Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 148073 dokumen yang sesuai dengan query
cover
Muhammad Muwatha Malik
"Hot Mix Asphalt HMA dan Warm Mix Asphalt WMA merupakan beberapa dari metode campuran aspal pada perkerasan lentur. Zeolit merupakan salah satu bahan aditif yang berkontribusi dalam metode WMA agar bisa dilaksanakan. Penggunaan Buton Natural Asphalt Rubber BNA-R sebagai bahan tambah yang dapat memberikan kontribusi dalam meningkatkan kekuatan campuran aspal.
Penelitian ini dilakukan untuk mengetahui kontribusi BNA-R pada campuran panas dan hangat, kemudian untuk mengetahui perubahan karakteristik tersebut akibat bahan aditif zeolit dalam campuran aspal hangat dengan menggunakan spesifikasi AC-BC. Prosedur pengujian yang dilakukan adalah uji karakteristik aspal dan aspal modifikasi, uji Marshall, dan uji Marshall Immersion dimana pada penelitian ini hasil tersebut akan dibandingkan.
Hasil dari penelitian ini mengindikasi bahwa penggunaan aspal modifikasi BNA-R pada spesifikasi AC-BC kurang baik dimana karakteristiknya berada dibawah aspal pen 60/70 tetapi pada Indeks Kekuatan Sisa IKS sebesar 89.516 pada kadar BNA-R 5 . Indikasi yang berbeda didapat pada campuran hangat dimana nilai stabilitas tertinggi didapat pada kadar BNA-R 7,5 pada suhu campuran 1400C dengan nilai stabilitas 1140,46 kg.

Hot Mix Asphalt HMA and Warm Mix Asphalt WMA are some of the asphalt mixture methods on flexible pavements. Zeolite is one of the additive materials that contribute in WMA method to be implemented. Use of Buton Natural Asphalt Rubber BNA R as an added ingredient that can contribute in improving the strength of the asphalt mixture.
This research was conducted to know the contribution of BNA R on hot and warm mixture, then to know the characteristic change caused by zeolite additive in hot asphalt mixture by using AC BC specification. The test procedure performed is the asphalt and bitumen modification test, Marshall test, and Marshall Immersion test which in this study the results will be compared.
The results of this study indicate that the use of BNA R modified asphalt on the AC BC specification is poor where its characteristics are below the asphalt pen 60 70 but in the Remaining Strength Index of 89.516 at BNA R 5. Different indications are obtained in warm mixtures where the highest stability values are obtained at 7.5 BNA R at a mixed temperature of 1400C with a stability value of 1140.46 kg.
"
Depok: Fakultas Teknik Universitas Indonesia, 2017
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Natasha Anagi
"Bahan aditif BNA-R dan Zeolit dapat mempengaruhi kekesatan permukaan pada campuran aspal hangat, terutama pada bagian permukaan aspal sebelum terlintasi dan sesudah terlintasi sebanyak 7560 lintasan dengan menggunakan Wheel Tracking Machine. Pengujian skid pada penelitian ini menggunakan alat British Pendulum Tester yang telah dimodifikasi agar dapat dilakukan pengujian dengan temperatur yang diinginkan.
Hasil penelitian menunjukkan bahwa BNA-R dapat meningkatkan nilai skid pada awalnya, namun BNA-R tidak dapat mempertahankan kenaikan nilai skid tersebut setelah campuran aspal dilintasi sebanyak 7560 lintasan. Untuk bahan tambah zeolit terbukti bahwa aditif tersebut dapat meningkatkan nilai skid dan menaikkan ketahanan aspal terhadap temperatur.

BNA R and zeolite additives can affects the skid resistance of warm mix asphalt, especially on the surface of the asphalt before it passes through and after 7560 as many passes through the track by using the Wheel Tracking Machine. This study used a British Pendulum Tester, which has been modified in order to be tested with the desired temperature.
The results showed that the BNA R can increase the value of skid at first but BNA R can not sustain the increase in the value of the skid after the asphalt is crossed by as much as 7560 tracks. For added zeolite material is proven that such additives can increase the value and increase skid resistance versus asphalt temperature.
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
S68142
UI - Skripsi Membership  Universitas Indonesia Library
cover
Eggi Luftiawan
"Kerusakan jalan dapat diawali oleh adanya keretakan pada lapis permukaan. Pengaruh dari alur roda kendaraan menjadi salah satu penyebab keretakan atau deformasi alur roda kendaraan. Dengan menggunakan bahan additive pada campuran aspal beton sebagai salah satu yang dapat mengurangi kerusakan jalan tersebut.
Penelitian ini membahas pengaruh deformasi pada campuran aspal dengan penambahan Buton Natural Aspal terhadap aspal pen 60/70 untuk campuran laston AC-WC. Penambahan additive sebesar 20%dan 30% telah dilakukan. Benda uji untuk pengujian marshall standar, marshall immersion dan uji deformasi dengan Wheel Tracking Machine pada kadar aspal optimum 5.5%.
Beberapa pengujian untuk mengetahui pengaruh temperature telah digunakan suhu 30°C dan 60°C dan jumlah 1260 lintasan tiap benda uji. Berdasarkan hasil pengujian tersebut dapat disimpulkan bahwa penggunaan bahan additive BNA telah menunjukkan adanya ketahanan campuran aspal beton akibat temperature.

Road damage can be initiated by the presence of cracks in the surface layer. Influence of groove wheel vehicle to be one cause cracking or deformation of grooves wheel vehicle. By using additive materials in asphalt concrete mix as one that can reduce the damage to the road.
This study discusses the effect of deformation on he asphalt mixture with theaddition of Buton Natural Asphalt to asphalt mix laston pen 60/70for AC-WC. The addition of the additive by 20% and 30% have done. Specimens for testing standar marshall, marshall immersion and deformation test with Wheel Tracking Machine at optimum bitumen content 5.5%.
Some testing to determine the effect of temperature has been used a temperature of 30°C and 60°C and the number of 1260 trajectories for each test specimen. Based on the test results, we can conclude that the use of additive materials BNA have shown resilience mix asphalt concrete due to temperature.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
S53867
UI - Skripsi Membership  Universitas Indonesia Library
cover
Puspita Jayanthi
"Kekesatan permukaan jalan merupakan kondisi tahanan gesek antara permukaan jalan dan ban kendaraan sehingga tidak mengalami selip atau tergelincir baik pada kondisi basah waktu hujan ataupun kering. Kekesatan permukaan jalan bergantung pada jenis tekstur permukaan, apabila tekstur yang kasar akan memberikan kekuatan yang lebih dibandingkan dengan permukaan yang licin.
Pada penelitian ini dilakukan pengukuran dan analisis tingkat kekesatan permukaan perkerasan dengan alat British Pendulum Tester pada sampel campuran Asphalt Concrete ? Wearing Course dan pada sampel yang telah terjadi akibat perubahan alur karena terlintas oleh mesin Wheel Tracking sebagai simulasi roda kendaraan di lapangan. Dimana campuran Asphalt Concrete ? Wearing Course yang telah dicampur limbah serat serabut kelapa dengan kadar komposisi 0% ; 0,75% dan 1,5% terhadap aspal modifikasi. Pengujian dilakukan dengan variasi suhu 26°C, 30°C, 35°C, 40°C, 45°C, 50°C dalam keadaan kondisi basah.
Dengan penambahan serat serabut 0,75% pada aspal modifikasi ini, menghasilkan nilai kekesatan permukaan yang lebih tinggi sehingga menambah kestabilan jalan dan memiliki kemampuan tahanan yang tinggi terhadap perubahan suhu pada permukaan aspal dimana yang bersentuhan langsung dengan roda pada kendaraan.

Skid resistance is the frictional condition resistance between road surface and vehicle tires that are not encountering either slip when wet conditions or dry conditions. Skid resistance depends on the type of surface texture if the rough texture will provide more power than the slip surface.
This research is done measurement and analysis of skid resistance number with British Pendulum Tester for mix specimen of Asphalt Concrete ? Wearing Course and specimen has happened due to changes of flow because passed by Wheel Tracking machine as simulation of vehicle wheels on the ground. Which mixture Asphalt Concrete ? Wearing Course has mixed fiber of coconut with content 0% ; 0,75% and 1,5% to asphalt modification. Testing is done with temperature variations 26°C, 30°C, 35°C, 40°C, 45°C, 50°C on wet conditions.
The addition fiber of coconut 0,75% on this asphalt modification will result higher values skid resistance due add the stability of road and have the ability of high resistance to temperature changes on the surface of the asphalt which in direct contact with the wheels on the vehicle."
Depok: Fakultas Teknik Universitas Indonesia, 2013
S53417
UI - Skripsi Membership  Universitas Indonesia Library
cover
Iqbal Gita Bhaskara
"Dalam mendesain jalan raya perlu memperhatikan faktor pelayanannya, salah satunya adalah faktor keselamatan jalan dilihat dari kekesatannya. Kekesatan suatu jalan raya dapat diketahui dengan menggunakan alat British Pendulum Tester(BPT) yang mana akan dapat dilihat dari nilai Skid Numbernya. Penggunaan aspal modifikasi digunakan untuk merubah nilai viskositas pada campuran aspal panas dan hangat. Penelitian bertujuan untuk mengetahui pengaruh viskositas pada campuran aspal ACWC. Aditif yang digunakan berupa BNA-R pada campuran hangat dan Tire Rubber Powder pada campuran panas, yang menyebabkan nilai viskositas yang semakin tinggi tiap kadarnya sehingga akan menaikan skid number yang ada.

In Pavement design we must consider every major and minor factors to create safetiness in using highways. One of them is skid resistance which measure the roughness in pavements. Using British Pendulum Tester we can measure the skid number from road pavements. Modified Asphalts helps to influence the viscosity number in hot and warm mix asphalt. The study aims to determine the influence of viscosity according to Asphalt Concrete Wearing Course (AC-WC). Contribution of asphalt modified crumb rubber, using BNAR and tire rubber powder is increasing the skid number, which is mix in warm temperature and hot temperature. By increasing the number of viscosity it will increase the skid number from different content.
"
Depok: Fakultas Teknik Universitas Indonesia, 2015
S60280
UI - Skripsi Membership  Universitas Indonesia Library
cover
Limbong, Renhard Halomoan
"Penelitian ini bertujuan untuk dapat mengetahui kinerja mekanis dari Aspal Retona Refine Buton Asphalt , Agregat, dan campuran beraspal Asphalt Concrete Wearing Course AC ndash; WC yang menggunakan bahan modifikasi Crumb Rubber sebanyak 1,9 ; 3,3 ; dan 4,7 dari berat total agregat dan menggantikan gradasi agregat halus saja. Dari semua komposisi modifikasi didapatkan Kadar Aspal Optimum KAO dengan metode Marshall. Pengujian Marshall juga menggunakan metode Immersion untuk mengetahui Indeks Kekuatan Sisa IKS.
Dalam penelitian ini juga mencari Modulus Resilien yang didapatkan dari hasil uji UMATTA Universal Material Testing Apparatus . Hasil terbesar Modulus Resilien didapat dari campuran 0 Crumb Rubber atau tanpa campuran dengan nilai 2805 MPa dengan suhu 250C dan nilai penurunan terbesar akibat Immersion adalah pada komposisi Crumb Rubber 1,9 di suhu 250C dengan penurunan sebesar 32,30.

This research is intended to be able to know the mechanical performance of Asphalt Concrete Wearing Course AC WC asphalt Retona Fixed Buton Asphalt , Aggregate and Asphalt Concrete Wearing Course AC WC with 1.9x Crumb Rubber modification 3.3 and 4.7 of the total aggregate weight and fine aggregate gradation. From the all modified composition of Asphalt Optimum KAO with Marshall method. Marshall tests also use Immersion method to find out the Time Strength Index IKS.
The research also look for Resilient Modulus generated from the test results of UMATTA Universal Material Test Equipment . The highest yield of Resilient Modulus was obtained from a mixture of 0 Crumb Rubber or without mixture with a value of 2805 MPa with a temperature of 250C and the highest value due to Immersion was at 1.9 Crumb Rubber composition at a temperature of 250C with a decrease of 32.30.
"
Depok: Fakultas Teknik Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Muhammad Syaebani
"Penelitian ini menggunakan metode teknologi campuran beraspal hangat yang memungkinkan pengurangan temperatur pada campuran aspal. Penggunaan BNA-R sebagai bahan tambah pada campuran hangat diharapkan sebagaimana dapat mengurangi dampak buruk lingkungan yang dihasilkan dari metode hotmix, serta lebih ramah lingkungan. Proses pencampuran aspal dengan BNA-R yaitu dengan menggunakan alat pengaduk modifikasi dengan kecepatan maksimum 3000 rpm. Penelitian ini dilaksanakan di Laboratorium Bahan dan Material Departemen Teknik Sipil, Fakultas Teknik, Universitas Indonesia, dan Laboratorium BBPJN IV, Cikampek-Karawang, Jawa Barat. Kadar BNA-R yang digunakan yaitu 10%, 15%, 20%, dan 25%. Penelitian ini menggunakan variasi kadar aspal 5%, 5,5%, 6%, 6,5%, dan 7% untuk mendapatkan kadar aspal optimum dan digunakan sebagai acuan awal dalam job mix penelitian ini. Lalu dilakukan analisis dengan metode deskriptif analitis, yaitu dengan analisis regresi dan korelasi. Hasil penelitian menunjukkan hubungan yang kuat antara nilai ITS dengan MR yaitu dengan persamaan ?MR (MPa) = 0,010 ITS ^1,236?, dengan R² = 0,837. Selain itu terdapat pola hubungan antara nilai ITS dengan kadar BNA-R dimana pertambahan BNA-R akan meningkatkan nilai ITS. Pola tersebut dinyatakan dalam persamaan ?y = 3306x² - 1049x + 836.2?. Sedangkan, pola hubungan antara Modulus Resilien dengan kadar BNA-R dinyatakan dalam persamaan ?y = 20900x² - 5658x + 9138?.

This research used warm-mix asphalt technology which allows a reduction in the temperature of the asphalt mix. The used of BNA-R additive as material added to enhance performance of the asphalt with penetration 60/70 mixture of bitumen and the warm-mix asphalt are expected to reduce the bad effects of hot-mix method, also more environmentally-friendly. Mixing process of asphalt modified was used modification mixer with max. 3000 rpm. This research was conducted at the Laboratory of Substances and Materials Department of Civil Engineering, Faculty of Engineering, University of Indonesia, and Laboratory BBPJN IV, Cikampek-Karawang,West Java. The BNA-R content that have been used are 10%, 15%, 20%, and 25%. This research used a variation of asphalt content; 5%, 5.5%, 6%, 6.5%, and 7%, to obtain the optimum aspalt content. Researcher must find the optimum asphalt content first before starting to mix the modification of the asphalt.. Then analyzed with descriptive analytical method; the regression and correlation analysis.The result of this research show the strength relation between ITS value and Resilient Modulus with equation ?MR (MPa) = 0,010 ITS ^1,236?, dengan R² = 0,727. In order that, there is a relation either between ITS value and BNA-R content that made in equation ?y = 3306x² - 1049x + 836.2?. And then, there is a relation too between Resilient Modulus and BNA-R content which ?y = 20900x² - 5658x + 9138?."
2015
S60253
UI - Skripsi Membership  Universitas Indonesia Library
cover
Eva Azhra Latifa
"Tesis ini membahas pengaruh temperatur dan pembebanan terhadap sifat mekanis beton aspal campuran panas gradasi agregat menerus AC-WC dan senjang HRS. Dilakukan pengujian menggunakan Umatta serta Wheel Tracking Device. Data diolah dengan faktorial desain analisis.
Kesimpulan: Kedua macam gradasi, variasi temperatur serta pembebanan berpengaruh signifikan terhadap regangan tarik, tegangan tarik, modulus resilien, stabilitas dinamis, nilai serta laju deformasi permanen dalam merespon variasi pembebanan dan temperatur, namun HRS lebih kuat dari AC-WC.

This thesis discusses the temperature and loading's influence on the hot mix asphaltic concrete's mechanical properties AC-WC dense graded and the HRS aggregate's gap. The test is done using UMATTA and Wheel Tracking Device. The data is analyzed using factorial design analysis.
Conclusions: Both kinds of gradation, temperature and loading variation have significant effect on strain tensile, tensile strength, modulus resilient, dynamic stability, the rate of permanent deformation and deformation value. Both types of aggregate gradation show the same pattern and tendency to respond the loading and temperature variation, but HRS is stronger.
"
Depok: Fakultas Teknik Universitas Indonesia, 2011
T30802
UI - Tesis Open  Universitas Indonesia Library
cover
Muhammad Naldo Jabari Mulya
"Saat ini Asbuton telah banyak digunakan sebagai alternatif pengganti aspal konvensional pada pembangunan jalan raya. Pertimbangannya adalah keberadaan serta harga aspal minyak selalu cenderung meningkat seiring fluktuasi harga minyak bumu dunia yang meningkat. Pemelitian ini memiliki tujuan untuk mengetahui persentase kadar aspal dan agregat yang terkandung dalam Asbuton Lawele Granular Asphalt (LGA), mengetahui kadar penggunaan limbah beton pada campuran beraspal terhadap nilai parameter Marshall dengan mempertimbangkan kandungan mortarnya.dan mengetahui rancangan susunan agregat baru dan agregat limbah beton untuk mendapatkan Asbuton paving block berpori. Penelitian kali ini diawali dengan pengujian karakteristik agregat, aspal pen 60/70, dan ekstraksi LGA. Untuk mendapatkan kadar aspal serta agregat yang terkandung dalam LGA dapat dilakukan dengan ekstraksi butiran LGA menggunakan metode Reflux dan Centrifuge. Bitumen dan agregat yang sudah ter-ekstrak kemudian diuji karakteristik agregat dan aspalnya. Aspal yang ter-ekstrak dari butiran LGA memiliki nilai penetrasi yang rendah, sehingga perlu penambahan oli bekas untuk menaikan nilai penetrasi. Setelah semua bahan sudah diuji kemudian dilanjutkan dengan pembuatan benda uji untuk mencari nilai kadar aspal optimum sebanyak 30 total, 15 untuk benda uji aspal dengan agregat baru dan 15 untuk benda uji aspal yang ditambahkan agregat limbah beton. Kemudian sampel akan diuji Marshall Standard berguna untuk mendapatkan nilai KAO. Setelah nilai KAO didapatkan dilanjutkan pembuatan benda uji pavingblock dengan ukuran 25x25x6,5 cm sebanyak 6 buah, 3 untuk campuran tanpa RCA dan 3 buah untuk benda uji menggunakan RCA. Setelah sampel pavingblock dibuat, dilakukan proses core drill sebanyak dua lubang setiap satu pavingblock yang akan diuji nilai volumteriknya dengan uji Marshall Standard dan Immersion. Kemudian dilihat apakah ada pengaruh terhadap nilai volumetric pada pavingblock dan compact standard. Hasil yang didapatkan dari pengujian adalah Asbuton Lawele Granular Asphalt (LGA) memiliki kanduangan bitumen sebanyak 26% dan kandungan agregat sebanyak 73%, komposisi yang digunakan untuk campuran agregat baru tanpa menggunakan RCA yang didapat dari blending agregat yaitu 52% agregat kasar, 40% agregat halus, dan 8% agregat LGA, sedangkan untuk campuran dengan tambahan RCA memiliki komposisi 23% RCA, 29% agregat kasar, 20% agregat halus, dan 8% agregat LGA, kadar aspal optimum yang di dapat dari campuran agregat baru tanpa menggunakan RCA dan campuran dengan tambahan RCA adalah 7%, dan berdasarkan hasil volumetrik dan pengujian marshall menunjukkan bahwa campuran dengan menggunakan agregat baru masih lebih baik dari campuran dengan menggunaan RCA sebagai subtitusi agregat baru.

Currently, Asbuton has been widely used as an alternative to conventional asphalt in highway construction. The consideration is that the existence and price of petroleum asphalt always tends to increase along with increasing fluctuations in world petroleum prices. This research aims to determine the percentage of asphalt and aggregate content contained in Asbuton Lawele Granular Asphalt (LGA), determine the level of use of concrete waste in the asphalt mixture against the Marshall parameter value by considering the mortar content, and determine the design of the new aggregate composition and waste concrete aggregate for get porous Asbuton paving blocks. This research began with testing the characteristics of aggregate, asphalt pen 60/70, and LGA extraction. To obtain the asphalt and aggregate content contained in LGA, extraction of LGA granules can be done using the Reflux and Centrifuge methods. The extracted bitumen and aggregate are then tested for the characteristics of the aggregate and asphalt. Asphalt extracted from LGA granules has a low penetration value, so it is necessary to add used oil to increase the penetration value. After all the materials have been tested then proceed with making test objects to find the optimum asphalt content value of 30 in total, 15 for asphalt test objects with new aggregate and 15 for asphalt test objects with added concrete waste aggregate. Then the sample will be tested using the Marshall Standard to get the KAO value. After the KAO value was obtained, 6 pieces of pavingblock test specimens measuring 25x25x6.5 cm were continued, 3 for the mixture without RCA and 3 for non-RCA test objects and 3 for test objects using RCA. After the paving block samples are made, a core drill process is carried out with two holes for each paving block which will be tested for their volumetric value using the Marshall Standard and Immersion tests. Then see whether there is an influence on the volumetric value of standard paving blocks and compacts. The results obtained from the test were that Asbuton Lawele Granular Asphalt (LGA) had a bitumen content of 26% and an aggregate content of 73%. The composition used for the new aggregate mixture without using RCA was obtained from blending the aggregate, namely 52% coarse aggregate, 40% aggregate fine, and 8% LGA aggregate. Meanwhile, the mixture with the addition of RCA has a composition of 23% RCA, 29% coarse aggregate, 20% fine aggregate, and 8% LGA aggregate. The optimum asphalt content obtained from the new aggregate mixture without using RCA and the mixture with the addition of RCA is 7%. Based on the volumetric results and Marshall testing, it shows that the mixture using new aggregate is still better than the mixture using RCA as a substitute for new aggregate."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
William
"Limbah plastik adalah salah satu persoalan utama dalam manajemen lingkungan. Dari semua jenis limbah plastik, kemasan makanan berbasis polipropilena (PP) memiliki kesulitan tersendiri untuk didaur ulang. Struktur kemasan yang berbasis polipropilena multi lapis ini mempersulit serta meningkatkan biaya daur ulang. Pada saat yang bersamaan, persoalan mengenai kualitas jalan yang buruk masih dialami daerah-daerah di Indonesia. Untuk menyelesaikan kedua persoalan ini, telah dilakukan berbagai upaya untuk menggunakan limbah plastik sebagai modifier aspal. Penambahan plastik seharusnya dapat meningkatkan karakteristik perkerasan aspal. Namun, perbedaan sifat permukaan plastik dengan bitumen menimbulkan kesulitan dalam proses pencampuran dan mengorbankan kualitas akhir. Oleh sebab itu, penelitian ini mengajukan upaya modifikasi sifat permukaan dari limbah multi lapis demi meningkatkan kompatibilitas campuran bitumen termodifikasi polimer. Metode yang digunakan adalah metode plasma dingin dan oksidasi termal untuk mengubah sifat kimia dari limbah plastik. Dalam penelitian ini, plastik termodifikasi ditambahkan ke dalam bitumen untuk menghasilkan campuran bitumen termodifikasi polimer, dengan variasi kadar 1, 3, dan 5 wt.%. Pengujian daktilitas, penetrasi, serta mikroskop optik dilakukan untuk mengetahui karakteristik campuran bitumen. Kemudian, campuran ini dijadikan sebagai binder untuk perkerasan aspal. Karakterisasi perkerasan aspal dilakukan dengan pengujian Marshall. Hasil pengujian mengindikasikan bahwa modifikasi permukaan meningkatkan kompatibilitas antara limbah plastik dengan bitumen, serta campuran bitumen termodifikasi polimer ini pun meningkatkan sifat stabilitas dan densitas dari perkerasan aspal. Peningkatan stabilitas Marshall mencapai 837 kg terjadi pada penambahan plastik sebanyak 5 wt.%.

Plastic waste is one of the leading issues in environmental management. From all kinds of plastic waste, multilayered polypropylene food packaging particularly poses a huge challenge in its recycling. The multi-layered, polypropylene-based (PP) structure of these packaging increases the complication and cost of recycling. At the same time, issues regarding poor-quality roads still plague regions in Indonesia. Hence, there have been efforts to utilize plastic waste as asphalt modifiers. On paper, plastic addition should increase the properties of asphalt paving. However, the difference in surface properties between plastic and bitumen has brought rise to difficulties in the mixing process and sacrificed the end-quality as a result. As such, this research proposes to modify the surface properties of the multilayer waste to increase the compatibility of the polymer-modified bitumen mix. The method proposed is to use Dielectric Barrier Discharge Plasma treatment and thermal oxidization to alter the chemical properties of the plastic waste. In this research, modified plastic waste is added into bitumen to create a polymer-modified bitumen mix, with 1, 3, and 5 wt.% variations. Ductility testing, penetration testing, and optical microscopy are conducted to examine the characteristics of the bitumen mix.  This mix in turn acts as a binder for asphalt concrete to investigate the performance. To examine the properties of the asphalt concrete, Marshall Testing is conducted. Test results indicate that surface modification does indeed increase the compatibility of plastic waste and bitumen, with the polymer-modified bitumen mix acting as a binder for asphalt concrete increases stability and density properties. Marshall stability increase of 837 kg is reached with the addition of 5 wt.% plastic. "
Depok: Fakultas Teknik Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>