Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 183203 dokumen yang sesuai dengan query
cover
Faris Fadli
"Di balik berbagai keunggulan metode stir casting, terdapat beberapa masalah di baliknya seperti kesulitan mencapai keseragaman distribusi penguat, keterbasahan penguat oleh lelehan logam, dan pembentukan porositas. Ketiga masalah ini dapat mengurangi kekuatan mekanis dari komposit yang dihasilkan. Oleh karena itu, ditemukan metode stir casting dua tahap untuk meningkatkan distribusi partikel dan mengurangi porositas dengan menambahkan penguat saat logam berada di fasa semi-padat. Pada penelitian ini dilakukan dua metode, yaitu metode konvensional dan dua tahap yang dikomparasikan pada komposit Al- 3Zn-1.6Mg berpenguat 7 % volume SiC untuk mengetahui pengaruhnya terhadap distribusi partikel dan pembentukan porositas akibat aglomerasi. Setelah pengecoran dengan metode stir casting konvensional dan dua tahap setelah itu komposit dihomogenisasi pada temperatur 400 °C selama 4 jam. Selanjutnya dilakukan karakterisasi berupa pengujian komposisi kimia, pengamatan struktur mikro menggunakan mikroskop optik, dan Scanning Electron Microscope (SEM) – Energy Dispersive Spectroscopy (EDS), pengujian kekerasan Rockwell, dan pengujian porositas. Penerapan metode stir casting dua tahap pada komposit mengecilkan ukuran SDAS menjadi 16.5 μm, meningkatkan jumlah volume SiC yang tercampur menjadi 7.63 %, menurunkan persentase porositas menjadi 1.33 %, dan meningkatkan nilai kekerasan menjadi 29 HRC. Peningkatan nilai kekerasan komposit metode stir casting dua tahap diakibatkan oleh ukuran SDAS yang lebih kecil, persentase porositas yang lebih sedikit, banyaknya volume SiC yang tercampur dalam matriks aluminium dan diikuti dengan distribusi yang baik, sehingga sangat sedikit ditemukan impregnation porosity.

Behind the various advantages of the stir casting method, there are several problems behind it such as difficulty in achieving uniform distribution of reinforcement, wettability of the reinforcement by molten metal, and the formation of porosity. These three problems can reduce the mechanical strength of the resulting composite. Therefore, a two-step stir casting method was found to improve particle distribution and reduce porosity by adding reinforcement when the metal is in the semi-solid phase. In this study, two methods were compared, namely the conventional method and the two-step method in an Al-3Zn-1.6Mg composite with 7 % volume SiC reinforcement to determine its effect on particle distribution and the formation of porosity due to agglomeration. After fabricated by two step stir casting method the composites were homogenized at 400 °C for 4 hours. Characterization was carried out in the form of chemical composition testing, microstructure observations byusing optical microscope, and Scanning Electron Microscope (SEM) – Energy Dispersive Spectroscopy (EDS), Rockwell hardness testing, and porosity testing. The application of the two-step stir casting method on composites reduced the SDAS size to 16.5 m, increased the volume of SiC mixed to 7.63 %, decreased the percentage of porosity to 1.33 %, and increased the hardness value to 29 HRC. The increase in the hardness value of the two-step stir casting method was caused by the smaller SDAS size, the smaller percentage of porosity, as well the large volume of SiC mixed in the aluminum matrix and followed by a good distribution, so that very little impregnation porosity was found."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Aziz
"Pembuatan komposit bermatriks aluminium dengan penguat abu terbang digunakan metode stir casting yang bertujuan untuk mereduksi terjadinya pembentukan pengelompokan penguat pada penguat abu-terbang. Peningkatan kekuatan matriks ditingkatkan dengan menambahkan magnesium. Pada penelitian ini, abu terbang menjadi variabel tetap dengan nilai volum fraksi sebesar 2.5% sedangkan magnesium dijadikan sebagai variabel peubah dengan variasi volum fraksi sebesar 1.5%, 3%, 4.5%, dan 6%. Setelah proses pengecoran, sampel diuji untuk melihat sifat mekanik yang terjadi akibat adanya perubahan volum fraksi dari magnesium. Pengujian mekanik yang digunakan berupa pengujian tarik, pengujian kekerasan, pengujian densitas dan porositas. Pengamatan struktur mikro serta scanning electron microscope (SEM) dengan electron dispersive X-Ray spectoscopy (EDX) digunakan sebagai pendukung untuk sifat mekanik yang terjadi pada komposit aluminium.

Fabrication of aluminum matrix composite with fly-ash as reinforce used liquid casting method to reduce the formation of fly-ash cluster. Aluminum matrix was enhanced by the addition of magnesium. In the study, fly-ash was a fixed variable with a value of the volume fraction of 2.5% hence magnesium was used as variables with variations in the volume fraction of 1.5%, 3%, 4.5%, and 6%. After fabrication, composite was tested to see the mechanical properties caused by changes in the volume fraction of magnesium. Mechanical testing were used in the form of tensile testing and hardness testing. Microstructure observation and scanning electron microscope (SEM) with electron dispersive X-Ray spectroscopy (EDX was used as a support for the mechanical properties of aluminum composite.
"
Depok: Fakultas Teknik Universitas Indonesia, 2015
S58698
UI - Skripsi Membership  Universitas Indonesia Library
cover
Vioni Dwi Sartika
"Pada penelitian ini dilakukan proses fabrikasi komposit Mg-Al-Sr sebagai matriks dengan penambahan penguat nano-SiC melalui metode pengecoran aduk. Penambahan fraksi volume penguat nano-SiC bervariasi yaitu sebesar 0.05 ; 0.10 ; 0.15 ; 0.20 , dn 0.25. Jika dibandingkan dengan paduan Mg-Al-Sr, penambahan partikel nano ke dalam matriks logam mampu meningkatkan sifat mekanik komposit yang dihasilkan. Penambahan fraksi volume nano-SiC sebesar 0.15 menghasilkan nilai kekerasan, harga impak, dan ketahanan aus paling optimum, serta disitribusi senyawa intermetalik yang terdispersi homogen di dalam struktur mikro. Hal ini disebabkan oleh semakin banyak penguat nano-SiC yang ditambahkan, maka aglomerasi cenderung meningkat sehingga proses penguatan menjadi kurang efektif. Karakterisasi komposit yang dilakukan adalah pengujian komposisi menggunakan OES, EDX, dan XRD; pengamatan struktur mikro menggunakan OM dan SEM; serta pengujian berupa pengujian kekerasan, impak, dan aus.

Magnesium composite with Mg Al Sr as the matrix reinforced by nano SiC particles have successfully fabricated by stir casting process. Addition of nano SiC into magnesium matrix varies by 0.05 0.10 0.15 0.20 and 0.25 in volume fraction. Compared with Mg Al Sr alloy, addition of nano particles into matrix improves mechanical properties of composites. It is observed that the optimum composition of nano SiC is 0.15 Vf which have the highest hardness value, impact toughness, and resistance to abrasion. It is also abserved that addition 0.15 Vf nano SiC modify the microstructure of composite by dispersing the intermetallic compound. The addition of Vf nano SiC could have tendency to agglomerate and strengthening mechanism is not effectively occurred. The result of chemical characterization using OES, EDX, XRD, metalloghraphy using OM and SEM, mechanical testing using hardness, impact, and abrasive testing."
Depok: Fakultas Teknik Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Nafis Dhaffarul Hannan
"Komposit merupakan material yang sedang dikembangkan, yang terdiri dari dua jenis material atau lebih untuk meningkatkan sifat mekanis. Komposit magnesium merupakan material yang cocok untuk dijadikan sebagai kerangka kendaraan karena magnesium merupakan logam yang memiliki nilai densitas paling rendah diantara logam lainnya sehingga dapat dihasilkan kerangka kendaraan yang ringan dengan sifat mekanik yang baik. Pada penelitian ini, komposit diciptakan dengan mencampurkan magnesium sebagai matriks dan nano SiC sebagai partikel penguat dengan penambahan fraksi volume sebesar 0.05 vf, 0.10 vf, 0.15 vf, 0.20 vf, dan 0.25 vf. Proses fabrikasi komposit magnesium ini adalah pengecoran aduk.
Hasil dari penelitian ini menunjukan dengan adanya penambahan nano SiC sebagai partikel penguat dapat meningkatkan sifat mekanis. Penambahan partikel penguat nano SiC yang menghasilkan komposit magnesium dengan sifat mekanis yang paling baik adalah penambahan dengan fraksi volume 0.010 vf yang menghasilkan nilai kekerasan sebesar 38.64 HB dan laju keausan sebesar 0.0106 mm3/m. Peningkatan sifat mekanis pada komposit magnesium disebabkan oleh pengecilan ukuran butir dan mekanisme penguatan Orowan.

Composites are advanced material which is being developed that contains of two materials or more in order to improve the mechanical properties. Magnesium composite is a suitable material to be applicated as vehicle body structure due to its lightweight and its low density. Thus, the vehicle body structure with lightweight and good mechanical properties can be achieved. In this research, magnesium composite is fabricated by mixing magnesium as composite matrix and nano SiC as reinforcement particle with the variation of the volume fraction 0.05 vf, 0.10 vf, 0.15 vf, 0.20 vf, and 0.25 vf with stir casting as fabrication methods.
The result of this research shows that with nano SiC addition as reinforcement particle will increase mechanical properties of magnesium composite. The best mechanical properties of magnesium composite is shown by the addition of 0.10 vf nano SiC. The result shows the brinnel hardness number of this composition is 38.64 HB and 0.0106 mm3 m wear rate. Mechanical properties of magnesium composite are increased due to several strengthening mechanism such as grain size reduction and Orowan strengthening mechanism.
"
Depok: Fakultas Teknik Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Lumban Tobing, Basauli Tiarma Olivia Br.
"[Penelitian kali ini adalah berfokus pada penguatan matriks guna mendukung sifat optimum material komposit. Penguatan matriks dilakukan dengan penambahan Al-5Ti-1B dan Al-15Sr sebagai pemodifikasi matriks serta penambahan Mg sebanyak 10 wt% sebagai agen pembasahan pada komposit. Penambahan unsur modifikasi, seperti Al-5Ti-1B bertujuan sebagai agen penghalus butir dan Al-15Sr sebagai pemodifikasi dari senyawa fasa kedua yang terbentuk pada matriks paduan aluminium. Komposit pada penelitian kali ini mencapai sifat optimum pada penambahan Ti dan Sr menjadi 0.031 wt% dan 0.06 wt%. Kehadiran unsur Ti dan Sr yang ditambahkan dalam paduan matriks menghasilkan bentuk dendrit yang
terfragmentasi menjadi globular yang halus dengan dispersi fasa yang diduga adalah Mg2Si dalam morfologi chinese script yang bertransformasi menjadi fibrous kecil dan halus. Selain itu juga tidak ditemukannya fasa berbentuk
jarum atau platelet yang tajam yang berkontribusi terhadap deteorisasi dan penggetasan, seperti Al3Fe dalam paduan ini. Struktur yang dimiliki oleh komposit ini dianggap menjadi struktur yang baik untuk menunjang karakteristik matriks. Hal ini dipercaya sebagai alasan tingginya nilai
kekuatan tarik serta keuletan yang dimiliki material. Lalu, permukaan patahan pada komposit ini juga menunjukkan kombiinasi dari patah ulet dan getas.

The research is focused on the strengthening process of the matrix to give an outstanding characteristic of composite material. Strengthening the matrix is done by modification of Al-5Ti-1B dan Al-15Sr addition with 10 wt% Mg addition as the wetting agent. Addition of Al-5Ti-1B acts as grain refinement agent which provide more nucleating siteand restrict the growth of grains and
Al-15Sr acts as modifiers of the morphology of the second phase particles. The optimization of the composite characteristics is also followed by the maintenance of the casting process which is followed by degassing process.
After the casting process is done, the examination of mechanical properties, chemical composition and examination of the microstructure will be held. The optimum composition of the composite in this research is on the addition of Ti and Sr to be 0.031 wt% dan 0.06 wt%. These elements added to matrix give the fragmented dendritic-like structure of the (Al) as the matrix with the second phases, Mg2Si dispersed in the matrix have the fine morphology also. Then, there is observed no deteoriation morphology of phases like Al3Fe which is used to be needle like or platelet like. This morphology structure is considered to the best and wanted structure to the matrix and will give optimum characteristics. It is considered that this morphology of the composite is the reason of achieving highest UTS along with increasing in
ductility. In the observation of the fractograph, it is found that the mode of fracture is categorized to be the combination of ductile and brittle fracture mode., The research is focused on the strengthening process of the matrix to give an
outstanding characteristic of composite material. Strengthening the matrix is
done by modification of Al-5Ti-1B dan Al-15Sr addition with 10 wt% Mg
addition as the wetting agent. Addition of Al-5Ti-1B acts as grain refinement
agent which provide more nucleating siteand restrict the growth of grains and
Al-15Sr acts as modifiers of the morphology of the second phase particles.
The optimization of the composite characteristics is also followed by the
maintenance of the casting process which is followed by degassing process.
After the casting process is done, the examination of mechanical properties,
chemical composition and examination of the microstructure will be held.
The optimum composition of the composite in this research is on the addition
of Ti and Sr to be 0.031 wt% dan 0.06 wt%. These elements added to matrix
give the fragmented dendritic-like structure of the (Al) as the matrix with the
second phases, Mg2Si dispersed in the matrix have the fine morphology also.
Then, there is observed no deteoriation morphology of phases like Al3Fe
which is used to be needle like or platelet like. This morphology structure is
considered to the best and wanted structure to the matrix and will give
optimum characteristics. It is considered that this morphology of the
composite is the reason of achieving highest UTS along with increasing in
ductility. In the observation of the fractograph, it is found that the mode of
fracture is categorized to be the combination of ductile and brittle fracture
mode.]
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
S62217
UI - Skripsi Membership  Universitas Indonesia Library
cover
Michelle Julia Halieman
"Saat ini tren penggunaan material komposit meningkat secara drastis. Komposit aluminium merupakan salah satu material yang dikenal luas karena memiliki sifat mekanis yang baik. Pada studi literature ini, akan ditunjukkan hasil dari beberapa studi mengenai komposit aluminium dengan penambahan penguat nano alumina melalui proses pengecoran yang diikuti dengan perlakuan panas sebagai alternatif dalam berbagai aplikasi salah satunya sebagai material kampas rem yang umumnya menggunakan material besi tuang cor. Komposit yang telah dimaufaktur diberi perlakuan T6 yang meliputi tahapan solution treatment, quenching, dan artificial aging dengan tujuan untuk mengoptimalkann performa material seperti kekuatan Tarik, ketahanan aus, nilai kekerasan, dan ketahanan impak. Untuk mengetahui lebih lanjut pengaruh age hardening, dilakukan analisis perbandingan material komposit dengan kondisi pengecoran dan setelah penambahan perlakuan T6 dengan pengujian menggunakan mikroskop optik dan SEM-EDS serta pengujian sifat mekanis. Hasilnya menunjukkan adanya peningkatan sifat mekanis pada material komposit setelah perlakuan T6 dibandingkan dengan komposit hasil pengecoran akibat peristiwa precipitation hardening. Dibandingkan dengan material besi tuang cor, sifat mekanis komposit aluminium berpenguat nano alumina dengan perlakuan T6 lebih baik sehingga material ini cocok digunakan untuk menggantikan besi tuang cor sebagai aplikasi kampas rem.
The trend towards the use of composites is currently increasing rapidly nowadays. Aluminium composites is one of the most popular material due to their good mechanical properties. This review reports the results from several studies on Nano alumina reinforced AC4B (Al-Si-Cu) aluminium through the casting process followed by heat treatment as an alternative material in any application such as brake shoe which usually made of grey cast iron. The manufactured composite treated by T6 treatment with 3 stages involve solution treatment, quenching and artificial aging to optimize its performance such as tensile strength, wear resistance, hardness value, and impact resistance. In order to investigate the effect of age hardening response, microstructural analysis was carried out by Light Microscope and SEM-EDS and several mechanical properties tests were analysed in their as cast condition and after the solution heat treatment and aging process. The results showed that the mechanical properties of aluminium composite applied with T6 treatment were increased compared to unheat treated AC4B /nano alumina composite caused by the precipitation hardening. Compared to grey cast iron, mechanical properties of aluminium composite reinforced nano alumina followed by T6 is higher. In conclusion, aluminium composite reinforced nano alumina with T6 is suitable for brake shoe application."
Depok: Fakultas Teknik Universitas Indonesia , 2020
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Reza Prima Naufal
"Komposit sandwich adalah material yang banyak diaplikasikan dalam berbagai industri, struktur bangunan, dan moda transportasi. Komposit sandwich memiliki kekuatan yang tinggi, massa yang ringan, dan dapat dibentuk dengan mudah. Tujuan penelitian ini adalah membandingkan sifat mekanik (sifat tarik, sifat lengkung, dan sifat tekan) komposit sandwich dengan inti busa PU dan kulit epoksi diperkuat woven roving fiberglass, yang difabrikasi dengan teknik cold press-adhesif (ADS) dan VARI (vacuum assisted resin infusion). Pengukuran densitas, pengujian tarik, lentur dan tekan dilakukan dalam penelitian ini. Pengamatan permukaan sampel dilakukan untuk mengetahui kerusakan yang terjadi pada sampel setelah pengujian mekanik. Densitas komposit sandwich memiliki nilai yang relatif sama, yaitu sebesar (0,25 ± 0,01) g/cm3 untuk komposit VARI dan sebesar (0,27 ± 0,01) g/cm3 untuk komposit ADS. Kuat tarik sampel ADS, (1,96 ± 0,28) MPa, memiliki nilai yang lebih tinggi dibandingkan kuat tarik sampel VR; sedangkan kuat lengkung sampel VR, (11,70 ± 1,98) MPa, memiliki nilai yang lebih tinggi. Kuat tekan kedua sampel memiliki nilai yang relatif sama yaitu (1,36 ± 0,45) MPa untuk sampel VR dan (1,32 ± 0,02) MPa untuk sampel ADS. Kerusakan yang terjadi pada komposit sandwich berupa kerusakan pada inti busa PU, dan delaminasi pada kulit dari komposit sandwich.

Sandwich composites are widely applicated materials in various industries, building structure, and transportation. Sandwich composites have high strength value, lightweight, and can be fabricated easily. The purpose of this research was to compare the mechanical properties (tensile, flexural, and compressive strengths) of sandwich composite with polyurethane foam as a core and woven roving fiberglass reinforced epoxy as skins, which were fabricated using cold press-adhesive (ADS) and VARI (vacuum assisted resin infusion). Density measurement, tensile, flexural, and compressive tests were carried out in this research. Sample surface observation was carried out to determine the damage that occurred to the samples after mechanical tests. The densities of both composites had relatively the same values, (0,25 ± 0,01) g/cm3 for VR sandwich composite and (0,27 ± 0,01) g/cm3 for ADS sandwich composite. The tensile strength of ADS sandwich composite, (1,96 ± 0,28) MPa, had a higher value than that the VR sandwich composite sample, while the flexural strength of VR sandwich composite, (11,70 ± 1,98) MPa, had a higher value than that the ADS sandwich composite. Compressive strength of both sandwich composites had relatively the same values (1,36 ± 0,45) MPa for VR sandwich composite and (1,32 ± 0,02) MPa for ADS sandwich composite. The damage occurred in the PU foam core, and delamination occurred in the skin of the sandwich composites."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Yosia Samuel
"Proses fabrikasi komposit matriks aluminium dapat dilakukan melalui fasa cair dengan menggunakan metode stir casting untuk meminimalisir terbentuknya clustering penguatSiC. Metode ini memiliki keuntungan dalam hal distribusi penguat SiC dengan bantuan magnesium sebagai wetting agent. Dalam hal ini magnesium berfungsi meningkatkan kemampu-basahan antara matriks aluminium dan partikel penguat SiC. Pada penelitian ini dilakukan variasi penambahan penguat SiC sebesar 5% wt, 10% wt, dan 15% wt dengan kadar magnesium tetap 1,5% wt. komposit matriks aluminiumdiberi perlakuan berbeda yaitu kondisi as-cast dan T6 heat-treated dengan perbedaan sifat mekanis.
Hasil penelitian menunjukkan bahwa penambahan penguat SiC meningkatkan nilai kekerasan dan menurunkan laju aus. Proses perlakuan panas T6 pada komposit matriks aluminium meningkatkan nilai sifat-sifat mekanik dibandingkan pada kondisi as-cast akibat terbentuknya presipitat sekunder pada kondisi T6 heat-treated. Penambahan fraksi berat penguat SiC pada komposit matriks aluminium juga meningkatkan persen porositas. Persen porositas ini dapat dilihat melalui penurunan nilai densitas aktual komposit matriks aluminium dibandingkan densitas teoritisnya.

Fabrication of aluminum matrix composite can be done through liquid phase by using stir casting method in order to minimalizing the formation of SiC clustering penguat. This method has the advantage in the distribution of SiC reinforce with the function of magnesium as wetting agent. In this case, magnesium will increase the wettability between aluminum matrix and the SiC reinforce particle. This research focus on the addition of SiC reinforce in the amount of 5% wt, 10% wt, and 15% wt with a fix amount of magnesium, 1,5% wt. The aluminum matrix composite is given by different treatment, as-cast condition and T6 heat treated with different mechanical properties.
The result shows that the addition of SiC reinforce will increase the hardness value and decrease the wear rate value of aluminum matrix composite. T6 heat treatment process in aluminum matrix composite increase the mechanical properties value greater than the as-cast condition as the formation of secondary precipitate in T6 heat-treated condition. The addition of SiC reinforce weight fraction in aluminum matrix composite also increase the porosity percentage. This porosity percentage can be observed by the decreasing value of actual density aluminum matrix composite compared by theoritical density.
"
Depok: Fakultas Teknik Universitas Indonesia, 2012
S43249
UI - Skripsi Open  Universitas Indonesia Library
cover
Aninda Fitriandini
"Perkembangan teknik dan perangkat radioterapi yang sangat pesat membuat AAPM TG-51dan TRS 398 selaku protokol dosimetri konvensional menjadi kurang relevan untuk digunakan. Pada tahun 2008, Alfonso, dkk. kemudian memperkenalkan formalisme baru untuk menghasilkan faktor koreksi kualitas berkas lapangan nonstandar, baik statik maupun komposit untuk meminimalisir perbedaan antara kondisi kalibrasi dan aktual. Tujuan utama penelitian ini adalah mempelajari dan menentukan faktor koreksi lapangan komposit kpcsr,msr dan kclin,pcsr dari pesawat Tomotherapy pada kasus kanker kepala dan leher, pelvis, dan otak, serta mengimplementasikannya pada proses DQA. Pengukuran faktor koreksi dilakukan pada Exradin A1SL dan A16, menggunakan film EBT3 sebagai dosimeter referensi. Hasil dari penelitian ini menunjukkan bahwa nilai faktor koreksi kpcsr,msr pada kedua detektor meningkat seiring dengan peningkatan jaw, penurunan kompleksitas lapangan, dan peningkatan nilai pitch. Beberapa hal fisis yang mempengaruhi nilai faktor koreksi antara lain homogenitas target, volume averaging effect, thread effect, dan perbedaan besar rekombinasi umum pada jaw yang berbeda. Hasil ini menunjukkan bahwa nilai faktor koreksi kpcsr,msr bersifat spesifik dan bergantung pada parameter pembuatan lapangan. Oleh karenanya, lapangan pcsr sebaiknya ditentukan sesuai dengan kondisi klinis yang digunakan. Implementasi faktor koreksi kclin,pcsr untuk DQA pada kasus kanker kepala dan leher menunjukkan adanya perubahan deviasi antara dosis terkalkulasi dan terukur hingga 3 .

The rapid development of radiation therapy techniques and devices cause TG 51 and TRS 398 as conventional dosimetry protocols become less relevant for clinical dosimetry. In 2008, Alfonso, et al. introduced new formalism to produce correction factors for nonstandard field static and composite field to minimize the difference between calibration and actual conditions. The purpose of this work is to investigate and determine the correction factor of composite field from Tomotherapy for several cases H N, pelvis and brain cancer, and to implement it in DQA process. Measurements were performed using Exradin A1SL and A16, using EBT3 film as reference dosimeter. The results indicate that the value of kpcsr,msr on both detectors increased with increasing field width, decreasing field complexity, and increasing pitch value. Several factors that affect the correction factor were indicated in this work target homogeneity, volume averaging effect, thread effect, and large difference of general recombination on different jaws. These results show that kpcsr,msr is specific and depends on the parameters of composite field. Therefore, the pcsr field should be determined according to the parameters used in clinical conditions. Implementation of kclin,pcsr for DQA in H N cancer showed a change in deviation between the calculated and measured doses up to 3 ."
Depok: Universitas Indonesia, 2018
T50624
UI - Tesis Membership  Universitas Indonesia Library
cover
Amalia Tri Wahyuni
"Rem memiliki peran sangat penting karena dapat mengatur laju kendaraan. Rem adalah suatu sistem ketahanan gesekan buatan yang diaplikasikan pada sesuatu yang bergerak (moving member) untuk memperlambat atau menghentikan pergerakannya dengan menyerap energi kinetik dan menghilang dalam bentuk panas ke atmosfer sekitar. Cakram rem memerlukan material dengan kekerasan dan kekuatan tekan tinggi serta ketahanan aus dan konduktivitas termal yang baik, maka dari itu cakram rem biasanya terbuat dari besi tuang, namun dapat juga terbuat dari bahan komposit, seperti karbon, Ceramic Metal Composite (CMC), dan Metal Matrix Composite (MMC). Penelitian ini mempelajari pengaruh penambahan penguat pada komposit matriks aluminium terhadap struktur mikro, sifat mekanis, dan ketahanan aus untuk aplikasi cakram rem. Fokus pada penelitian ini adalah matriks komposit Al-11Zn-5Mg dengan variasi 0 dan 10 vol.% kadar SiC yang dibuat dengan metode squeeze casting. Pemilihan SiC sendiri diharapkan dapat menjadi penguat untuk peningkatan pengerasan pada matriks komposit tersebut. Selanjutnya dilakukan laku panas dimulai dari laku pelarutan pada temperatur 450 °C selama 1 jam diikuti dengan pendinginan cepat, kemudian dilakukan penuaan pada temperatur 200 °C selama 2 jam. Pengujian yang dilakukan pada penelitian ini adalah pengujian komposisi kimia, pengamatan struktur mikro, x-ray mapping, dan SEM – EDS (Scanning Electron Microscope – Energy Dispersive Spectroscopy), pengujian XRD (X-Ray Diffraction), perhitungan porositas dan DAS (Dendrite Arm Spacing), pengujian kekerasan, impak, dan laju aus. Hasil pengujian menunjukkan penambahan SiC 10 vol.% meningkatkan nilai kekerasan komposit dari 72.1 HRB menjadi 79.5 HRB. Fasa yang terbentuk setelah penuaan adalah fasa MgZn2, Mg2Zn11, Fe-Al intermetalik, MgAl2O4, dan Mg2Si. Laju keausan meningkat pada penambahan beban, yaitu masing-masing sebesar 4.27 x 10-3 mm3/m, 10.19 x 10-3 mm3/m, dan 22.33 x 10-3 mm3/m pada beban 2.11, 6.32, dan 18.96 kg pada sampel tanpa penambahan SiC. Namun, laju keausan secara signifikan lebih rendah pada sampel komposit yang mengandung 10 vol.% SiC, yaitu 2.78 x 10-3 mm3/m, 7.26 x 10-3 mm3/m, dan 19.93 x 10-3 mm3/m pada beban 2.11, 6.32, dan 18.96 kg.
.....Brakes have a very important role because they can regulate the speed of the vehicle. Brake is an artificial friction resistance system that is applied to something that is moving (moving member) to slow down or stop its movement by absorbing kinetic energy and dissipating it in the form of heat to the surrounding atmosphere. Brake discs require materials with high hardness and compressive strength as well as wear resistance and good thermal conductivity, therefore brake discs are usually made of cast iron, but also can be made of composite materials, such as carbon, Ceramic Metal Composite (CMC), and Metal Matrix Composite (MMC). This research studied the effect of adding strengthening to the aluminium matrix composite on the microstructure, mechanical properties, and wear resistance for brake disc applications. The focus of this research is the Al-11Zn-5Mg composite matrix with variations of 0 and 10 vol.% SiC content made by squeeze casting method. The selection of SiC itself is expected to be a strengthening material for increasing the hardening of the composite matrix. The samples were heat treated starting from the dissolution treatment at 450 °C temperature for 1 hour followed by rapid cooling, then aging at 200 °C temperature for 2 hours. The tests carried out in this research were chemical composition testing, microstructure observations, x-ray mapping, and SEM-EDS (Scanning Electron Microscope – Energy Dispersive Spectroscopy), XRD (X-Ray Diffraction) testing, porosity and DAS (Dendrite Arm Spacing) calculations, hardness testing, impact, and wear rate. The test results showed the addition of SiC 10 vol.% obtained higher composite hardness values, which were 72.1 and 79.5 HRB after aging, respectively. The phases formed after aging are MgZn2, Mg2Zn11, intermetallic Fe-Al, MgAl2O4, and Mg2Si phases. The wear rate increases with increasing load, which were 4.27 x 10-3 mm3/m, 10.19 x 10-3 mm3/m, and 22.33 x 10-3 mm3/m respectively at 2.11, 6.32, and 18.96 kg loads in the sample without the SiC addition. However, the wear rate was significantly lower in the composite samples containing 10 vol.% SiC, namely 2.78 x 10-3 mm3/m, 7.26 x 10-3 mm3/m, and 19.93 x 10-3 mm3/m at a load of 2.11, 6.32, and 18.96 kg."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>