Hasil Pencarian  ::  Simpan CSV :: Kembali

"ABSTRACT

Probing of the atmospheric parameters have been done by many scientists since a century ago up to present with various techniques. A simple system of laser radar without using any collimated beam but a reflected mirror as transmitter and a small cassegranian type (10.5 an in diameter) telescope as receiving was constructed to investigate the relative Mie backscattering coefficient by utilizing a nitrogen laser as a light source in the range of measurement bellow 1 Km. The backscattered light received by the receiving telescope is converted into electric current by photomultiplier and is shown and known as "A scope" display on an oscilloscope. SNR of the signal from photomultiplier was increased by using a boxcar integrator and its output could be recorded with XY recorder."

"ABSTRACTLaser induced thin film production (LITFP) technique was employed for making plumbum (Pb) thin film by nitrogen laser deposition in miniature scale. The energy of nitrogen laser operated at 12.5 kv, 90 torr was 3.5 mj with 5 ns pulse duration, thus producing peak power at around 0.7 MW. Pb plasma of 1 cm diameter was generated in each laser bombardment, producing thin film above the glass substrate. The thin film characteristics were measured by means of their thickness and surface morphology using scanning electron microscope (SEM). It was proved that there was a linear relationship between the number of laser shots and film thickness."

"Kopling antara amplifier permukaan miring dan fiber taper lens-ended diselidiki secara teori. Penelitian teori didasarkan pada model gelombang bidang tiga dimensi yang dihitung melalui pergeseran fasa akibat permukaan iring. Kopling diselidiki berkenaan dengan parameter-parameter berkas dari pandu gelombang amplifier lens-ended, dan juga berkenaan dengan posisi fiber. Terjadinya rugi-rugi kopling karena permukaan miring dan karena variasi dari uji lens yang terbaik, rugi untuk permukaan miring 10° ditemukan lebih kecil dari 0.5 dB dibandingkan amplifier permukaan normal.

---

The coupling between angled-facet amplifiers and tapered lens-ended fibers is investigated theoretically. The theoretical investigation is based on a three-dimensional plane wave model which accounts for the phase differences introduced by the angled facets. The coupling is investigated with respect to the beam parameters of the amplifier wave guids and the tapered lens-ended fiber, and also with respect to the fiber position. For optimized lens radii the excess loss for 0l0° facet angle is found to be less than 0.5 dB compared to a normal facet amplifier."

"ABSTRACTThe frequency dobled Rd: YAG laser (532 nm/10ns, 15mj/pulse) uses a pulsed, frequency dobled; which provides a monochromatic, energy source with extremely high peak power and to has capability to develop of latent fingerprint on various surface. In the porous surfaces, this laser to has superiority, the compared with the development another methods, like powder and chemical method in latent fingerprint development. The high peak power of the laser causes Palmar sweat: contain a variety compounds, among them amino acids, oils, enzymes, vitamins and other chemicals with in the print to fluoresce. Some latent fingerprints will fluoresce in their natural state during exposure to this laser energy. The natural state fluorescing prints make can be documented and recording by high-resolution TV cameras and monitor for maximum sensitivity. The next step, the compare latent fingerprints products with visible impression by comparable instruments, see patterns of the friction ridges and be found same amount of their galton detail. "

"The purpose of this reserach is to find out the influence of laser shooting to the ovaries stem of eye,ablation of crab's eye to the level of egg's maruty,the diameter of eggs and the number of eggs scylla serrata....."

"Telah dilakukan suatu modifikasi pada sistem laser nitrogen untuk meningkatkan efisiensi pemakaian gas nitrogen dan daya keluaran laser. Modifikasi dilakukan pada bentuk elektrode dan konstruksi celah laser, sedemikian sehingga gas nitrogen yang dipakai sedikit (efisien) tapi daya keluaran tinggi. Sebagai pembanding digunakan konstruksi sistem laser nitrogen (sistem lama). Laser nitrogen yang dibuat (sistem baru) dapat dioperasikan pada daerah tegangan 7,48 kV sampai 10,30 kV. Sedangkan laser nitrogen (sistem lama) dapat dioperasikan pada daerah tegangan 6,96 kV sampai 11 kV. Optimalisasi dilakukan pada jarak antar elektroda celah laser 1,98 mm, tegangan keluaran penyedia daya 9,17 kV, debit aliran gas 7,3 liter/jam dan menggunakan cermin datar pada salah satu ujung keluaran laser. Diperoleh bahwa sistem laser (sistem baru) menghasilkan daya keluaran laser maksimal 3,3 mW. Sedangkan sistem laser (sistem lama) menghasilkan daya keluaran laser maksimal 0,6 mW. Kondisi optimum tegangan keluaran peyedia daya diperoleh pada tegangan 8,64 kV (sistem baru) dan pada tegangan 9,54 kV (sistem lama)."