Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 98928 dokumen yang sesuai dengan query
cover
Agung Gita Manohara
"Penggunaan cangkang kelapa sawit (OPS) sebagai pengganti agregat kasar alami dalam campuran beton akan membantu mengurangi jumlah limbah yang dihasilkan dari sisa produksi industri minyak kelapa sawit. Objek studi pada penelitian ini adalah beton dengan substitusi 100% cangkang kelapa sawit (OPS) sebagai pengganti agregat kasar dengan penggunaan semen OPC. Penggunaan semen OPC dipilih untuk melihat perbedaan karakteristik beton OPS jika digunakan semen portland murni dengan mengacu pada proporsi campuran beton yang sudah pernah dilakukan pada penelitian sebelumnya. Pengujian karakteristik beton yang dilakukan pada penelitian ini meliputi pengujian kuat tekan, kuat tarik lentur, kuat tarik belah, susut beton, dan permeabilitas. Pada penelitian ini juga akan dilakukan pengujian untuk mengetahui respon struktur balok beton bertulang dengan menggunakan sampel balok berukuran 15x25x300 cm³. Pengujian sampel balok OPS dilakukan dengan metode four-point loading dengan alat pencetak respons 3D berupa Digital Image Correlation (DIC) untuk menganalisa respon struktur, distribusi pola retak, dan bukaan yang terjadi pada balok beton OPS. Metode pembebanan pada penelitian ini dilakukan secara bertahap (semi-siklik) dalam 4 siklus, yaitu siklus 2 ton, 4 ton, 6 ton, dan 8 ton. Hasil pengujian menunjukan kuat tekan maksimum beton OPS dengan semen OPC mencapai 19.84 MPa. Selain itu, berdasarkan hasil pengujian permeabilitas, beton OPS dengan semen OPC tidak tahan terhadap penetrasi air. Kuat tarik beton OPS dengan semen OPC berkisar 5- 8% dari kuat tekannya. Balok beton OPS dengan campuran semen OPC dapat menahan beban hingga 7300 kg dan menghasilkan lendutan sebesar 26.7 mm. Pola retak pada balok terdistribusi merata di sepanjang bentang dan dapat diamati dengan metode Digital Image Correlation (DIC). Hasil dari penelitian ini, beton campuran cangkang kelapa sawit dengan semen OPC dapat dijadikan sebagai beton struktural sederhana karena mampu menahan beban yang cukup besar dan menghasilkan kuat tekan yang tinggi serta lendutan yang tidak terlalu besar.

The use of palm kernel shell (OPS) as a substitute for natural coarse aggregates in concrete mixtures will help reduce the amount of waste generated from palm oil industry. The object of study in this research is concrete with 100% substitution of palm kernel shell (OPS) as a replacement for coarse aggregate using Ordinary Portland Cement (OPC). The used of Ordinary Portland Cement (OPC) was chosen to observe the differences in OPS concrete characteristics when pure Portland Cement is used, referring to the concrete mix proportions previously research. The concrete characteristics tested in this research include compressive strength, flexural tensile strength, split tensile strength, shrinkage, and permeability. This research also conducted tests to determine the structural response used a sample of reinforced concrete beams 15x25x300 cm³. The testing of OPS beam samples is perfomed using four-point loading method with 3D response printing tool called Digital Image Correlation (DIC) to analyze the structural response, crack pattern distribution, and crack opening in the OPS concrete beams. The loading method in this research is semi-cyclic in 4 cycles, namely 2 tons, 4 tons, 6 tons, and 8 tons. The test results show that the maximum compressive strength of OPS concrete with OPC reaches 19.84 MPa. Furthemore, based on the permeability test result, OPS concrete with OPC not resistant to water penetration. The tensile strength of OPS concrete with OPC reaches 5-8% of its compressive strength. OPS concrete beams with the OPC can withstand loads of up to 7300 kg and produce a deflection of 26.7 mm. The crack pattern is evely distributed along the span of beams and can be observed using the Digital Image Correlation (DIC) method. The results of this research indicate that the mixture of palm kernel shells and Ordinary Portland Cement (OPC) can be used as a simple structural concrete because it can withstand significant loads and has high compressive strength, as well as moderate deflection."
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Dini Rahmadhanti
"Cangkang kelapa sawit merupakan limbah hasil sektor pertanian yang memiliki potensi produksi yang tinggi namun belum dimanfaatkan secara maksimal di Indonesia. Penggunaan cangkang kelapa sawit sebagai pengganti agregat kasar pada beton telah banyak dilakukan. Dengan berat isi yang cukup ringan, cangkang kelapa sawit dapat menghasilkan beton ringan dengan berat jenis ±1900 kg/m3. Portland Composite Cemen (PCC) merupakan semen umum yang digunakan dipasaran. Semen ini memiliki butiran yang lebih halus sehingga menghasilkan panas hidrasi yang lebih rendah. Pada penelitian ini akan dilakukan studi eksperimen pada balok yang menggunakan cangkang kelapa sawit dari berbagai campuran jenis dan semen PCC sebagai pengikatnya. Pengujian yang dilakukan adalah uji kerakteristik beton (uji kuat tekan, kuat tarik belah, kuat lentur, permeabilitas, dan susut) serta pengujian pembebanan terhadap balok berukuran 300 x 15 x 25 cm3 menggunakan four-point loading serta pengamatan dengan metode Digital Image Correlation (DIC). Analisis yang dilakukan meliputi respon struktur balok akibat pembebanan, pola retak yang dihasilkan, serta bukaan retak yang terjadi selama proses pembebanan dilakukan. Hasil eksperimen menunjukkan karakteristik beton yang kurang memuaskan dimana hanya diperoleh kuat tekan sebesar 12,41 MPa. Balok beton bertulang cangkang kelapa sawit pada penelitian ini mampu menerima beban hingga 7000 kg. Pola retak yang terbentuk sudah sesuai dengan pembebanan yang dilakukan dan evolusi dari pembukaan retak yang diamati dapat terlihat dengan baik menggunakan metode DIC. Bukaan retak yang dihasilkan berkisar antara 100-300 μm. Meskipun menghasilkan respon struktur yang cukup baik, balok beton bertulang cangkang kelapa sawit tidak dapat dijadikan sebagai komponen struktural karena kecilnya kuat tekan yang dihasilkan. Perlu dilakukan penelitian lebih lanjut terkait dengan penggunaan cangkang kelapa sawit sebagai pengganti agregat kasar dalam campuran beton untuk komponen non-struktural.

Oil palm shells are agricultural waste with high production potential that has not been fully utilized in Indonesia. The use of oil palm shells as a replacement for coarse aggregates in concrete has been widely explored. With its relatively low density, oil palm shells can produce lightweight concrete with a density of approximately 1900 kg/m3. Portland Composite Cement (PCC) is a commonly used cement in the market. It has finer particles, resulting in lower hydration heat. This study aims to conduct experimental studies on beams using oil palm shells in various mixtures and PCC as the binder. The testing includes characterization of the concrete (compressive strength, splitting tensile strength, flexural strength, permeability, and shrinkage), as well as load testing on 300 x 15 x 25 cm3 beams using four-point loading and observation using Digital Image Correlation (DIC) method. The analysis includes studying the structural response of the beams under loading, crack patterns, and crack opening during the loading process. The experimental results indicate unsatisfactory characteristics of the concrete, as only a compressive strength of 12.41 MPa was obtained. The reinforced concrete beams with oil palm shells in this study can sustain loads up to 7000 kg. The crack patterns formed are consistent with the applied loading, and the evolution of crack opening can be well observed using the DIC method. The crack openings range from 100 to 300 μm. Although the beams exhibit satisfactory structural response, they cannot be used as structural components due to their low compressive strength. Further research is needed regarding the use of palm kernel shells as a substitute for coarse aggregate in concrete mixtures for non-structural components."
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Cellen Syafira Putri
"Cangkang kelapa sawit (OPS) dapat digunakan secara optimal sebagai alternatif agregat kasar dengan tujuan untuk mengurangi limbah OPS dan menghemat biaya produksi. Beton dengan campuran OPS sebagai agregat kasar dengan semen portland komposit (PCC) telah banyak dilakukan pada penelitian terdahulu. Pada penelitian ini digunakan beton dengan cangkang kelapa sawit sebagai pengganti agregat dengan menggunakan semen portland pozzolan (PPC) untuk mengamati perbedaan karakteristik beton terhadap semen lainnya.  Penelitian ini menganalisis karakteristik beton seperti kuat tekan, kuat tarik belah, permeabilitas, susut, kuat lentur, serta analisis respon struktur balok beton bertulang. Analisis respon struktur menggunakan sampel balok beton bertulang 15×25×300 cm3 yang diberi beban semi-siklik dengan metode pembebanan four point loading. Respon struktur yang diamati berupa perpindahan, regangan, dan pola retak balok diolah dari hasil pengujian menggunakan Digital Image Correlation (DIC) dan pengukuran manual menggunakan LVDT. Hasil eksperimen menghasilkan kuat tekan beton sebesar 8.73 MPa. Balok cangkang kelapa sawit (OPS) dengan semen portland pozzolan (PPC) dapat menerima beban hingga 6500 kg dan menghasikan lendutan hingga 30mm. Distribusi pola retak yang dihasilkan tersebar sepanjang balok dan dapat diamati menggunakan metode Digital Image Correlation (DIC). Hasil dari penelitian ini, beton campuran cangkang kelapa sawit (OPS) dengan semen portland pozzolan (PPC) tidak dapat digunakan sebagai komponen struktural karna menghasilkan kuat tekan beton yang rendah dan lendutan yang cukup besar. 

Oil palm shells (OPS) can be used optimally as an alternative for coarse aggregate in purpose to reduce OPS waste and save production costs. OPS concrete with porland cement composite (PCC)  has been widely used in previous studies. in this experiment, OPS used as a subtitue for coarse aggregate with Portland Pozzolan Cement (PPC) to observe the differences in the characteristis of concrete compared to other cements. This study analyzed the characterictis of concrete such as compressive strength, split tensile strength, permeability, shrinkage, flexural strength, as well as analysis of the structural response of reinforced concrete beams. Structural response analysis used a sample of reinforced concrete beams 15×25×300 cm3 which was given a semi-cyclic load using the four point load method. The observed structural responses in the form of displacement, strain, and beam crack patterns were processed from the test results using Digital Image Correlation (DIC) and measurements using LVDT. The compressive strength obtained from this experiment is 8.73 MPa. Reinforced beam with a mixture of of oil palm kernel shell (OPS) and portland pozzolan cement (PPC) were able to withstand loads up to 6500 kg and produce deflections of up to 30mm. The resulting crack pattern distribution is spread along the beam and can be observed using the Digital Image Correlation (DIC) method. The results of this study, concrete mixed with oil palm shells (OPS) with portland pozzolan cement (PPC) cannot be used as a structural component due to it low concrete compressive strength and a significant deflection."
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
I Putu Andika Candra Wibawa
"Beton bertulang merupakan material yang sering digunakan dalam melakukan pembangunan infrastruktur. Penggunaan beton bertulang ini harus diikuti dengan kualitasnya yang baik. Penentuan kualitas dari suatu beton dapat dilakukan dengan cara melakukan pengujian. Salah satu jenis dari pengujian beton ini adalah Non-Destructive Test (NDT), yang merupakan pengujian beton tanpa merusak struktur beton itu sendiri. Pada penelitian ini dilakukan pengujian NDT dengan menggunakan lima jenis alat yang dilakukan pada pelat beton berukuran 2x2 m dengan berbagai bentuk rangkaian tulangan pelat dan balok di dalamnya. Kelima jenis alat tersebut antara lain, Ground Penetrating Radar (GPR), Profometer, Elcometer, Ultrasonic Pulse Velocity (UPV), dan Ultrasonic Tomograph Portable. Alat GPR, profometer, dan elcometer dapat menentukan kedalaman dari tulangan. Pembacaan kedalaman tulangan ini dilakukan analisis perbandingannya untuk ketiga alat dengan melihat perbedaan hasil pemindaiannya. Dengan menggunakan konsep radar, alat GPR mampu mendeteksi suatu tulangan lapisan bawah, berbeda halnya dengan profometer dan elcometer yang menggunakan prinsip kerja arus eddy dan hanya dapat mendeteksi tulangan lapisan atas. Adapun alat UPV dan Ultrasonic Tomograph Portable yang dapat memancarkan gelombang dan menghasilkan cepat rambat gelombang yang berbeda. Hasil cepat rambat gelombang ini menunjukkan bahwa cepat rambat gelombang longitudinal dari alat UPV dengan metode indirect sangat dipengaruhi oleh jarak antar transduser, namun nilai cepat rambat gelombang geser yang dihasilkan oleh alat Ultrasonic Tomograph Portable mengalami kenaikan yang lebih konstan dibandingkan dengan cepat rambat gelombang longitudinal alat UPV saat umur beton bertambah.

Reinforced concrete is a material that is often used in infrastructure development. The use of reinforced concrete must be followed by good quality. Determination of the quality of a concrete can be done by testing. One type of concrete testing is the Non-Destructive Test (NDT), which is a test of concrete without damaging the concrete structure itself. In this study, NDT testing was carried out using five types of tools carried out on a 2x2 m concrete slab with various forms of plate and beam reinforcement in it. The five types of NDT tools are Ground Penetrating Radar (GPR), Profometer, Elcometer, Ultrasonic Pulse Velocity (UPV), and Ultrasonic Tomograph Portable. GPR, profometer, and elcometer can determine the depth of reinforcement. The reading of the reinforcement depth is carried out by comparative analysis for the three tools by looking at the differences in the scan results. By using the radar concept, GPR is able to detect an underlayer reinforcement, in contrast to the profometer and elcometer which use the working principle of eddy currents which can only detect the top layer reinforcement. The UPV and Ultrasonic Tomograph Portable tools can emit waves and produce different wave propagation speeds. The results of this wave propagation speed indicate that the longitudinal wave propagation speed of the UPV with the indirect method is strongly influenced by the distance between the transducers, but the value of the shear wave propagation speed generated by the Ultrasonic Tomograph Portable has a more constant increase compared to the longitudinal wave propagation speed of the UPV when the age of the concrete increases."
Depok: Fakultas Teknik Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Nawy, Edward G.
Surabaya: ITS Press, 2010
624.183 41 NAW b
Buku Teks  Universitas Indonesia Library
cover
Nawy, Edward G.
Bandung: Eresco, 1990
624.183 41 NAW b
Buku Teks  Universitas Indonesia Library
cover
McCormac, Jack C.
Jakarta : Erlangga, 2001
624.1 MCC d
Buku Teks SO  Universitas Indonesia Library
cover
Rico Bonar
"The beam-column joint in a reinforced concrete structure is an area with great attention, because of it's important function of transferring the forces from the beam to the column. As the transferring agent, reinforced concrete consisted of concrete and steel reinforcement that must work together to hold and transfer loads. We can examine the cooperation of these two elements from their bonding mechanism. The anchorage length of tensile steel is the determining factor to the quality of the bonding mechanism. The small dimension of column will contribute to the limited length of the anchorage, which is under the prescribed length of the governing rules. Therefore to increase the length of the anchorage, a hump is made on the outer side of the exterior joint. In this experimental study we will examine the bonding quality and the cracking pattern on the specimen's joint which is modelled from a 5 story office building which is scaled to 1 : 2 size. This experimental study will be held in a laboratory using a hydraulic jack to pull the steel reinforcement from the concrete structure, so that the strain and bonding mechanism can be examined. From experiment conducted, a number of conclusions can be drawn; The bonding quality, which is numerically gauged by the average bond stress, it's value rises linearly and reach their yielding point. While the failure pattern on the specimen is considered to be splitting mechanism which started from the loaded end of column to the outside of the joint.

Daerah pertemuan balok-kolom beton bertulang merupakan daerah yang perlu mendapat perhatian khusus, karena fungsinya yang penting sebagai tempat penyaluran gaya dari balok ke kolom. Sebagai sarana penyalur, beton bertulang yang terdiri atas beton dan baja hams dapat bekerjasama dengan baik dalam menahan dan menyalurkan beban, keriasama ini dapat kita lihat kinerianya dari mekanisme lekatan antara tulangan baja dengan beton. Panjang penjangkaran tulangan tank adalah faktor yang menentukan terhadap kualitas lekatan yang diperoleh. Dimensi kolom yang kecil menyebabkan panjang penyaluran menjadi terbatas sehingga tidak memenuhi syarat yang ditetapkan oleh peraturan. Oleh sebab itu untuk menambah panjang penjangkaran dibuat penonjolan pada sisi luar sambungan eksterior balok-kolom. Pada studi eksperimen ini akan dilihat kualitas lekatan dan pola keruntuhan yang terjadi pada spesimen berbentuk sambungan yang didapat dari pemodelan gedung perkantoran 5 lantai. yang berskalakan 1:2. Studi eksperimen yang dilakukan di laboratorium ini menggunakan hydraulic jack untuk menarik tulangan baja dari beton bertulang, sehingga didapat tegangan lekat serta regangan tulangan yang terjadi. Dari eksperimen yang telah dilakukan dapat ditarik kesimpulan sebagai berikut, kualitas lekatan yang besamya diukur secara numerik oleh satuan tegangan lekat rata-rata, trend nilainya bertambah secara linier dan mencapai konstan saat tulangan tersebut mengalami leleh, sedangkan pola keruntunan yang terjadi pada spesimen berjenis splitting yang dimulai dari ujung kolom yang dibebani menuju keluar joint."
Depok: Fakultas Teknik Universitas Indonesia, 2004
S35449
UI - Skripsi Membership  Universitas Indonesia Library
cover
Nawy, Edward G.
Englewood Clifs, NJ: Prentice-Hall, 1985
624.183 41 NAW r
Buku Teks  Universitas Indonesia Library
cover
Wight, James K.
Upper Saddle River, N.J : Prentice-Hall, 2009
624.183 412 WIG r
Buku Teks  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>