Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 100310 dokumen yang sesuai dengan query
cover
Angga Romana
"Listrik dengan sumber energi terbarukan terus mengalami peningkatan, namun tidak banyak di indonesia yang memanfaatkan energi tersebut untuk suatu pembangkit listrik yang mandiri dan optimal, salah satunya ialah di Desa Kolorai, morotai selatan. Dengan memanfaatkan Solar panel PV sebagai alat untuk mengubah energi matahari menjadi energi listrik, dan berdasarkan data yang diberikan oleh NASA, tingkat radiasi matahari di daerah kolorai sangat besar yaitu sekitar 5,99 kWh/ /day. Sehingga sistem PLTS mandiri merupakan salah satu solusi untuk pengadaan listrik di tempat yang terisolir aliran listrik seperti di daerah kolorai. Oleh karena itu, dalam menentukan profil beban dan langkah untuk mendesain sistem sangat berpengaruh untuk membangun sistem stand alone PV yang memenuhi syarat ekonimis dan teknis. Maka diperlukan suatu metode yang optimal untuk merancang sistem tersebut, dimana energi yang di hasilkan besar namun energi yang terbuang kecil dan memiliki nilai NPC yang rendah. Sehingga dengan membandingan metode perhitungan dengan menggunakan Standar Australia/New Zealand dan perhitungan manual Morteza Khatami untuk mendapatkan desain yang ekonimis dan teknis. Hasil simulasi pada homer menunjukan dengan menggunakan Standar Australia/New Zealand memiliki hasil yang sesuai dengan syarat yang diinginkan dengan nilai excess electricitynya sebesar 8,56 dan biaya NPC sebesar Rp 1.439.160.000,00.

Electricity with renewable energy sources continues to increase, but not many in Indonesia utilize that energy for an independent and optimal power plant, one of them is in Kolorai Village, south morotai. By utilizing Solar panel PV as a tool to convert solar energy into electrical energy, and based on data provided by NASA, the level of solar radiation in the colourai area is very large at around 5.99 kWh day. So the PV off grid system is one of the solutions for the procurement of electricity in an isolated place such as the flow of electricity in the area kolorai. Therefore, in determining the load profile and the steps to design the system is very influential to build a stand alone PV system that meets the economic and econimical requirements. Therefore it is necessary an optimal method for designing the system, where the energy produced is large but the energy is wasted small and has a low NPC value. Therefore, by comparing the method of calculation using the Australian New Zealand Standard and manual calculations to obtain an eco technical and technical design. The result of simulation on homer showed by using Australian New Zealand Standard has result according to requirement with excess electricity value equal to 8,56 and cost of NPC equal to Rp1.439.160.000,00. "
Depok: Fakultas Teknik Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Mutiara Sani
"Listrik dengan sumber energi terbarukan terus mengalami peningkatan. Namun tidak banyak di Indonesia yang memanfaatkan energi tersebut untuk suatu pembangkit listrik yang mandiri dan optimal.Dengan Photovoltaics (PV) sebagai alat yang menyerap dan mengubah energi matahari menjadi energi listrik, maka energi listrik yang dihasilkan dari sumber energi matahari tersebut diperkirakan sangat besar hasilnya. Maka dari itu Sistem Stand Alone Photovoltaic merupakan sebuah solusi untuk pengadaan listrik di tempat yang terisolir aliran listrik ataupun bagi yang ingin memiliki sistem listrik sendiri baik untuk tempat tinggal ataupun tempat usaha.
Profil beban dan langkah mendesain sistem sangat berpengaruh untuk membangun sebuah sistem Stand Alone Photovoltaic yang optimal sesuai kebutuhan, yaitu meliputi ukuran array PV, sistem baterai dan inverter serta efektivitas biayamenjadi sebuah faktor .Maka dari itu perlu suatu metode yang optimal untuk merancang sistem tersebut, dimana energi yang dihasilkan besar namun memiliki biaya awal yang rendah. Maka dari itu dengan membandingkan tiga buah metode perancangan sistem, akan mendapatkan metode yang paling optimal dengan energi yang besar yaitu 20172,8 Wh dan dengan nilai biaya awal yang rendah yaitu Rp 78,400,000 untuk merancang sebuah sitem Stand Alone Photovoltaic, sehingga energi matahari pun dapat dioptimalkan sebagai pembangkit listrik.

Electricity with renewable energy sources continues to increase. But not many in Indonesia who make use of the energy for an independent power plant and optimal. With Photovoltaics (PV) as a tool to absorb and convert solar energy into electrical energy, then the energy is electricity generated from solar energy sources are estimated to be very big results. Therefore Stand Alone Photovoltaic System is a solution for the provision of electricity in place of isolated power or for those who want to have its own electricity system both for the residence or place of business.
Load profile and designed the highly influential system to build a Stand Alone Photovoltaic systems are optimal, which include the size of the PV array, battery and inverter system as well as cost effectiveness is becoming a factor. Therefore need an optimum method to design the system, where energy produced large but has a lower initial cost. Thus by comparing the three methods in the design of the system, will get the most optimal method with great energy that is 20172,8 Wh and the low initial cost of $ 78,400 million to design a system for Stand Alone Photovoltaic Solar energy, which can also be optimized as a power plant.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
S46447
UI - Skripsi Membership  Universitas Indonesia Library
cover
Anita Faradilla
"Pemilihan lokasi dan desain sistem energi surya merupakan tahapan yang sangat penting dalam memastikan kelayakan, keberlanjutan, dan operasional yang optimal suatu Pembangkit Listrik Tenaga Surya (PLTS). Banyak hal yang perlu dipertimbangkan dalam evaluasinya, seperti posisi (spasial) dan kondisi suatu wilayah (geospasial). Oleh karena itu, penelitian ini bertujuan untuk mengembangkan skema atau rancangan pengambilan keputusan untuk pemilihan lokasi PLTS yang sesuai, khususnya di desa tertinggal, terdepan, dan terluar (3T) Indonesia dengan metode yang digunakan adalah kombinasi Geographical Information System (GIS) dan pendekatan pengambilan keputusan multi-kriteria (MCDM), serta optimisasi desain sistem PLTS dengan menggunakan perangkat lunak HOMER untuk daerah paling sesuai berdasarkan analisis geospasial GIS-Analytic Hierarchy Process (AHP). Hasil yang didapatkan adalah kriteria yang paling berpengaruh adalah kriteria iklim (GHI 32%, temperatur 21%, dan kelembaban 5%). Daerah yang paling sesuai untuk PLTS adalah Desa Kalibagor, Desa Tulamben, Desa Tolada, Desa Kotaraja, Desa Talaga Tomoagu, Desa Maronge, dan Desa Nelelamawangi, sedangkan desa 3T yang sesuai untuk PLTS adalah Desa Kafelulang, Desa Pendulangan, dan Desa Sampuro. Kapasitas PLTS di daerah paling sesuai berada pada rentang 45,7 s/d 2.973 kW dengan produksi listrik yang dihasilkan sebanyak 69.718 s/d 4.457.825 kWh/tahun, sedangkan di desa 3T 79,4 s/d 146 kW dengan produksi listrik yang dihasilkan sebanyak 97.685 s/d 247.234 kWh/tahun. Rentang nilai Levelized Cost of Electricity (LCOE) untuk daerah paling sesuai adalah Rp4.119/kWh s/d Rp4.639/kWh, sedangkan untuk desa 3T adalah Rp4.201/kWh s/d Rp4.808/kWh.

Site selection and solar energy system design are very important stages in ensuring the feasibility, sustainability, and optimal operation of a Solar PV Power Plant. Many things need to be considered in the evaluation, such as the position (spatial) and condition of an area (geospatial). Therefore, this study aims to develop a decision-making scheme or design for the selection of suitable solar PV locations, especially in disadvantaged, frontier, and outermost (3T) villages in Indonesia. The method used is a combination of Geographical Information System (GIS) and a multi-criteria-decision-making approach (MCDM), as well as optimization solar energy system design using HOMER software for the highly suitable area based on GIS-Analytic Hierarchy Process (AHP). The results obtained are the most influential criteria are climate (GHI 32%, temperature 21%, and humidity 5%). The highly suitable areas for solar PV power plant are Kalibagor Village, Tulamben Village, Tolada Village, Kotaraja Village, Talaga Tomoagu Village, Maronge Village, and Nelelamawangi Village, while the 3T villages that are suitable for PLTS are Kafelulang Village, Pendulangan Village, and Sampuro Village. Solar PV capacity in the highly suitable area varies between 45.7 and 2,973 kW with electricity production of 69,718 to 4,457,825 kWh/year, while in 3T villages varies 79.4 to 146 kW with electricity production of 97,685 to 247,234 kWh/year. Levelized Cost of Electricity (LCOE) in the highly suitable area varies between 4,119 IDR/kWh to 4,639 IDR/kWh, while in 3T villages varies 4,201 IDR/kWh to 4,808 IDR/kWh."
Depok: Fakultas Teknik Universitas Indonesia, 2022
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Hutapea, Kevin Samuel Ivan Siantra
"Energi listrik merupakan salah satu faktor terpenting dalam kehidupan manusia hingga saat ini. Oleh karena itu, apabila terdapat suatu kawasan yang telah menjadi pemukiman masyarakat, maka sangat mendesak tempat tersebut untuk mendapatkan suplai energi listrik yang sesuai dengan kebutuhan. Namun, ada beberapa daerah di Indonesia yang masih belum mendapatkan pasokan listrik. Salah satu daerah yang belum mendapat pasokan listrik yang cukup adalah Kalimantan Barat. Masih ada beberapa daerah di Kalbar yang pasokan listriknya belum memenuhi kebutuhan, terutama saat terjadi beban puncak. Untuk mengatasi hal tersebut, pemerintah Indonesia melalui PLN mengadakan kesepakatan untuk mengimpor listrik dari Sarawak, Malaysia. Penulis melihat ada alternatif lain untuk memenuhi kebutuhan listrik yaitu dengan memanfaatkan energi terbarukan. Posisinya yang dilintasi garis khatulistiwa menjadikan pembangkit listrik tenaga surya sebagai salah satu solusi alternatif yang dapat ditetapkan untuk memenuhi kebutuhan listrik Kalbar. Dalam tugas akhir ini, penulis merancang konfigurasi sistem pembangkit listrik tenaga surya dan mengkaji lebih jauh aspek keekonomiannya dibandingkan dengan daya eksisting yang dipasok dari Malaysia. Analisis tekno-ekonomi akan dilakukan untuk menganalisis sistem tenaga energi terbarukan dengan sumber surya. Dengan demikian dapat dilihat dan dianalisis perbandingannya dari segi biaya keseluruhan, keandalan, kelayakan, dan efektivitas. Aspek optimasi penelitian ini adalah, net present cost (NPC), renewable penetration, dan cost of energy (COE). Tesis ini akan memberikan evaluasi kinerja keuangan dan energi dari solusi yang diusulkan menggunakan HOMER Pro. Hasil simulasi menunjukkan bahwa dengan penerapan photovoltaic dapat menekan biaya produksi energi karena separuh produksinya berasal dari energi terbarukan. Hasil penelitian ini juga menunjukkan bahwa penerapan sistem PV on-grid dapat mempercepat penyediaan listrik di Kalimantan Barat.

Electrical energy is one of the most important factors in human life until this day. Therefore, if there is an area that has become a community settlement, it is urgent for that place to get the supply of electrical energy as needed. However, there are some areas in Indonesia that still have not received electricity supply. One of the areas that has not received sufficient electricity supply is West Kalimantan. There are still several areas in West Kalimantan where the electricity supply has not met demand, especially when peak loads occur. To overcome this, the Indonesian government through PLN entered into an agreement to import electricity from Sarawak, Malaysia. Author sees there are another alternative option to meet electricity needs which is by utilizing renewable energy. Its position which is crossed by the equator makes solar power plants one of the alternative solutions that can be set to fulfill West Kalimantan's electricity needs. In this thesis, author designed a configuration of solar power plant system and investigate further about the economical aspect comparing to existing power that supplied from Malaysia. Techno-economic analysis will be conducted to analyze the renewable energy power system with solar sources. By that way, it can be seen and analyzed the comparison in terms of overall cost, reliability, feasibility, and effectiveness. The aspects of optimizing this research are, net present cost (NPC), renewable penetration, and cost of energy (COE). This thesis will provide a financial and energy performance evaluation of the proposed solution using HOMER Pro. The result of the simulation shows that by implementing photovoltaic it can reduce the cost of energy since the half of production comes from renewable energy. The result of this research also shows that implementing on-grid PV system can accelerate electricity provision in West Kalimantan."
Depok: Fakultas Teknik Universitas Indonesia, 2021
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Agastya Nugraha Putra
"Indonesia memiliki potensi sumber daya energi baru dan terbarukan yang besar, salah satu diantaranya adalah sumber energi surya. Teknologi yang digunakan untuk mengonversi energi surya menjadi listrik adalah sel surya. Pemasangan pembangkit listrik tenaga surya pada atap gedung-gedung diharapkan dapat meningkatkan bauran energi EBT nasional dan dapat meningkatkan efisiensi energi listrik gedung tersebut. Penelitian ini bertujuan untuk mengetahui karakteristik energi surya pada Rest Area km 260B Banjaratma dan mengetahui pengaruh pemasangan pembangkit listrik tenaga surya atap terhadap efisiensi energi listrik. Penelitian ini dilakukan dengan cara membandingkan iradiasi matahari pengukuran langsung dengan iradiasi matahari proyeksi perangkat lunak berdasarkan data historis. Perhitungan proyeksi efisiensi energi listrik menggunakan data iradiasi matahari proyeksi perangkat lunak. Hasil pengujian menunjukkan bahwa karakteristik energi surya pada Rest Area km 260B Banjaratma dapat mencapai rata-rata iradiasi matahari sebesar 306 W/m2 pada hari dengan cuaca cerah berawan, namun hanya mencapai rata-rata iradiasi matahari sebesar 188 W/m2 pada hari yang terdapat cuaca hujan. Berdasarkan perhitungan, pemasangan pembangkit listrik tenaga surya dapat meningkatkan efisiensi energi listrik bangunan sebesar 1,2% pada tahun pertama operasi dan terus turun hingga 0,8% pada tahun kelima beroperasi. Dengan demikian, dapat disimpulkan bahwa pemasangan pembangkit listrik tenaga surya atap dapat meningkatkan efisiensi energi listrik bangunan.

To meet the energy demand, Indonesia still relies on the use of fossil fuels. The utilization of new and renewable energy is still far from the target even though Indonesia has the potential sources of new and renewable energy, such as solar energy. The technology used to convert solar energy into electricity is a solar cell. The installation of rooftop solar power plant on the buildings hopefully will increase the renewable energy ratio toward national electricity source mix and increase the electrical energy efficiency of the buildings. The objectives of this research is to determine the characteristics of solar energy in the Rest Area km 260B Banjaratma and determine the effect of installing a rooftop solar power plant on building electrical energy efficiency. This research was conducted by comparing direct measurement solar irradiation with software projected solar irradiation based on historical data. Calculation of building electrical energy efficiency projections is using data from software projection solar irradiation. Test results show that the characteristics of solar energy in the Rest Area km 260B Banjaratma can reach an average solar irradiation of 306 W/m2 on day with clear and cloudy weather, but only reach an average solar irradiation of 188 W/m2 on day with rainy weather. Based on calculation, installing a rooftop solar power plant can increase building electrical energy efficiency by 1,2% in the first year of operation and decrease to 0,8% in the fifth year of operation. Thus, it can be concluded that installing rooftop solar power plants can increase building electrical energy efficiency.
"
Depok: Fakultas Teknik Universitas Indonesia, 2024
PR-PDF
UI - Tugas Akhir  Universitas Indonesia Library
cover
Muhammad Farhan Mahandika
"Menurut data dari United Nations Development Program (UNDP), perairan Indonesia merupakan habitat bagi 76% terumbu karang dan 37% ikan karang dunia. Menurut data Kementrian Kelautan dan Perikanan Indonesia, jumlah potensi ikan di lautan Indonesia adalah sebesar 12,54 juta ton pertahun. Namun, Indonesia masih belum bisa memanfaatkan potensi tersebut karena jumlah produksi perikanan tangkap di Indonesia masih sebesar 6,83 ton per tahun. Salah satu alat tangkap perikanan di Indonesia adalah bagan apung yangmemiliki produktivitas yang baik untuk menangkap ikan. Selain itu, SDA nonhayati Indonesia pun melimpah,seperti minyak bumi misalnya. Namun, Ilmuwan memprediksi bahwa energi minyak bumi Indonesia tersebut akan habis pada 2030. Jika Indonesia masih bergantung kepada energi fossil tersebut dan tidak mencari energi alternatif, maka dikhawatirkan Indonesia tidak siap menghadapi kehidupan yang akan mendatang. Selain ketersediannya mulai menipis, energi fossil pun memberikan dampak yang buruk terhadap lingkungan. Menurut Intergovernmental Panel On Climate Change (IPCC), 1 liter BBM jenis premium dapat menghasilkan 2,35 Kg gas CO2. Jika satu bagan Apung berukuran 10 meter x 9 meter membutuhkan 1.907 Liter selama setahu, maka gas CO2 yang dihasilkan sebesar 4.481 Kg. Salah satu usaha yang dapat dilakukan untuk mengurangi emisi tersebut adalah dengan cara mengganti BBM menjadi tenaga surya yang ramah terhadap lingkungan. Selain itu, penggunakan Pembangkit Listrik Tenaga Surya pun lebih menguntungkan daripada pembangkit listrik generator set dalam jangka waktu minimal 4 tahun.

According to data from the United Nations Development Program (UNDP), Indonesian waters are a habitat for 76% of the world's coral reefs and 37% of reef fish. According to data from the Indonesian Ministry of Maritime Affairs and Fisheries, the potential number of fish in Indonesia's oceans is 12.54 million tons per year. However, Indonesia is still unable to exploit this potential because the amount of capture fisheries production in Indonesia is still 6.83 tons per year. One of the fishing gear in Indonesia is a floating fishing platform that has good productivity for fishing. In addition, Indonesia's non-biological natural resources are abundant, such as petroleum for example. However, scientists predict that Indonesia's petroleum energy will run out by 2030. If Indonesia still relies on fossil energy and does not look for alternative energy, then it is feared that Indonesia is not ready to face life to come. In addition to its diminishing availability, fossil energy also has a bad impact on the environment. According to the Intergovernmental Panel on Climate Change (IPCC), 1 liter of premium fuel can produce 2.35 kg of CO2 gas. If a floating meter measuring 10 meters x 9 meters requires 1,907 liters for one year, the CO2 gas produced is 4,481 kg. One effort that can be done to reduce these emissions is by replacing fuel into solar power that is friendly to the environment. In addition, the use of solar power plants is more profitable than generating sets for a minimum of 4 years."
Depok: Fakultas Teknik Universitas Indonesia , 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Clarissa Stellavania
"Mengikuti perkembangan industri kendaraan listrik di Indonesia, PT Transportasi Jakarta (Transjakarta) telah menyediakan 52 unit bus listrik untuk beroperasi dengan suplai listrik yang disediakan oleh PLN seluruhnya. Sayangnya, 86,95% dari total produksi listrik di Indonesia pada tahun 2020 berasal dari bahan bakar fosil. Untuk mengatasi permasalahan emisi gas rumah kaca dan cadangan energi fosil yang menipis, Kementerian ESDM mencanangkan Kebijakan Energi Nasional (KEN) yang menargetkan pencapaian EBT sebesar 23% pada tahun 2025. Sayangnya, pemenuhan target tersebut masih cukup jauh dengan pemanfaatan energi surya sebagai PLTS di Indonesia masih sangat kecil, yaitu sekitar 0,2 GW dari potensi yang mencapai lebih dari 200 GW. Implementasi yang minim ini disebabkan oleh beberapa faktor seperti kebutuhan lahan dan kebutuhan modal. Salah satu solusi terhadap permasalahan ini adalah pemasangan PLTS pada kendaraan listrik. Hasil analisis teknis didukung oleh hasil perhitungan ekonomi dan analisis risiko dengan metode Monte Carlo menunjukkan bahwa pemasangan PLTS pada bus listrik Transjakarta dengan modul monocrystalline layak untuk dilaksanakan. Kelayakan investasi menghasilkan Net Present Value sebesar Rp54.777.292, Internal Rate of Return sebesar 13,02%, Payback Period sebesar 6,41 tahun, dan Profitability Index sebesar 1,47 untuk menghasilkan daya 12,275 MWh/tahun dengan derajat keyakinan parameter NPV, IRR, PBP, dan PI > 50%.

As Indonesia's electric vehicle market grew, PT Transportasi Jakarta (Transjakarta) provided 52 electric bus units that run solely on PLN power. However, fossil fuels contributed to 86.95% of Indonesia's entire electricity output in 2020. In fact, 2.3% of the world's total greenhouse gas emissions came from Indonesia, where 1.24 gigatons of carbon dioxide were emitted. The Ministry of Energy and Mineral Resources proposed the National Energy Policy (KEN), which aims to reach a 23% share of renewable energy by 2025, in order to address the issues of greenhouse gas emissions and the dwindling amount of fossil fuel reserves. Unfortunately, this objective is still a long way off. One example is the relatively low adoption of solar energy as solar power plant in Indonesia, which currently at about 0.2 GW out of a potential of over 200 GW. There are a few reasons for this minimum implementation, including capital and land requirements. A potential solution to solve this issue is to install rooftop solar power systems on top of electric buses. The results of the technical analysis supported by the results of economic calculations and risk analysis with the Monte Carlo method show that the installation of PLTS on Transjakarta electric buses with monocrystalline modules is feasible to implement. The investment feasibility resulted in a Net Present Value of IDR 54,777,292, an Internal Rate of Return of 13.02%, a Payback Period of 6.41 years, and a Profitability Index of 1.47 to produce 12.275 MWh/year of power with a degree of confidence in the NPV, IRR, PBP, and PI parameters > 50%."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Clarissa Stellavania
"Mengikuti perkembangan industri kendaraan listrik di Indonesia, PT Transportasi Jakarta (Transjakarta) telah menyediakan 52 unit bus listrik untuk beroperasi dengan suplai listrik yang disediakan oleh PLN seluruhnya. Sayangnya, 86,95% dari total produksi listrik di Indonesia pada tahun 2020 berasal dari bahan bakar fosil. Untuk mengatasi permasalahan emisi gas rumah kaca dan cadangan energi fosil yang menipis, Kementerian ESDM mencanangkan Kebijakan Energi Nasional (KEN) yang menargetkan pencapaian EBT sebesar 23% pada tahun 2025. Sayangnya, pemenuhan target tersebut masih cukup jauh dengan pemanfaatan energi surya sebagai PLTS di Indonesia masih sangat kecil, yaitu sekitar 0,2 GW dari potensi yang mencapai lebih dari 200 GW. Implementasi yang minim ini disebabkan oleh beberapa faktor seperti kebutuhan lahan dan kebutuhan modal. Salah satu solusi terhadap permasalahan ini adalah pemasangan PLTS pada kendaraan listrik. Hasil analisis teknis didukung oleh hasil perhitungan ekonomi dan analisis risiko dengan metode Monte Carlo menunjukkan bahwa pemasangan PLTS pada bus listrik Transjakarta dengan modul monocrystalline layak untuk dilaksanakan. Kelayakan investasi menghasilkan Net Present Value sebesar Rp54.777.292, Internal Rate of Return sebesar 13,02%, Payback Period sebesar 6,41 tahun, dan Profitability Index sebesar 1,47 untuk menghasilkan daya 12,275 MWh/tahun dengan derajat keyakinan parameter NPV, IRR, PBP, dan PI > 50%.

As Indonesia's electric vehicle market grew, PT Transportasi Jakarta (Transjakarta) provided 52 electric bus units that run solely on PLN power. However, fossil fuels contributed to 86.95% of Indonesia's entire electricity output in 2020. In fact, 2.3% of the world's total greenhouse gas emissions came from Indonesia, where 1.24 gigatons of carbon dioxide were emitted. The Ministry of Energy and Mineral Resources proposed the National Energy Policy (KEN), which aims to reach a 23% share of renewable energy by 2025, in order to address the issues of greenhouse gas emissions and the dwindling amount of fossil fuel reserves. Unfortunately, this objective is still a long way off. One example is the relatively low adoption of solar energy as solar power plant in Indonesia, which currently at about 0.2 GW out of a potential of over 200 GW. There are a few reasons for this minimum implementation, including capital and land requirements. A potential solution to solve this issue is to install rooftop solar power systems on top of electric buses. The results of the technical analysis supported by the results of economic calculations and risk analysis with the Monte Carlo method show that the installation of PLTS on Transjakarta electric buses with monocrystalline modules is feasible to implement. The investment feasibility resulted in a Net Present Value of IDR 54,777,292, an Internal Rate of Return of 13.02%, a Payback Period of 6.41 years, and a Profitability Index of 1.47 to produce 12.275 MWh/year of power with a degree of confidence in the NPV, IRR, PBP, and PI parameters > 50%."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Arief Nurwanto
"ABSTRAK
Photovoltaic PV adalah salah satu energi terbarukan yang telah berkembang dan menjadi sumber energi yang menanjikan untuk digunakan di perumahaan. Oleh karena itu tenaga surya mandiri ini menjadi solusi sebagai sumber listrik di daerah pedesaan, dimana daerah tersebut tidak terjangkau oleh PLN. Karenanya, desain PV sistem yang optimum harus dilakukan untuk mencari sistem perancangan array PV yang memiliki biaya terjangkau. Di penelitian ini dengan membandingkan 2 metode, maka metode yang optimal untuk mendesain tenaga surya mandiri akan di dapatkan.

ABSTRACT
Photovoltaic PV , one of renewable energy has grown to become one of the most promising energy source for residential use. There by, Stand alone photovoltaic system is a solution as power plant in rural area that is not reach by electicity provider. The stand alone photovoltaic system depends on the load profile, battery sizing, and PV sizing. Hence, an optimal PV sizing and Battery sizing should be investigated to result an affordable PV array that will influence the cost. There fore, by comparing two method, then an optimum method for photovoltaic stand alone can be obtained.
"
Depok: Fakultas Teknik Universitas Indonesia, 2018
S70301
UI - Skripsi Membership  Universitas Indonesia Library
cover
Mario Reinzini
"Sistem grid-connected inverter untuk penerapan pada pembangkit listrik tenaga surya, diharapkan dapat menjadi sumber energi alternatif selain mengandalkan layanan jaringan listrik. Dengan sistem ini maka akan dapat diperoleh dan kemudian dianalisa dari dinamika sistem yang muncul. Sistem grid-connected inverter yang dibangun merupakan sistem yang terdiri dari model sel surya - rangkaian boost converter - inverter - beban - jaringan listrik. Algoritma Maximum Power Point Tracker (MPPT), algoritma Phase Locked Loop (PLL) dan current control merupakan metode kendali yang digunakan dalam sistem ini. Melalui rancangan sistem grid-connected inverter ini kemudian dilakukan simulasi untuk memperlihatkan respon sistem ketika sel surya memberikan suplai ke beban; maupun ketika sel surya dalam keadaan grid-connected. Sistem gridconnected dengan metode kendali MPPT belum dapat memberikan arus suplai dan tegangan yang sefasa, namun algoritma MPPT yang diterapkan telah mampu mencari titik kerja optimal dari sel surya pada kondisi lingkungan yang bervariasi, namun demikian sistem grid-connected dengan metode kendali PLL dan current control telah dapat menghasilkan arus suplai dan tegangan yang sefasa.

Grid-connected inverter system for solar power application expected to become an alternative energy source in addition to relying on electricity network services. Through this system we will be able to obtain a detail model and then analyzed the dynamics of the system itself. Grid-connected inverter system consist of : solar cells - a series boost converter - inverter - load - the electricity grid. Maximum Power Point Tracker algorithm (MPPT) algorithm Phase Locked Loop (PLL) and the current control is a control method used in this system. This gridconnected inverter system then simulated to demonstrate the system's response when the solar cells supply the load; as well as solar cells in grid-connected. Gridconnected systems with MPPT control methods have not been able to provide supply current and voltage are in phase, but the MPPT algorithm has been able to find the optimal point of the solar cells on the various environmental conditions, however, grid-connected system with PLL and current control methods control has been able to produce current and voltage are in phase supply."
Depok: Fakultas Teknik Universitas Indonesia, 2012
S42454
UI - Skripsi Open  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>