternatif yang potensial untuk dikembangkan mengingat potensi dan jenis sumber energi yang terbarukan. Salah satu jenis sel tunam adalah Polymer Electrolyte Membrane Fuel Cell (PEMFC). Pada PEMFC terdapat komponen penting yang disebut dengan pelat bipolar. Pelat bipolar memiliki prosentase terbesar dalam berat dan biaya pembuatan sel tunam. Pada penelitian ini dibuat pelat bipolar karbon komposit dengan 80%wt matriks dan penguat yang terdiri dari 90-100% wt grafit dapur busur listrik (EAF) dan 0-10% wt carbon black FEF 550 dan 20%wt polimer sebagai pengikat yang terdiri dari epoksi resin dan pengeras dengan perbandingan 1:1. Pembuatan pelat bipolar ini dengan variabel penambahan 0-10%wt carbon black FEF 550 yaitu 0;2,5;5;7,5 dan 10%wt carbon black FEF. Proses pencampuran menggunakan pengaduk berkecepatan tinggi dengan kecepatan 28.000 rpm dan dicetak menggunakan metode cetak kompresi dengan tekanan 55 MPa, suhu 100°C, selama 4 jam. Hasil penelitian menunjukkan bahwa komposisi optimum terdapat pada 10%wt carbon black FEF 550 dimana dihasilkan nilai densitas sebesar 2,34 gr/cm3, porositas 2,39%, kekuatan fleksural 30,06 MPa, dan konduktivitas listrik 6,52 S/cm.

Fuel cell is one of the potentially alternative energy to be developed due to its potential and kind as renewable energy sources. Fuel cell has many types and one of them is PEMFC (Polymer Electrolyte Membrane Fuel Cell). Bipolar plate is one of main components in PEMFC which have the largest percentage in fuel cell weight and production cost. In this study, the bipolar plate materials made from carbon composites. Constituent materials carbon composites are 80wt% matrix and reinforcement, consist of 95wt% Graphite EAF (Electric Arc Furnace) and 0-10%wt carbon black FEF 550 and 20% polymer as binder consist of epoxy resin and hardener with ratio 1:1. The addition variabels 0-10%wt of carbon black FEF 550 are 0;2,5;5;7,5 and 10%wt. The mixing process used high-speed mixer with mixing speeds 28.000 rpm and to form the plate used compression molding with pressure 55 MPa, 100°C, for 4 hours. The test results showed that the maximum composition was 10%wt carbon black FEF 550 which values are density 2,34 gr/cm3, porosity 2,39%, flexural strength 30,06 MPa and electric conductivity 5,52 S/cm."
Depok: Fakultas Teknik Universitas Indonesia, 2013
S53503
UI - Skripsi Membership  Universitas Indonesia Library
cover
M. Ekaditya Albar
"Pelat bipolar merupakan komponen penting di dalam Polymer Electrolyte Membrane Fuel Cell (PEMFC) yang berfungsi untuk mengumpulkan dan memindahkan elektron dari anoda ke katoda. Pelat bipolar berbasis komposit terdiri dari grafit sintetis (MERCK) dan carbon black sebagai filler serta resin epoksi dan hardener sebagai binder. Carbon black dibuat dari pembakaran serabut kelapa pada suhu 500°C dan 900°C dalam kondisi inert. Pembahasan utama pada penelitian ini adalah menganalisis pengaruh variasi komposisi ukuran partikel carbon black sebagai variabel pertama dan lama pencampuran grafit dan carbon black dalam media air sebagai variabel kedua, terhadap distribusi sifatsifat pelat bipolar PEMFC berbasis komposit epoksi/grafit. Komposisi ukuran partikel carbon black hasil milling dengan rotary ball mill selama 2 hari berbanding 4 hari pada penelitian ini, yaitu 5:95, 10:90, 15:85 dan 20:80. Lama pencampuran antara grafit dan carbon black divariasikan dari 1 jam, 2 jam, 3 jam dan 4 jam dengan alat hand mixer di dalam media air. Pelat bipolar dicetak dengan metode compression molding dengan tekanan 55 MPa selama 4 jam pada suhu 100oC. Karakterisasi pelat bipolar meliputi pengujian konduktivitas listrik, pengujian fleksural, pengujian densitas, pengujian porositas, analisis gugus fungsional dengan FTIR dan pengamatan permukaan patahan fleksural menggunakan FE-SEM. Hasil penelitian menunjukkan bahwa komposisi optimal ukuran partikel carbon black hasil milling 2 hari dan 4 hari dengan perbandingan 15:85 pada lama pencampuran 3 jam dalam media air menghasilkan pelat bipolar dengan karakteristik nilai konduktivitas tertinggi sebesar 1.06 S/cm, kekuatan fleksural 48.38 MPa, densitas 2.50 gr/cm3 dan porositas 0.70%.

Bipolar plate is one of main components in Polymer Electrolyte Membrane Fuel Cell (PEMFC) that collects and transfers electron from anode to cathode. Bipolar plate composites consist of syntetic graphite (MERCK) and carbon black (CB) as filler material. Epoxy resin and hardener was used as binder material of the composite. Carbon black was prepared from combustion of palm fiber in 500 and 900°C through inert atmosphere. The main discussion in this research is to investigate the influence of variations in composition of carbon black particle size and mixing time of graphite and carbon black to the distribution of properties of PEMFC bipolar plates based on graphite/epoxy composite. Particle size composition ratio of milled carbon black in 2 days and 4 days are 5:95, 10:90, 15:85 and 20:80. Variation in mixing time of graphite and carbon black are 1 hour, 2 hours, 3 hours and 4 hours with water as mixing media. Characterization of bipolar plate material includes electrical conductivity test. flexural test, density and porosity measurement, functional groups analysis using FTIR and fracture surface examination using FE-SEM. The optimum composition was obtained in ratio of 2 days milled-CB : 4 days milled-CB in range of 15:85 and 3 hours mixing time using water. The optimum electrical conductivity, flexural strength, density and porosity were respectively: 1.06 S/cm, 48.38 MPa, 2.50 gr/cm3 and 0.70%."
Depok: Fakultas Teknik Universitas Indonesia, 2013
T33734
UI - Tesis Membership  Universitas Indonesia Library
cover
Arfiana
"Poliester tak jenuh memiliki aplikasi luas namun mudah terbakar. Aditif halogen awalnya digunakan untuk meningkatkan fire retardancy komposit namun memiliki efek samping negatif terhadap kesehatan. Pada penelitian ini dilakukan sintesis fire retardant composite dengan variasi konsentrasi aditif Al(OH)3/Mg(OH)2 dan filler carbon black. Parameter fire retardancy yang diamati adalah time to ignition (ti), time taken to retard the fire (tr), burning time (tb), dan flammability rating menurut standar UL-94V. Komposisi aditif terbaik diperoleh pada konsentrasi Al(OH)3 40%/Mg(OH)2 10% dengan ti 22,5 detik, tr 6,2 detik, tb 7,8 detik, dan flammability rating V?0. Penambahan filler carbon black sebanyak 2,5% meningkatkan fire retardancy komposit dengan nilai ti 30 detik, tr 1,4 detik, tb 3,5 detik, dan flammability rating V?0. Penambahan aditif dan filler CB mampu meningkatkan stabilitas termal komposit dengan menurunkan mass loss rate (MLR) dan total mass loss. Komposit resin/aditif terbaik (Al(OH)3 40%/Mg(OH)2 10%) memiliki nilai tensile strength sebesar 18,2 MPa dan hardness 51. Sedangkan komposit resin/aditif/filler terbaik (Al(OH)3 40%/Mg(OH)2 10%/CB 2,5%) memiliki nilai tensile strength sebesar 13,9 MPa dan hardness 55.

Unsaturated polyester resin has wide application but is flammable. Halogen additive was originally used for improving the fire retardancy of the composite but has the negative effects on health. In this research, synthesis of fire retardant composite has been conducted by varying additive Al(OH)3/Mg(OH)2 and carbon black filler concentration. Fire retardancy parameters need to be observed are time to ignition (ti), time taken to retard the fire (tr), burning time (tb), and flammability rating as per UL-94V standard. Additive composition shows the best result at the concentration of Al(OH)3 40%/Mg(OH)2 10% with ti value of 22.5 s, tr 6.2 s, tb 7.8 s, and V-0 flammability rating. Adding carbon black filler of 2.5% improves the fire retardancy of composite with ti value of 30 s, tr 1.4 s, tb 3.5 s, and V-0 flammability rating. Adding of additive and CB filler can improve the thermal stability of composite by reducing mass loss rate (MLR) and total mass loss. The best resin/additive composite (Al(OH)3 40%/Mg(OH)2 10%) has tensile strength value of 18.2 MPa and hardness 51. Whereas, the best resin/additive/filler composite (Al(OH)3 40%/Mg(OH)2 10%/CB 2.5%) has tensile strength value of 13.9 MPa and hardness 55.
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
T45150
UI - Tesis Membership  Universitas Indonesia Library
cover
Elisabeth Srihayu Harsanti
"ABSTRAK
Endosulfan adalah salah satu senyawa POPs organoklorin pada era revolusi hijau yang disukai petani karena kemanjurannya. Namun saat ini masih ditemukan di lapang. Endosulfan bersifat persisten, bioakumulatif, dan sangat toksik terhadap makrobiota. Keberadaan endosulfan harus dipantau dan dilakukan upaya reduksinya agar tidak mencemari lingkungan, dan untuk keamanan pangan, serta memenuhi ketentuan Konvensi Stockholm. Sekitar 18,12 dari total tanah sawah di Kabupaten Jombang telah terkontaminasi endosulfan dengan kategori telah melebihi Batas Maksimum Residu BMR dan 22,5 di bawah BMR. Upaya remediasi harus dilakukan dengan memanfaatkan sumberdaya lokal di Kabupaten Jombang seperti limbah tongkol jagung dan pupuk kandang. Limbah tongkol jagung belum optimal dimanfaatkan. Biochar dari limbah tongkol jagung berpotensi untuk memperbaiki tanah sawah terkontaminasi endosulfan. Penelitian ini bertujuan 1 mengetahui kemampuan teknologi remediasi dengan limbah pertanian berbasis sumberdaya lokal dalam memperbaiki kualitas tanah sawah dan produk pertanian tercemar insektisida endosulfan, 2 mengkaji dampak teknologi remediasi dengan limbah pertanian berbasis sumberdaya lokal pada tanah sawah tercemar endosulfan dengan menggunakan perangkat valuasi ekonomi, sosial, dan lingkungan dan 3 membangun model statistik remediasi berkelanjutan dengan limbah pertanian berbasis sumberdaya lokal pada tanah sawah tercemar endosulfan. Penelitian dilakukan pada bulan Juni 2015-Mei 2016 dengan metode survey dan eksperimen di rumah kaca. Eksperimen di rumah kaca menggunakan rancangan percobaan acak lengkap dengan tujuh perlakuan kombinasi biochar dan kompos kotoran ternak yang diulang tiga kali. Hasil penelitian menunjukkan 1 Teknologi remediasi tanah sawah tercemar insektisida endosulfan dengan limbah pertanian dapat memperbaiki kualitas tanah dan produk pertanian padi . Kombinasi biochar tongkol jagung dan kompos kotoran sapi atau ayam 1:4 efektif sebagai bahan pembenah tanah untuk remediasi tanah sawah tercemar residu insektisida endosulfan dengan kemampuan mempercepat penurunan ?-endosulfan hingga lebih rendah dari konsentrasi BMR < 0,0085 ppm berkisar 66,5 - 70,9 dengan waktu remediasi selama 74 hari 21 hari lebih cepat daripada tanpa remediasi ; Kombinasi biochar tongkol jagung dengan pupuk kandang sapi atau ayam pada nisbah 1:4 dapat menurunkan residu metabolit endosulfan sulfat hingga di bawah BMR < 0,0085 ppm masing-masing sebesar 1,8 -67,3 pada MT I, dan 49,7 -67,7 pada MT II dan terjadi pada kondisi anaerob; Kombinasi biochar dan kompos kotoran ternak mampu meningkatkan kesuburan tanah antara lain pH, P tersedia, C organik tanah, N total, dan populasi bakteri dalam tanah; serta meningkatkan hasil padi 10-13 2 Teknologi remediasi dengan memanfaatkan biochar tongkol jagung yang dikombinasi dengan kompos kotoran ayam atau sapi dapat memberikan dampak positif pada aspek ekonomi, sosial, dan lingkungan sehingga inovasi tersebut dapat diterima oleh petani; dan 3 Model statistik remediasi tanah sawah Inceptisol tercemar residu endosulfan dengan memanfaatkan limbah pertanian dapat dibangun dengan mempertimbangkan karakteristik tanah terutama kandungan C-organik tanah dan populasi bakteri total dalam tanah.Kata kunci: limbah tongkol jagung, kompos kotoran sapi, kompos kotoran ayam biochar, remediasi, endosulfan, keberlanjutan

ABSTRACT
Endosulfan is one of POPs organochlorine compounds on green revolution era that was mostly preferred by farmers because of its efficacy. However, it still found in the field. Endosulfan is persistent, bio accumulative, and most toxic on macrobiota. Its existence in soil must be monitored and its reduction must be controlled so that it do not contaminate the environment and food safety and comply Stockholm Convention. About 18.12 of total rice fields in Jombang districts has contaminated by endosulfan that has been over Maximum Residue Limits MRLs and 22,5 less of MRLs. Remediation should be done by using local sources such as corn cob waste and compost of cattle manure. In fact, the waste of corn cob has not used optimally yet. Biochar from corn cob waste has the potency to remediate rice fields contaminated endosulfan. The research objectives were 1 to determine ability of remediation technology using agricultural wastes based local resources in improving quality of paddy soil and agricultural products that polluted by endosulfan insecticide, 2 to study the impacts of remediation technology using agricultural wastes based local resources in rice fields contaminated by endosulfan through economic, social, and environment valuation instruments, and 3 to arrange statistical model of sustainable remediation using agricultural waste based local resources in rice field contaminated by endosulfan. The research was conducted from June 2015 till May 2016 using survey and screen house experiment methods. The screen house experiment was arranged using completely randomized design with seven treatment of combination of corn cob biochar and farmyard manure with three replicates. The research result showed that 1 remediation technology of rice fields contaminated by endosulfan using agricultural waste as a soil amendment could improve the quality of paddy soil and rice products. The combination of corn cob biochar and compost of cattle manure or chicken manure 1 4 could effectively remediate rice field contaminated by endosulfan insecticide till less than MRLs 0.0085 ppm as much as 66.5 ndash 70.9 . The time of remediation to reduce the residue up to less than MRLs was 74 days 21 days faster than without remediation . The combination of corn cob biochar and cattle manure or chicken manure with 1 4 ratio could decrease endosulfan sulfate metabolite less MRLs 0,0085 ppm 1.8 67.3 in 1st cropping season and 49.7 67.7 2nd cropping season , respectively, that a decrease is in anaerobe condition Soil amendment could increase soil fertility, i.e. pH, available P, soil organic C, total N, and bacteria population and increased 10 13 of rice yield 2 remediation technology using corn cob biochar combined manure from either cattle or chicken could impact positively on aspects of economy, social, and environment so that innovation could be acceptable by farmers and 3 statistical model of remediation of Inceptisol rice field that contaminated by endosulfan using agricultural waste could be built with considering soil characteristic especially organic C and soil bacteria total factors. Its usage was suitable with level of endosulfan contamination and has some similarities ecological characteristics.Keywords corn cob waste, cattle manure compost, chicken manure compost, biochar, remediation, endosulfan, sustainability. "
2016
D-Pdf
UI - Disertasi Membership  Universitas Indonesia Library
cover
Maya Ayu Wulandari
"Pelat bipolar merupakan komponen utama dalam Polymer Electrolyte Membrane Fuel Cell (PEMFC). Pada penelitian ini pelat bipolar dibuat dari grafit komposit yang terdiri dari matriks grafit Electric Arc Furnace (EAF), carbon black sebagai pengisi, dan resin epoksi sebagai pengikat. Semua bahan dicampur dengan menggunakan high speed mixer dengan variabel komposisi dari carbon black ISAF N220 0%, 2.5%, 5%, 7.5%, dan 10%.
Metode compression moulding dilakukan dalam pembuatan pelat bipolar dengan menggunakan tekanan 55 MPa selama 4 jam pada temperatur 100°C. Material dikarakterisasi melalui pengujian tarik, pengujian fleksural, pengujian densitas, pengujian porositas, pengujian konduktivitas listrik, dan pengujian Field Electron Scanning Electron Microscope (FESEM).
Hasil penelitian menunjukkan bahwa pada komposisi carbon black 10% menghasilkan pelat bipolar dengan karakteristik optimum dengan nilai konduktivitas tertinggi sebesar 7,07 S/cm. Kekuatan fleksural sebesar 51,34 MPa. Namun demikian, densitas terendah sebesar 1,96 gr/cm3 diperoleh dengan melakukan pencampuran carbon black 0% , dan porositas terkecil 0,49% diperoleh pada komposisi carbon black 10%. Pengamatan visual menunjukkan bahwa seluruh pelat bipolar mempunyai penampakan yang baik, tidak retak, dan permukaan yang rata.

Bipolar plate is a major component in Polymer Electrolyte Membrane Fuel Cell (PEMFC). In this study bipolar plates made of graphite composite consisting of a matrix of graphite Electric Arc Furnace (EAF), carbon black as filler, and epoxy resin as a binder. All the ingredients are mixed using a high speed mixer with variable composition of carbon black ISAF N220 0%, 2.5%, 5%, 7.5%, and 10%.
Methode of compression molding is done in the manufacture of bipolar plates using a pressure of 55 MPa for 4 hours at a temperature of 100°C.
The results showed that the composition of 10% carbon black produce bipolar plates with optimum characteristics with the highest conductivity value of 7.07 S / cm. Fleksural strength of 51.34 MPa. However, the lowest density of 1.96 gr/cm3 obtained by mixing carbon black 0%, and the smallest porosity of 0,49% is obtained on the composition of 10% carbon black. Visual observations showed that all bipolar plates have a good appearance, no cracks, and a flat surface.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
S46392
UI - Skripsi Membership  Universitas Indonesia Library
cover
Arfiana
"Poliester tak jenuh memiliki aplikasi luas namun mudah terbakar. Aditif halogen awalnya digunakan untuk meningkatkan fire retardancy komposit namun memiliki efek samping negatif terhadap kesehatan. Pada penelitian ini dilakukan sintesis fire retardant composite dengan variasi konsentrasi aditif Al(OH)3/Mg(OH)2 dan filler carbon black. Parameter fire retardancy yang diamati adalah time to ignition (ti), time taken to retard the fire (tr), burning time (tb), dan flammability rating menurut standar UL-94V. Komposisi aditif terbaik diperoleh pada konsentrasi Al(OH)3 40%/Mg(OH)2 10% dengan ti 22,5 detik, tr 6,2 detik, tb 7,8 detik, dan flammability rating V–0. Penambahan filler carbon black sebanyak 2,5% meningkatkan fire retardancy komposit dengan nilai ti 30 detik, tr 1,4 detik, tb 3,5 detik, dan flammability rating V–0. Penambahan aditif dan filler CB mampu meningkatkan stabilitas termal komposit dengan menurunkan mass loss rate (MLR) dan total mass loss. Komposit resin/aditif terbaik (Al(OH)3 40%/Mg(OH)2 10%) memiliki nilai tensile strength sebesar 18,2 MPa dan hardness 51. Sedangkan komposit resin/aditif/filler terbaik (Al(OH)3 40%/Mg(OH)2 10%/CB 2,5%) memiliki nilai tensile strength sebesar 13,9 MPa dan hardness 55.

Unsaturated polyester resin has wide application but is flammable. Halogen additive was originally used for improving the fire retardancy of the composite but has the negative effects on health. In this research, synthesis of fire retardant composite has been conducted by varying additive Al(OH)3/Mg(OH)2 and carbon black filler concentration. Fire retardancy parameters need to be observed are time to ignition (ti), time taken to retard the fire (tr), burning time (tb), and flammability rating as per UL-94V standard. Additive composition shows the best result at the concentration of Al(OH)3 40%/Mg(OH)2 10% with ti value of 22.5 s, tr 6.2 s, tb 7.8 s, and V-0 flammability rating. Adding carbon black filler of 2.5% improves the fire retardancy of composite with ti value of 30 s, tr 1.4 s, tb 3.5 s, and V-0 flammability rating. Adding of additive and CB filler can improve the thermal stability of composite by reducing mass loss rate (MLR) and total mass loss. The best resin/additive composite (Al(OH)3 40%/Mg(OH)2 10%) has tensile strength value of 18.2 MPa and hardness 51. Whereas, the best resin/additive/filler composite (Al(OH)3 40%/Mg(OH)2 10%/CB 2.5%) has tensile strength value of 13.9 MPa and hardness 55."
Depok: Fakultas Teknik Universitas Indonesia, 2016
T45150
UI - Tesis Membership  Universitas Indonesia Library
cover
"Cultured sporophytic thalli of Undaria pinnatifida were collected at different periods of the year from Okkirai Bay, northeastern Japan
.."
Artikel Jurnal  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>