Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 75799 dokumen yang sesuai dengan query
cover
Heri Nugraha
"Inhomogenitas termoelektrik memiliki kontribusi yang besar terhadap nilai ketidakpastian dalam kalibrasi termokopel. Oleh karena itu, untuk mengetahui ketidakhomogenan pada termokopel perlu dilakukan pemindaian pada kawat termokopel untuk menentukan karakteristik koefisien Seebeck pada setiap posisi termokopel berrdasarkan pengaruh paparan suhu di sepanjang termokopel. Pada penelitian ini dikembangkan metode pengukuran inhomogenitas pada kawat termokopel tipe T dan K dengan melakukan pemindaian termokopel pada suhu 120 oC dan 300 oC dengan metode pemanasan lokal atau double gradient system dengan penambahan sensor pemantauan suhu dan desain blok pemanas tambahan untuk meminimalkan luas area pemanasan lokal. Hasil pengukuran kemudian divalidasi dengan metode pada bak cairan atau single gradient system. Metode pemanasan lokal berpotensi untuk mengukur rentang yang lebih panjang variasi dari ketidakseragaman koefisien Seebeck (µV/oC) sepanjang kawat termokopel berbeda dengan pengukuran pada bak cairan yang terbatas jarak pemindaiannya. Hasil pengukuran menunjukan nilai koefisien Seebeck inhomogenitas pada kedua tipe termokopel relatif tidak berubah pada suhu 120 oC, sedangkan pada suhu 300 oC terdapat perubahan koefisien Seebeck. Sistem ini juga dapat mendeteksi titik-titik tertentu pada termokopel yang memiliki inhomogenitas dengan sangat jelas karena terdepresinya koefisien Seebeck, serta dapat menentukan keseragaman atau ketidakseragaman pada kawat termokopel berdasarkan pola distribusi tegangan pada termokopel. Sistem dapat mengukur inhomogenitas dibawah 0.1% yang merupakan standar ketidakpastian pada termokopel base-metal dan tervalidasi dengan metode pada bak cairan. Sehingga dengan kemampuan tersebut, sistem telah memenuhi untuk dapat digunakan dalam mengukur ketidakseragaman termokopel tipe base-metal.

.Thermoelectric inhomogeneity constitutes a major contribution to the calibration uncertainty of a thermocouple sensor. Therefore to investigate the inhomogeneity of the thermocouple it is necessary to scan the thermocouple wire to measure the Seebeck coefficient characteristic in each wire position based on the effect of temperature exposure along the thermocouple wire. In this study, a method of measuring the inhomogeneity of type T and K thermocouple wires was developed by scanning the thermocouple at temperatures of 120 oC and 300 oC with local heating method where also known as a double gradient method. The proposed system utilized with a temperature monitoring sensors and reducing the nozzle diameter of the heating source output also with an additional heat block design to minimize the area of local heating. The measurement result then compared with the single gradient method using a liquid bath as a validation. The local heating method has the potential to measure more longer range the variability of the Seebeck coefficient (µV/oC) along the length of the thermocouple wire different from the measurement in a liquid bath which has limited scanning distance. The measurement results show that the Seebeck coefficient of inhomogeneity in the two types of thermocouple is relatively unchanged at 120 oC, while at 300 oC the coefficient has changed. This system also could detected a certain points on the thermocouple which have very clear inhomogeneity due to depressed Seebeck coefficient, also determine the uniformity or non-uniformity of the thermocouple wire based on the voltage distribution on the thermocouple. The system can measure to a non-uniformity of less than 0.1% which is typical for new base-metal thermocouples. The value is agreed validate with the measurement results using the single zone method. So, with this capability the system has met to be used in measuring the non-uniformity of the base-metal thermocouple."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2020
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
cover
Fakhrurrozi
"Seiring dengan pesatnya penggunaan kamera pengawas di dalam maupun di luar gedung , maka dalam beberapa tahun terakhir berkembang teknik pendeteksian asap memanfaatkan CCD camera berbasis computer vision. Namun tidak begitu jelas atas dasar apa nilai treshold harus ditetapkan untuk memenuhi persyaratan keselamatan. Penelitian ini mencoba melanjutkan pengembangan sistem deteksi asap berbasis video dengan mencari karakter dari asap, baik secara fisik (optical density) maupun berbasis citra, dari berbagai material jenis polimer. Kemudian akan dicari korelasi antara karakteristik asap secara fisik terhadap karakteristik asap berbasis pengolahan citra, untuk dapat meningkatkan akurasi sistem deteksi asap berbasis video.

Following the rapid expansion of surveillance video camera inside or outside the building, the development of smoke detection based on computer vision has increase as well in recent years. But it is still not very clear on what basis the threshold value of detection system for image processing should be set to meet the safety requirement. This research attemp to continue the development of smoke video detection by search for the characteristics of the smoke itself, physically (optical density) as well as digital imaging, from a variety of polymer materials. Afterwards this research will find out the correlation between them, in order to improving video smoke detection accuracy."
Depok: Fakultas Teknik Universitas Indonesia, 2011
S43460
UI - Skripsi Open  Universitas Indonesia Library
cover
Verra Syahmer
"Rendahnya kualitas perkuliahan dapat mengakibatkan ketidakpuasan mahasiswa. Oleh karena itu diperlukan pengidentifikasian atribut kualitas perkuliahan yang kemudian dikelompokkan menjadi beberapa faktor menggunakan analisis faktor serta pemodelan hubungan kualitas perkuliahan dengan kepuasan mahasiswa menggunakan analisis regresi berganda. Analisis penelitian ini dilakukan menggunakan data primer yang didapatkan dari penyebaran kuesioner kepada mahasiswa S1 Universitas Indonesia sebagai sampel penelitian. Setelah melakukan analisis, teridentifikasi 6 faktor kualitas perkuliahan yang dapat mempengaruhi kepuasan mahasiswa, namun hanya dua diantaranya yang berpengaruh secara signifikan, yaitu faktor kemampuan dosen menyampaikan materi dan kondisi bangunan dan ruang kelas. Jika memperhatikan tingkat kepuasan mahasiswa, faktor yang menjadi prioritas adalah kemampuan dosen menyampaikan materi.

Low quality of lecture can cause students dissatisfaction. Therefore, it is necessary to identified the attribute of quality of lecture, then grouped into several factors using factor analysis and modelling relations between quality of lecture and student satisfaction using multiple regression analysis. Analysis of this study use primary data obtained from the questionnaire to undergraduate students of University of Indonesia as the sample. After doing an analysis, 6 factors are identified as a matter of student satisfaction on quality of lecture, but only two factors significantly influence, there are lecturer ability given the lecture and the condition of buildings and classrooms. If we see the level of student satisfaction, the priority factor is the lecturer ability given the lecture.
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
T46267
UI - Tesis Membership  Universitas Indonesia Library
cover
cover
Fauzun
"This research was done to investigate influence of the base metal surface roughness on the BAg-8 spreading behavior and to get a proper surface roughness number for large area brazing. The filler metal was melted at 830o C for 15 minutes on a S50C surface for with various roughness levels. After solidified, the spreading area was observed and characterized in macro and micro scale. The results show that physically the filler spreading consists of two kinds of spreading forms: true and apparent filler spreading with composition of the both being almost same; 77% Ag and 23% Cu. For some roughness numbers, irregularities in uniformity of the heating and cooling process on the filler and dissolving of contaminant into the molten filler caused the true spreading that tend to separate became several parts and tend to flow out from initial placement. Increasing of the surface roughness tends to increase the capillarity effect and to decrease imbalance in the surface tension. Optimum surface roughness was obtained at Rz = 0.92. At this number, the ratio, as well as fitness of the true spreading with initial condition, was at the maximum. During the application process, this condition is predicted as being able to prevent or avoid weaknesses in the joint, thereby increasing the joint strength and its appearance quality."
Depok: Faculty of Engineering, Universitas Indonesia, 2011
UI-IJTECH 2:3 (2011)
Artikel Jurnal  Universitas Indonesia Library
cover
Muhamad Farid Abdillah
"Salah satu gangguan keamanan jaringan yang ada pada teknologi Wifi adalah adanya perangkat Rogue Access Point (RAP), yang merupakan Access Point yang tidak dilegitimasi oleh administrator jaringan. Deteksi terhadap keberadaan RAP sudah banyak dikembangkan dengan berbagai metoda. Salah satunya adalah deteksi RAP menggunakan aplikasi berbasis web yang tidak memerlukan asistensi dari administrator jaringan. Sistem ini menggunakan waktu Round Trip Time dari DNS lookup dan DHCP request sebagai parameter untuk mendeteksi keberadaan RAP.
Hasil pengujian menunjukkan bahwa pada RAP diperoleh RTT DNS lebih lama dibandingkan RTT DHCP sebagai konsekuensi adanya hop tambahan. Tingkat akurasi sistem dipengaruhi oleh trafik pada RAP dan beban pada legitimate AP, semakin tinggi trafik pada RAP dan beban pada AP semakin berkurang keakuratan sistem. Implementasi sistem berhasil dilakukan dengan tingkat akurasi pendeteksian sistem mencapai 98,2% pada kondisi trafik idle, kemudian menurun menjadi sekitar 88,9% pada kondisi trafik medium dan turun lagi menjadi sekitar 70,3% pada kondisi trafik tinggi.

Rogue Access Point (RAP) is one of the vulnerabilities in Wifi technology, which is an Access Point that is not legitimated by the network administrator. The detection of RAP has been developed widely with various methods. A Method that has been developed in this study is the RAP detection using web based aplication which does not require network administrator assistant. This system uses Round Trip Time of DNS lookup and DHCP request as parameters that will be used for detecting the existence of RAP.
The test shows that on RAP the DNS RTT will be longer than the DHCP RTT as the consequensies of the addition of hop. The system's accuracy is influenced by the WiFi traffic and load on legitimate AP, the bigger the traffic and the load make the system's accuracy more decreased. The system accuration level is 98,2% on idle traffic, decrease to 88,9% when the traffic is medium and become 70,3% on high traffic condition.
"
Depok: Fakultas Teknik Universitas Indonesia, 2011
T29551
UI - Tesis Open  Universitas Indonesia Library
cover
Chandra Jumawa
"ABSTRAK
Teknologi dan metode pengukuran merupakan salah satu hal yang fundamental dalam riset maupun dalam pendidikan. Tingkat keakurasian pengukuran sangat diperhatikan pada suatu alat ukur. Dan pengukuran temperatur adalah pengukuran yang sering digunakan, karena sifat panas yang selalu ada dalam tiap objek di bumi. Dalam mengukur temperature diperlukan alat ukur yang akurat dan presisi, salah satunya adalah termokopel dan RTD. Termokopel memiliki tipe berdasarkan logam pembentuknya, sehingga kemampuan pengukurannya pun berbeda. Namun tiap termokopel berlandaskan pada hukum seebeck , dimana dua logam dibuat menyatu dengan tiap ujungnya mengukur pada temperatur yang berbeda sehingga menimbulkan gaya gerak listrik. Untuk itu sambungan ujung termokopel perlu diperhatikan agar mendapatkan performa terbaik. Terdapat tiga jenis macam dalam penyambungan dalam penelitian ini yaitu sambungan tik, lilit, dan solder, yang masing-masing jenis sambungannya dilakukan pada termokopel tipe J, T, dan K pada rentang diameter 0,2−0,7 𝑚𝑚.. Sambungan tik menunjukkan tingkat kesesuaian yang lebih baik dibanding solder pada termokopel dengan logam berdiameter kecil. Sedangkan pada logam berdiameter besar , sambungan solder menunjukkan tingkat kesesuaian linieritas yang lebih baik. Simpangan rata-rata paling kecil ditunjukkan pada tipe sambungan solder. Dan pengukuran temperatur pada ambien memberikan hasil delta temperatur yang berbeda antar termokopelnya selama satu hari penuh, dimana pada rentang waktu tertentu terdapat delta perubahan yang lebih rendah dibanding rentang waktu lain. Serta termokopel lebih akurat dibanding RTD ketika mengukur temperature pada rentang −200−2000𝐶.

ABSTRACT
Technology and method of measurement is one of fundamental thing in doing research and study. Accuracy in measurement instrument is being concerned to obtain valid data. Temperature measurement is widely used in research as a result of heat transfer process in objects. In temperature measurement, high accuracy instrument is needed. One of the temperature measurement instrument is called thermocouple. Thermocouple has different type based of forming material. This material difference will affect their characteristic. Every thermocouple works based on the seebeck effect, which say that if junctions from two different metal wire are created and has temperature difference, there will be electromotive force. For that reason junction tip of thermocouple must be observe to get better perform. The method of creating junction has three variation, the first method is tik, the second method is twist, and the other is soldered. Concentration will be put on type J, K, T type thermocouple, method of creating junction by tik, twist, soldered, and variety of thermocouple diameter between 0, 2 to 0, 7mm. The result of this experiment gives that tik junction indicates better level of concordance than soldered junction at little wire. However, soldered junction shows better level of concordance at thick wire. Average deviation of soldered junction shows better than other while in measure ambient temperature for one day. And thermocouple shows better than RTD while in use between −200 to 2000𝐶."
Fakultas Teknik Universitas Indonesia, 2014
S54051
UI - Skripsi Membership  Universitas Indonesia Library
cover
"Pengukuran suhu dilakukan dengan mengkonversikan beda tegangan yang timbul karena adanya perubahan suhu di sekitar sensor. Karena beda tegangan thermocouple hanya sebanding dengan perbedaan suhu antara simpul ukur dan simpul acuan thermocouple, maka diperlukan sensor lain untuk mengukur suhu simpul acuan.
Jadi hasil akhir pengukuran merupakan penjumlahan antara suhu basil konversi beda tegangan thermocouple dan suhu hasil konversi sensor pengukur suhu simpul acuan, dalam hal ini LM-35. Beda tegangan kedua sensor tersebut dibu$er, dikuatkan, dan dijumlah, sampai memenuhi kondisi tertentu sehingga perubahan beda tegangan karena perubahan suhu dapat d identifikasi oleh wialog input interface card_ Pada kartu interface ini, beda tegangan disampling menjadi data digital 8 bit. Data ini diambil oleh komputer melalui IC PPI pads kartu interface tersebut. Data hasil pengambilan dari analog input interface card dikonversikan dalam bentuk besaran suhu, dan dijumlahkan, sehingga hasil pengukuran merupakan suhu pada simpul ukur thermocouple. Kalibrasi sensor dilakukan dengan terlebih dahulu mengkalibrasi sensor simpul acuan (LM-35) pads suhu 0_C, baru kemudian mengkalibrasi thermocouple pada suhu tertentu. Pengambilan dan penyimpanan data suhu dilakukan secara kontinyu dengan interfal waktu satu detik, sehingga akan memudahkan proses pelaporan dan pemeriksaan data. Dengan memberikan batasan pengukuran pada masing-masing sensor, diberikan suatu algoritma dimana masing-masing sensor akan saling memeriksa harga suhu pengukuran sensor pasangannya. Alarm kondisi sensor akan menyala jika terdapat kejanggalan harga suhu salah satu sensor terhadap sensor pasangannya."
Fakultas Teknik Universitas Indonesia, 1997
S38891
UI - Skripsi Membership  Universitas Indonesia Library
cover
Affan Hifzhi
"Difusi yang terjadi di antara dua buah cairan dengan konsentrasi berbeda akan menghasilkan gradien indeks bias yang beragam. Sebuah alat untuk mengamati difusi antar dua cairan tersebut telah dibuat dengan menggunakan metode defleksi sinar laser. Pola defleksi sinar laser terjadi akibat adanya pembiasan cahaya ketika memasuki daerah perbatasan antara dua cairan dengan indeks bias yang berbeda. Koefisien difusi dapat ditentukan dengan mengamati gradien indeks bias yang terjadi pada area batas kedua cairan. Dalam fenomena ini, transfer massa yang ditunjukkan oleh nilai koefisien difusi dari satu cairan menuju cairan lain memiliki peranan penting dan dapat dijelaskan dengan menggunakan hukum Fick. Eksperimen difusi telah dilakukan menggunakan cairan NaCl dan Aquades. Menariknya, dalam penelitian ini ditemukan bahwa nilai koefisien difusi dari NaCl dengan Aquades kesesuaian yang cukup bagus dengan koefisien difusi yang tertera pada literatur. Karakterisasi alat telah dilakukan untuk mendapatkan metode pengukuran yang baik. Dengan susunan alat yang simpel, penggunaan yang baik, dan analisa data, sistem ini dapat digunakan untuk mengamati proses transfer massa antara dua cairan berbeda konsentrasi dengan cukup akurat.

Interdiffusion between two liquids with different concentration produce diverse refractive index gradient. A measurement system to observe this phenomena has been carefully constructed using laser beam deflection method. The laser beam deflection pattern come from refraction of the beam when entering the interface of two different refractive index liquid. Diffusion coefficient value can be determined by observing the refractive index gradient of liquid liquid on the interface. In this phenomenon, mass transfer which shown by diffusion coefficient value of liquid liquid take an important role and can be described using Fick rsquo s law. The diffusion experiment have been performed with NaCl Aqueous solution. Interistingly, we have found the diffusion coefficient of NaCl Aqueous has reasonably good agreement with coefficient values specified in literature. The system characterization has been done to get a good measurement method. With simple setup, good method, and data analysis, this system can be used to observe mass transfer between two liquids with different concentration accurately."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2017
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>