Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 154958 dokumen yang sesuai dengan query
cover
Anjanette Pinasthika Alexander
"Resin komposit Bulk-Fill merupakan material yang dapat merestorasi kavitas dengan kedalaman 4-5 mm dalam satu kali penyinaran. Polimerisasi resin komposit dipengaruhi oleh durasi penyinaran dan metode penyinaran Light Curing Unit. Polimerisasi adekuat diperlukan untuk mendapatkan kekerasan permukaan dan Depth of Cure yang optimal. Penelitian ini dilakukan untuk mengetahui kekerasan permukaan dan Depth of Cure resin komposit Bulk-Fill yang disinar menggunakan Light Curing Unit penyinaran pulsa selama 5, 10, dan 20 detik. Spesimen berjumlah 30 buah dibagi berdasarkan kelompok perlakuan yaitu kelompok durasi penyinaran (5, 10, dan 20 detik) dan penyinaran (pulsa dan kontinu). Spesimen berdiameter 6 mm dan tebal 4 mm diuji menggunakan Knoop Microhardness Tester dengan beban indentasi 50 g selama 10 detik pada 5 titik berbeda. Hasil penelitian menunjukkan peningkatan kekerasan permukaan yang disinar dengan Light Curing Unit penyinaran pulsa dan kontinu seiring pemanjangan durasi penyinaran. Terdapat perbedaan bermakna (p<0,05) pada kekerasan permukaan di kelompok durasi penyinaran. Pada nilai depth of cure dengan kedua Light Curing Unit tidak terdapat perbedaan bermakna (p>0,05). Sehingga disimpulkan, penyinaran pulsa Light Curing Unit selama 5, 10, dan 20 detik pada resin komposit Bulk-Fill mengalami peningkatan kekerasan permukaan yang signifikan dan penggunaan dua metode penyinaran sama baik pada nilai depth of cure.

Bulk-Fill composite resin have been introduced with the purpose of time savings. It can be placed in a 4-5 mm thickness bulks to be photo-cured in one step. Polymerization of composite resins affected by the irradiation time and mode. Adequate polymerization is needed to obtain optimal surface hardness and Depth of Cure. This study aimed to evaluate the influence of different exposure time with pulse-lighting mode on Bulk-Fill composite resin surface microhardness and Depth of Cure. Thirty specimens divided into 3 groups of exposure time (5, 10, and 20 sec) and 2 groups of irradiation mode (pulse and continuous), 6 mm in diameter and 4 mm in thick were prepared. Each specimen was measured using Knoop Microhardness Tester at each surface. The result showed that irradiation of Bulk-Fill composite resin with pulse-lighting mode curing unit for 5, 10, and 20 seconds experienced a significant increase in surface hardness. The depth of cure values shows no significant difference among different irradiation mode. It was concluded that that Bulk-Fill composite resin irradiated at longer exposure time exhibited significantly higher surface microhardness than those irradiated at shorter time. Meanwhile, there was no significant difference between two different irradiation mode for depth of cure."
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Jung, Jumin
"Latar belakang: Light Curing Unit (LCU) LED metode pulsa iradiansi 900 mW/cm2 telah dikembangkan untuk menghasilkan suhu pada ruang pulpa lebih rendah dibandingkan metode kontinu akibat polimerisasi resin komposit Nanofill pada durasi penyinaran 20 detik. Tujuan: menganalisis pengaruh durasi dan metode penyinaran pulsa terhadap kekerasan permukaan dan Depth of Cure resin komposit Nanofill. Metode: Spesimen resin komposit Nanofill (diameter 6 mm dan tebal 2 mm) disinar dengan LCU LED metode pulsa beriradiansi 900 mW/cm2 selama 5, 10, dan 20 detik, lalu direndam di dalam 5 ml akuades (37˚C 24 jam). Setiap spesimen diuji dengan Knoop Microhardness Tester sebanyak 5 kali pada permukaan atas dan bawah dan dihitung depth of cure. Hasil: Terjadi peningkatan kekerasan permukaan yang disinar dengan LCU metode penyinaran pulsa dan kontinu selama 5 hingga 20 detik yaitu 45,9±1,6/26,4±1,6 KHN hingga 68,8±1,8/57,4±1,6 KHN, dan 46,8±1,6/28,2±1,5 KHN hingga 69,3±1,2/57,8±1,1 KHN. Terdapat perbedaan bermakna (p<0,05) pada kekerasan permukaan di kelompok durasi penyinaran dengan uji One-way Anova dan post hoc Tamhane. Pada nilai depth of cure resin komposit Nanofill yang disinar antara kedua metode penyinaran tidak terdapat perbedaan bermakna (p>0,05) secara statistik. Kesimpulan: Resin komposit Nanofill yang disinar pada durasi lebih lama menunjukkan kekerasaan permukaan atas maupun bawah lebih tinggi dibandingkan dengan durasi lebih pendek. Demikian pula, depth of cure pada durasi lebih lama menunjukkan nilai lebih tinggi. Penyinaran metode pulsa iradiansi 900 mW/cm2 dan kontinu iradiansi 900 mW/cm2 menunjukkan kekerasan permukaan dan depth of cure yang sama."
Depok: Fakultas Kedokteran Gigi Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Alamsyah Putra
"Latar belakang : Resin komposit bulkfill merupakan resin terbaru yang dapat direstorasi dengan kedalaman 4-5 mm dalam sekali penyinaran. Polimerisasi dipengaruhi oleh durasi penyinaran dan besaran irradiansi lightcuring untuk mendapatkan kekerasan permukaan dan depth of cure yang optimal. Tujuan: Penelitian ini bertujuan untuk mengetahui perbedaan nilai kekerasan resin komposit dan depth of cure resin komposit Tetric® N- Ceram bulk-fill yang disinari lightcure dengan durasi 5 detik, 10 detik dan 15 detik. Metode Penelitian: Dalam penelitian ini digunakan 24 spesimen resin komposit Tetric® N-Ceram bulk-fill berbentuk silinder dengan ukuran diameter 6 mm dan tebal 4 mm. Selembar mylar strip diletakkan diatas permukaan resin komposit sebelum dilakukan proses curing. Polimerisasi dilakukan menggunakan Light Curing Unit (LED DBA iLed) selama 5 detik, 10 detik dan 15 detik dengan irradiansi 1100 mW/cm2. Setelah polimerisasi, spesimen direndam dalam akuades pada suhu 37oC selama 24 jam. Spesimen dibagi menjadi tiga kelompok (n=8) yaitu; kelompok resin komposit dengan penyinaran 5 detik, penyinaran 10 detik dan penyinaran 15 detik. Spesimen diuji menggunakan HMV-G Series Micro Vickers Hardness Tester (Shimadzu, Jepang) dengan beban 100 gram selama 10 detik untuk mendapatkan nilai kekerasan. Data dianalisis dengan uji statistik Kruskall Wallis dan Post-Hoc Mann Whitney. Hasil Penelitian: Hasil uji statistik menunjukkan kenaikan bermakna nilai kekerasan permukaan dan depth of cure pada resin komposit Tetric® N-Ceram bulk-fill. Nilai kekerasan dan depth of cure tertinggi terlihat pada resin komposit Tetric® N-Ceram bulk-fill pada kelompok penyinaran 15 detik, yaitu sebesar 41,61 ± 1,25 KHN dan 72,71 ± 1,88. Kesimpulan: Disimpulkan bahwa semakin bertambah durasi penyinaran lightcure yang disinari, semakin bertambah nilai kekerasan permukaan dan depth of cure resin komposit Tetric® N-Ceram bulk-fill.

Background : Bulkfill composite resin is the newest resin that can be restored to a depth of 4-5 mm in one step. Polymerization is determined by the irradiation time and the amount of light curing irradiance to obtain optimal microhardness and depth of cure. Objective: The aim of this study was to determine the difference in the value of the microhardness of the composite resin and the depth of cure of the Tetric® N-Ceram bulk- fill composite resin irradiated by lightcure with a duration of 5 seconds, 10 seconds and 15 seconds. Method: Twenty four specimens of Tetric® N-Ceram bulk-fill Composite Resin were used in this study. All materials were prepared into disk-shaped specimens of 6 mm in diameter and 4 mm in thickness. A piece of mylar strip was placed on the top of the specimens just before the polymerization.. Polymerization was carried out using a Light Curing Unit (LED DBA iLed) for 5 seconds, 10 seconds and 15 seconds with an irradiance of 1100 mW/cm2. After polymerization, specimens were immersed in 37 aquadest solution for 24 hours. Specimens were divided into three groups (n=8) that is; composite resin group with 5 seconds of irradiation, 10 seconds of irradiation and 15 seconds of irradiation. Specimens were tested with HMV-G Series Micro Vickers Hardness Tester (Shimadzu, Jepang) with 100 gram indentation in 10 seconds. Data were analyzed using Kruskall Wallis and Post-Hoc Mann Whitney to assess the significant differences among groups Result: The results of statistical tests showed a significant increase in the value of microharhardness and depth of cure on Tetric® N-Ceram bulk- fill composite resin. The highest microhardness and depth of cure values were seen in the Tetric® N-Ceram bulk-fill composite resin in the 15 second irradiation group, namely 41.61 ± 1.25 KHN and 72.71 ± 1.88. Conclusion: It was concluded that the longer the duration of irradiation of the irradiated lightcure, the higher the microhardness value and depth of cure of the Tetric® N-Ceram bulk-fill composite resin."
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Dessy Innawaty
"Penelitian ini bertujuan untuk mengevaluasi pengaruh durasi penyinaran menggunakan LED dan pemanasan awal menggunakan Micerium ENA Heat terhadap depth of cure resin komposit bulk-fill. Alat dan bahan: Enam puluh spesimen Filtek Bulk-Fill Posterior Restoratives ketebalan 4 mm dan diameter 3 mm; tanpa dan dengan pemanasan awal pada temperatur 39 C dibagi ke dalam 3 kelompok sesuai dengan durasi penyinaran 5 detik, 10 detik, dan 15 detik. Spesimen dipolimerisasi menggunakan LED Curing Unit 3MTM Elipar, 1.200 mW/cm2 dan diuji kekerasan mikro menggunakan Vickers Microhardness Tester Shimadzu, Japan untuk menghitung nilai depth of cure. Data yang diperoleh dianalisis menggunakan uji statistik Kruskall-Wallis dan Post-Hoc Mann Whitney-U.
Hasil: Adanya perbedaan yang tidak bermakna p ge;0,05 untuk nilai depth of cure pada keenam kelompok tanpa dan dengan pemanasan awal. Walaupun nilai depth of cure tersebut tidak bermakna namun telah mencapai nilai minimum yaitu ge; 80. Selain itu terdapat perbedaan yang bermakna p.

Aim Evaluate the influence of different exposure time and pre heating on its depth of cure of bulk fill composite. Methods Sixty cylinder shaped specimens of Filtek Bulk Fill Posterior Restoratives 4 mm of thickness x 3 mm of diameter with and without pre heating at 39 C were divided into 3 subgroups according to exposure times 5, 10, and 15. All specimens were polymerized using LED Curing Unit 3MTM Elipar, 1.200 mW cm2 and tested using Vickers Microhardness Tester Shimadzu, Japan to determine its microhardness for calculating its depth of cure. Data were statistically analyzed using Kruskall Wallis and Post Hoc Mann Whitney U test.
Results A no significant differences p ge 0,05 in depth of cure amongst the six groups of non preheated and preheated bulk fill composite. However, all of the groups have reached a minimum value of ge 80 depth of cure. Moreover, there is a significant differences in microhardness in all of the six groups of non preheated and preheated bulk fill composite and between 5 and 15 of exposure times in both groups. Conclusion Exposure times and pre heating at 39 C had an influence on microhardness of bulk fill composite.
"
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2017
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Mesy
"Latar belakang: Resin komposit Bulk-fill merupakan material tumpatan gigi yang dapat digunakan pada kavitas gigi posterior sedalam 4-5mm dengan satu kali penyinaran. Durasi penyinaran dan metode penyinaran mempengaruhi derajat polimerisasi dari suatu material tumpatan gigi. Sehingga derajat polimerisasi akan mempengaruhi sifat mekanik salah satunya adalah kuat tarik diametral suatu material resin komposit Bulk-fill. Tujuan: Untuk mengetahui kuat tarik diametral resin komposit Bulk-fill yang disinar menggunakan Light Curing Unit eksperimental metode penyinaran pulsa dan Light Curing Unit komersial metode penyinaran kontinu selama 5 detik, 10 detik dan 20 detik. Metode: Enam puluh spesimen resin komposit Bulk-fill (diameter 6mm dan ketebalan 3mm) yang dibagi menjadi 2 kelompok metode penyinaran (pulsa dan kontinu) dan 3 kelompok durasi penyinaran (5 detik, 10 detik, 20 detik) dan direndam didalam 5ml akuades kemudian disimpan dalam inkubator 37oC selama 24 jam. Spesimen lalu dilakukan uji kuat tarik diametral menggunakan Universal Testing Machine dengan beban uji sebesar 250kgFdengan crosshead speed 0,5 mm/menit Hasil: Terdapat peningkatan nilai kuat tarik diametral selama 5 detik, 10 detik dan 20 detik pada metode penyinaran pulsa (53,90±8,53 MPa, 54,94±7,68 MPa, 56,18±6,99 MPa) dan metode penyinaran kontinu (53,26±5,78 MPa, 56,40±5,15 MPa, 57,17±5,70 MPa). Uji One-Way ANOVA menunjukkan tidak terdapat perbedaan yang bermakna (p>0,05) antara durasi penyinaran dan juga metode penyinaran. Kesimpulan: Kuat tarik diametral pada metode penyinaran pulsa memiliki nilai yang lebih rendah dibandingkan dengan metode penyinaran kontinu.

in posterior tooth cavities as deep as 4-5mm with one curing. The duration and method of curing affect the degree of polymerization of a tooth filling material. Therefore, the degree of polymerization will affect the mechanical properties, one of which is the diametral tensile strength of a Bulk-fill composite resin material. Objective: To determine the diametral tensile strength of Bulk-fill composite resins cured using the experimental Light Curing Unit pulses curing method and commercial Light Curing Units with continuous curing method for 5 seconds, 10 seconds and 20 seconds. Method: Sixty Bulk-fill composite resin specimens (6mm diameter and 3mm thickness) were divided into 2 groups of curing methods (pulses and continuous) and 3 groups of curing duration (5 seconds, 10 seconds, 20 seconds) then immersed in 5 ml distilled water and stored in 37oC incubator for 24 hours. Specimens were then tested with diametral tensile strength using a Universal Testing Machine with a test load of 5 kN with a crosshead speed of 0.5 mm/minute. Result: There was an increase in diametral tensile strength values for 5 seconds, 10 seconds, and 20 seconds in the pulse curing method (53.90 ± 8.53 MPa, 54.94 ± 7.68 MPa, 56.18 ± 6.99 MPa) and also an increase in the continuous curing method (53.26 ± 5.78 MPa, 56.40 ± 5.15 MPa, 57.17 ± 5.70 MPa). One-Way ANOVA test showed no significant difference (p> 0.05) between each duration and method of curing. Conclusion: The diametral tensile strength of the pulse curing method has a lower value compared to the continuous irradiation method."
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Putri Risky Auliana
"Latar Belakang : Pada penelitian sebelumnya, iradiasi menggunakan iradiasi pulsa LCU cenderung diikuti dengan suhu cahaya yang relatif rendah sehingga aman untuk pulpa gigi dan telah diaplikasikan untuk polimerisasi resin komposit nanofil dalam waktu 20 detik. berdenyut melawan kekuatan kompresi selama 5, 10, 20 detik. Metode : 60 spesimen resin komposit isi curah silinder diameter 3 mm dan tebal 6 mm, diiradiasi dengan LCU eksperimental iradiasi pulsa dan LCU komersial iradiasi kontinyu sebagai kontrol selama 5, 10, 20 detik. Kemudian direndam dengan air suling selama 24 jam. Spesimen kemudian diuji kuat tekannya menggunakan mesin uji universal (Shimadzu AGS-X 5kN, Jepang) dengan kecepatan crosshead 0,5m/s. Hasil: terjadi peningkatan kuat tekan resin komposit isian curah iradiasi
dengan LCU eksperimental selama 5, 10, 20 detik, memiliki hasil berturut-turut sekitar 209,43 hingga 241,80 MPa. Kemudian dengan iradiasi kontinyu LCU komersial memiliki hasil berturut-turut sekitar 210,69 hingga 261,72 MPa. Analisis one-way ANOVA dan post hoc bonferroni menunjukkan hasil yang tidak berbeda nyata (p>0,05) nilai kuat tekan antara kedua metode penyinaran pada lama waktu yang sama. Tidak terdapat perbedaan yang signifikan pada masing-masing metode iradiasi pada durasi yang berbeda. Sementara itu, mendeteksi perbedaan yang signifikan (p<0,05) pada kekuatan tekan resin komposit pengisian curah dengan penyinaran antara 5 dan 10 detik dan 5 dan 20 detik dengan metode penyinaran kontinu. Kesimpulan: kuat tekan resin komposit bulk fill baik dengan iradiasi pulsa maupun kontinyu selama 5, 10, 20 detik meningkat dengan bertambahnya lama iradiasi, dan iradiasi menggunakan metode pulsa dan
kuat tekan kontinyu menghasilkan resin komposit bulk fill yang tidak berbeda nyata.
Background : In previous studies, irradiation using LCU pulse irradiation tends to be followed by a relatively low light temperature so that it is safe for dental pulp and has been applied to polymerize nanofil composite resins within 20 seconds. pulse against the force of compression for 5, 10, 20 seconds. Methods : 60 specimens of cylindrical bulk-filled composite resin with a diameter of 3 mm and a thickness of 6 mm, were irradiated with pulse irradiation experimental LCU and continuous irradiated commercial LCU as control for 5, 10, 20 seconds. Then soaked with distilled water for 24 hours. The specimens were then tested for compressive strength using a universal testing machine (Shimadzu AGS-X 5kN, Japan) with a crosshead speed of 0.5m/s. Result: there was an increase in the compressive strength of the irradiated bulk filled composite resin with the experimental LCU for 5, 10, 20 s, had successive yields of about 209.43 to 241.80 MPa. Then with continuous irradiation commercial LCU has successive yields of about 210.69 to 261.72 MPa. One-way ANOVA and post hoc bonferroni analysis showed that the results were not significantly different (p>0.05) in the compressive strength between the two irradiation methods at the same time. There was no significant difference in each irradiation method at different durations. Meanwhile, detecting a significant difference (p<0.05) in the compressive strength of composite resin bulk filling with irradiation between 5 and 10 seconds and 5 and 20 seconds with the continuous irradiation method. Conclusion: the compressive strength of bulk fill composite resins both with pulse and continuous irradiation for 5, 10, 20 seconds increased with increasing irradiation time, and irradiation using pulse and pulse irradiation methods continuous compressive strength resulted in bulk fill composite resin which was not significantly different."
Depok: Fakultas Kedokteran Gigi Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rifdah Yunerizka Fatma
"Latar belakang: Mode penyinaran pulsa merupakan alternatif dari mode penyinaran kontinu untuk mempolimerisasi resin komposit. Saat ini resin komposit nanofil dan bulkfil merupakan material restorasi yang memerlukan surface gloss yang baik untuk memenuhi kebutuhan estetik. Surface gloss dapat dipengaruhi oleh penyinaran.
Tujuan: Untuk menganalisa pengaruh penyinaran mode kontinu dan pulsa terhadap surface gloss resin komposit nanofil dan bulkfil segera dan setelah satu hari.
Metode: Spesimen resin komposit nanofil dan bulkfil disinar menggunakan mode kontinu atau pulsa beriradiansi 900 mW/cm2 selama 20 detik. Lalu dilakukan pengujian surface gloss segera setelah penyinaran. Kemudian spesimen disimpan selama satu hari dan dilakukan pengujian surface gloss kembali.
Hasil: Surface gloss yang dihasilkan oleh mode penyinaran kontinu dan pulsa tidak bermakna secara statistik (p>0,05). Resin komposit nanofil menghasilkan surface gloss lebih rendah daripada bulkfil, berbeda bermakna (p=0,00). Segera setelah penyinaran menghasilkan surface gloss lebih tinggi daripada setelah satu hari tidak bermakna secara statistik (p>0,05).
Kesimpulan: Pada penelitian ini surface gloss tidak dipengaruhi oleh mode penyinaran kontinu dan pulsa serta perbedaan waktu segera dan setelah satu hari. Namun terdapat pengaruh jenis resin komposit, nanofil menghasilkan surface gloss lebih rendah dari yang dihasilkan bulkfil.

Background: Pulse is an alternative of continuous light-curing mode to polymerize composite resin. Currently, nanofill and bulk-fill are restorative materials that require good gloss surface to meet aesthetic needs. Surface gloss can be obtained by irradiation.
Aim: To analyze influence of continuous and pulse light-curing mode on surface gloss of nanofill and bulk-fill immediately after irradiation and after one day.
Method: Nanofill and bulk-fill specimens were irradiated using continuous or pulse light-curing mode with irradiance of 900 mW/cm2 for 20 seconds. Then surface gloss test is carried out immediately after irradiation. Then the specimens were water-stored for one day and then tested their surface gloss again.
Result: Surface gloss produced by continuous and pulse light-curing mode were not statistically different (p>0,05). Nanofill produced lower surface gloss than bulk-fill, statistically significant (p=0,00). Immediately after irradiation, resulting surface gloss were higher than after one day, not statistically significant (p>0,05).
Conclusion: In this experiment, surface gloss was not affected by continuous and pulse light-curing mode as well as the time difference immediately and after one day. However, there is an influence on the type of composite resin, where nanofill produced lower surface gloss than bulk-fill.
"
Depok: Fakultas Kedokteran Gigi Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Trihanna Kezya Rima
"Penelitian ini bertujuan untuk mengetahui pengaruh perendaman minuman isotonik terhadap kekerasan permukaan resin komposit bulk-fill. Enam puluh spesimen Tetric N-Ceram Bulk-Fill berdiameter 6 mm dan tinggi 3 mm dibagi menjadi 2 kelompok perendaman yaitu dengan akuades (kontrol) dan minuman isotonik. Setiap kelompok direndam dengan lama perendaman 1 hari, 3 hari dan 7 hari. Kekerasan permukaan diuji menggunakan HMV-G Series Micro Vickers Hardness Tester.
Hasil menunjukan terdapat perbedaan bermakna (p<0,05) antara perendaman akuades dan minuman isotonik uji Independent T-Test. Hasil menunjukkan bahwa terdapat perbedaan bermakna (p<0,05) antara semua kelompok perendaman minuman isotonik dengan lama perendaman 1 hari, 3 hari dan 7 hari dengan uji statistik One-Way Anova dan PostHoc Tukey HSD. Dapat disimpulkan bahwa minuman isotonik mempengaruhi kekerasan permukaan resin komposit bulk-fill.

This study aims to determine the influence of isotonic drink immersion on surface hardness of bulk-fill composite. Sixty specimens of Tetric N-Ceram Bulk-Fill, 6 mm in diameter and 3 mm height were divided into two groups of storage media; deionized water (control) and isotonic drink. Each group was for 1 day, 3 days and 7 days. The surface hardness is measured using a HMV-G Series Micro Vickers Hardness Tester.
The results showed that there were significant differences (p <0.05) between immersion of control and isotonic drink with Independet T-Test. The results showed that there were significant differences (p <0.05) between all isotonic drink immersion groups with immersion duration of 1 day, 3 days and 7 days with One-Way Anova Test and Post Hoc Tukey HSD. It can be concluded that isotonic drinks affect the surface hardness of bulk-fill composite.
"
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Athaya Putri Indrani
"Latar Belakang: Material restorasi yang paling berkembang pesat sampai saat ini adalah resin komposit. Resin komposit yang beredar di pasaran dan menurun klaim pabrik memiliki sifat estetika yang baik, mudah dimanipulasi, serta dapat dipakai secara universal adalah Resin Komposit Supra-Nano Palfique Universal Flow. Suatu material restorasi harus mengalami polimerisasi yang adekuat agar menghasilkan sifat fisik, kimia, mekanik, dan biologis yang optimal. Sifat kekerasan mikro dan depth of cure material dapat menjadi indikator seberapa baik polimerisasi suatu material. Pada keadaan klinis, anatomi gigi dapat menghalangi sinar untuk berada tepat di atas permukaan restorasi sehingga jarak dan durasi penyinaran memengaruhi kekerasan mikro dan depth of cure resin komposit. Tujuan: Menganalisis pengaruh jarak dan durasi penyinaran terhadap kekerasan mikro dan depth of cure Resin Komposit Supra-Nano Palfique Universal Flow. Metode: Tiga puluh spesimen Resin Komposit Supra-Nano Palfique Universal Flow berbentuk silinder berdiameter 6 mm dan tinggi 2 mm dipersiapkan untuk penelitian ini. Spesimen terbagi menjadi 6 kelompok berdasarkan jarak penyinaran (0,3, dan 6 mm) dan durasi penyinaran (10 dan 15 detik) yang disinari light curing unit dengan iradiansi 1050 mW/cm2. Uji kekerasan dilakukan pada permukaan atas spesimen, dan diuji juga kekerasan pada permukaan bawah spesimen untuk menghitung depth of cure (DoC). DoC dihitung dengan menggunakan metode bottom/top hardness ratio (%). Data dianalisis menggunakan uji statistik One-way ANOVA dan Independent Sample T-test. Hasil: Kekerasan mikro dan DoC semakin tinggi pada jarak yang semakin dekat baik pada durasi 10 maupun 15 detik. Nilai kekerasan mikro dan DoC pada durasi penyinaran 15 detik lebih tinggi dibandingkan durasi penyinaran 10 detik pada jarak yang sama secara signifikan (p<0.05). DoC > 80% hanya didapatkan pada kelompok dengan jarak penyinaran 0 mm dengan durasi penyinaran 10 dan 15 detik yaitu 81,44 ± 0,02% dan 92,64 ± 0,01% secara berurutan, serta pada kelompok dengan jarak penyinaran 3 mm dan durasi penyinaran 15 detik, yaitu 88,78 ± 0,02%. Kesimpulan: Semakin dekat jarak penyinaran dan semakin lama durasi penyinaran, maka kekerasan mikro dan DoC akan semakin tinggi.

Background: The most rapidly developing restoration material to date is composite resin. The composite resin on the market and according to manufacturer claims has good aesthetic properties, is easy to manipulate and can be used universally is Palfique Universal Flow Supra-Nano Composite Resin. A material restoration must have an adequate polymerization to produce optimal physical, chemical, mechanical, and biological properties. The microhardness and depth of cure properties of a material can be an indicators of how well a material is polymerized. In clinical situations, anatomical teeth can prevent light from being directly above the surface of the restoration so that the distance and duration of light-curing affect the microhardness and depth of cure of the composite resin. Objective: To analyze the effect of light-curing distance and duration on the microhardness and depth of cure of Supra-Nano Palfique Universal Flow Composite Resin. Methods: Thirty specimens of Palfique Universal Flow Supra-Nano Composite Resin in a cylindrical shape with a diameter of 6 mm and a height of 2 mm were prepared for this study. Specimens were divided into 6 groups based on the light-curing distance (0,3, and 6 mm) and duration (10 and 15 seconds) which were exposed to a light curing unit with an irradiance of 1050 mW/cm2. The hardness test was on the top surface of the specimen, and hardness was also tested on the bottom surface of the specimen to calculate the depth of cure (DoC). DoC was calculated using the bottom/top hardness ratio (%) method. Data was analyzed statistically by One-way ANOVA and Independent Sample T-test. Results: Microhardness and DoC were higher at closer light-curing distances for both 10 and 15 seconds. Microhardness and DoC values at a light-curing duration of 15 seconds were significantly higher than at a duration of 10 seconds at the same distance (p<0.05). DoC > 80% was only obtained in the group with a light-curing distance of 0 mm with a duration of 10 and 15 seconds, that is 81.44 ± 0.02% and 92.64 ± 0.01% respectively, and 88.78 ± 0.02% in the group with a light-curing distance of 3 mm and a duration of 15 seconds. Conclusion: The closer the light-curing distance and the longer the light-curing duration, the higher the microhardness and DoC."
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Athaya Putri Indrani
"Latar Belakang: Material restorasi yang paling berkembang pesat sampai saat ini adalah resin komposit. Resin komposit yang beredar di pasaran dan menurun klaim pabrik memiliki sifat estetika yang baik, mudah dimanipulasi, serta dapat dipakai secara universal adalah Resin Komposit Supra-Nano Palfique Universal Flow. Suatu material restorasi harus mengalami polimerisasi yang adekuat agar menghasilkan sifat fisik, kimia, mekanik, dan biologis yang optimal. Sifat kekerasan mikro dan depth of cure material dapat menjadi indikator seberapa baik polimerisasi suatu material. Pada keadaan klinis, anatomi gigi dapat menghalangi sinar untuk berada tepat di atas permukaan restorasi sehingga jarak dan durasi penyinaran memengaruhi kekerasan mikro dan depth of cure resin komposit. Tujuan: Menganalisis pengaruh jarak dan durasi penyinaran terhadap kekerasan mikro dan depth of cure Resin Komposit Supra-Nano Palfique Universal Flow. Metode: Tiga puluh spesimen Resin Komposit Supra-Nano Palfique Universal Flow berbentuk silinder berdiameter 6 mm dan tinggi 2 mm dipersiapkan untuk penelitian ini. Spesimen terbagi menjadi 6 kelompok berdasarkan jarak penyinaran (0,3, dan 6 mm) dan durasi penyinaran (10 dan 15 detik) yang disinari light curing unit dengan iradiansi 1050 mW/cm2. Uji kekerasan dilakukan pada permukaan atas spesimen, dan diuji juga kekerasan pada permukaan bawah spesimen untuk menghitung depth of cure (DoC). DoC dihitung dengan menggunakan metode bottom/top hardness ratio (%). Data dianalisis menggunakan uji statistik One-way ANOVA dan Independent Sample T-test. Hasil: Kekerasan mikro dan DoC semakin tinggi pada jarak yang semakin dekat baik pada durasi 10 maupun 15 detik. Nilai kekerasan mikro dan DoC pada durasi penyinaran 15 detik lebih tinggi dibandingkan durasi penyinaran 10 detik pada jarak yang sama secara signifikan (p<0.05). DoC > 80% hanya didapatkan pada kelompok dengan jarak penyinaran 0 mm dengan durasi penyinaran 10 dan 15 detik yaitu 81,44 ± 0,02% dan 92,64 ± 0,01% secara berurutan, serta pada kelompok dengan jarak penyinaran 3 mm dan durasi penyinaran 15 detik, yaitu 88,78 ± 0,02%. Kesimpulan: Semakin dekat jarak penyinaran dan semakin lama durasi penyinaran, maka kekerasan mikro dan DoC akan semakin tinggi.

Background: The most rapidly developing restoration material to date is composite resin. The composite resin on the market and according to manufacturer claims has good aesthetic properties, is easy to manipulate and can be used universally is Palfique Universal Flow Supra-Nano Composite Resin. A material restoration must have an adequate polymerization to produce optimal physical, chemical, mechanical, and biological properties. The microhardness and depth of cure properties of a material can be an indicators of how well a material is polymerized. In clinical situations, anatomical teeth can prevent light from being directly above the surface of the restoration so that the distance and duration of light-curing affect the microhardness and depth of cure of the composite resin. Objective: To analyze the effect of light-curing distance and duration on the microhardness and depth of cure of Supra-Nano Palfique Universal Flow Composite Resin. Methods: Thirty specimens of Palfique Universal Flow Supra-Nano Composite Resin in a cylindrical shape with a diameter of 6 mm and a height of 2 mm were prepared for this study. Specimens were divided into 6 groups based on the light-curing distance (0,3, and 6 mm) and duration (10 and 15 seconds) which were exposed to a light curing unit with an irradiance of 1050 mW/cm2. The hardness test was on the top surface of the specimen, and hardness was also tested on the bottom surface of the specimen to calculate the depth of cure (DoC). DoC was calculated using the bottom/top hardness ratio (%) method. Data was analyzed statistically by One-way ANOVA and Independent Sample T-test. Results: Microhardness and DoC were higher at closer light-curing distances for both 10 and 15 seconds. Microhardness and DoC values at a light-curing duration of 15 seconds were significantly higher than at a duration of 10 seconds at the same distance (p<0.05). DoC > 80% was only obtained in the group with a light-curing distance of 0 mm with a duration of 10 and 15 seconds, that is 81.44 ± 0.02% and 92.64 ± 0.01% respectively, and 88.78 ± 0.02% in the group with a light-curing distance of 3 mm and a duration of 15 seconds. Conclusion: The closer the light-curing distance and the longer the light-curing duration, the higher the microhardness and DoC."
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>