Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 143364 dokumen yang sesuai dengan query
cover
Shifa Nabila
"Serat jute merupakan salah satu serat alam yang ramah lingkungan dengan harga relatif murah dan volume produksi relatif tinggi. Polipropilena dipilih sebagai matriks karena sifat unggul yang dimiliki dan dapat didaur ulang. Penelitian ini bertujuan mengetahui pengaruh fraksi berat serat jute sebagai penguat pada matriks polipropilena untuk mendapatkan nilai optimum fraksi berat serat jute pada komposit. Serat jute mendapat perlakuan awal dengan alkalisasi. Fabrikasi komposit polipropilena diperkuat serat jute diawali dengan metoda ekstruksi untuk polipropilena dan kemudian menyusun matriks polipropilena dan serat jute menjadi lamina menggunakan metode hot-press.
Hasil uji tarik dan uji Heat Deflection Temperature memperlihatkan bahwa penambahan 40 wt% serat jute pada komposit polipropilena menaikkan kuat tarik sebesar 6% menjadi (38,2±4,9)MPa, modulus Young sebesar 50,2% menjadi (3,20±0,26)GPa dan suhu defleksi sebesar 143% menjadi (143,3±1,14)°C dibandingkan dengan PP murni. Hasil pengamatan dengan Scanning Electron Microscopy pada permukaan patahan diketahui bahwa mode kegagalan pada komposit adalah fiber pull-out. Dalam penelitian ini ditemukan bahwa komposit polipropilena diperkuat serat jute memiliki sifat mekanik yang tidak terlalu baik karena ikatan antarmuka serat-matriks yang tidak terlalu kuat "moda kegagalan fiber pull-out" menunjukan bahwa proses transfer beban dari matriks ke serat tidak terjadi dengan baik.

Jute is one of eco-friendly natural fiber with relatively low cost and high volume production. Polypropylene was selected as a matrix due to good specific properties and recyclable. This study aimed to determine the effect of weight fractions of jute fiber as an reinforcement in the polypropylene matrix to obtain an optimum weight fraction of jute fiber on composites. Jute fiber was pre-treated through alkalization. The polypropylene based reinforced jute fiber composite was initially produced by extrusion process for the polypropylene, followed by fabricated the composites by compiling a polypropylene matrix and jute fiber into lamina using a hot-press methods.
The results of tensile test and heat deflection Temperature test showed that the addition of 40 wt% jute fiber to polypropylene composites increased the tensile strength about 6% up to (38.2±4.9)MPa, the Young modulus about 50.2% up to (3.20±0.26)Gpa, and the deflection temperature about 143% up to (143.3±1.14)°C compared to pure PP. Based on the observation on the fracture surfaces by Scanning Electron Microscopy, it was shown that the mode of failure on the composites failure surfaces are "fiber pull-out". It was found that the tensile properties of the jute fiber reinforced polypropylene composites were not very good due to the weak interface bond between the fiber and the matrix, the "fiber pull-out" failure, indicated that the load from matrix to fiber was not well transfered.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2016
S63069
UI - Skripsi Membership  Universitas Indonesia Library
cover
Siti Lara Ollivia
"Penggunaan serat sintetis sebagai penguat pada komposit memiliki kekurangan yaitu tidak ramah lingkungan. Serat alam dapat digunakan sebagai alternatif penguat pada komposit. Polipropilena dan serat kenaf masing-masing digunakan sebagai matriks dan penguat pada komposit. Tujuan penelitian ini adalah untuk memperoleh sifat tarik dan suhu defleksi optimum dengan memvariasikan fraksi berat serat. Komposit polipropilena/serat kenaf difabrikasi dengan metode hot press. Serat kenaf diberi perlakuan alkali dalam larutan NaOH sebelum dijadikan penguat dan polipropilena diekstrusi sebelum digunakan sebagai matriks. Fraksi berat serat yang digunakan adalah 20 wt%, 30 wt%, 40 wt%, 60 wt% dan polipropilena murni sebagai pembanding. Pengujian yang dilakukan adalah uji tarik dan uji Heat Deflection Temperature (HDT) untuk mengetahui sifat mekanik dan sifat termal komposit. Nilai kuat tarik optimum berada pada komposit dengan komposisi serat 40 wt% dan mengalami kenaikan 80% dibandingkan dengan polipropilena murni yaitu sebesar (60,3 ± 4,3) MPa. Suhu defleksi optimum berada pada komposit dengan komposisi serat 40 wt% dan mengalami kenaikan hingga 170% dibandingkan dengan polipropilena murni yaitu sebesar (159,1 ± 1,8) ºC. Hasil pengamatan Scanning Electron Microscope pada komposit dengan fraksi berat 40 wt% menunjukkan ikatan antarmuka antara serat dan matriks yang relatif baik dan moda kegagalan berupa serat patah dan kegagalan matriks.

The use of synthetic fibers as reinforcement in composites has disadvantage which are not environmentally friendly. An alternative reinforcement for composites is natural fiber. Polypropylene and Sumberejo kenaf fibers are used respectively as the matrix and reinforcement. The aim of this research was to obtain the optimum tensile properties and deflection temperature with the variation of fiber fractions. Polypropylene/kenaf fiber composites fabricated by hot press method. The kenaf fiber was soaked in NaOH solution before being used as the reinforcement and polypropylene was extruded before being used as the matrix. The weight fractions of the fiber used were 20 wt%, 30 wt%, 40 wt% and 60 wt% to produce composites and pure polypropylene samples were also prepared for comparison. The optimum tensile strength and deflection temperature were found in the composites with the 40 wt% fiber fraction each with an increase up to 80% and 170% compared to the pure polypropylene with the result (60.3 ± 4,3) MPa and (159.1 ± 1,8) °C respectively. The result of Scanning Electron Microscope observation in a composite with the 40 wt% fiber fraction showed relatively good bonding interface between fibers and the matrix and the failure modes were fiber breakage and matrix failures.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2016
S62966
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rana Hafizhah
"Komposit ramah lingkungan telah berkembang dalam empat dekade terakhir karena kebutuhan terhadap material ramah lingkungan meningkat. Salah satu komposit ramah lingkungan adalah penggunaan serat alam sebagai penguat pada komposit. Indonesia memiliki berbagai macam serat alam, salah satunya serat daun nanas. Penelitian ini bertujuan untuk mengetahui pengaruh kandungan serat daun nanas, yang berasal dari Subang, pada sifat tarik dan suhu defleksi komposit polipropilena/serat daun nanas Subang. Serat daun nanas diberi perlakuan awal alkalisasi, sedangkan butiran polipropilena sebagai matriks diekstrusi menjadi bentuk lembaran. Metode pembuatan komposit yang digunakan adalah metode Hot Press.
Hasil uji tarik dan uji Heat Deflection Temperature menunjukkan komposit dengan fraksi berat serat daun nanas 30 wt.% adalah yang terbaik. Nilai nilai kuat tarik, modulus elastisitas an suhu defleksi masing-masing sebesar (64,04 ± 3,91) MPa; (3,976 ± 3,91) GPa dan (156,05 ± 1,77) °C, dengan kenaikan masing-masing 187,36%, 198,60%, 264,72% dibandingkan dengan polipropilena murni. Hasil pengamatan pada permukaan patahan menunjukkan moda kegagalan yaitu serat patah dan kegagalan matriks.

The development of eco-friendly composites has been increasing in the past four decades because the requirement of eco-friendly materials has been increasing. Indonesia has a lot of natural fiber resources and, pineapple leaf fiber is one of those fibers. This experiment aimed to determine the influence of weight fraction of pineapple leaf fibers, that were grown at Subang, to the tensile properties and the deflection temperature of polypropylene/Subang pineapple leaf fibers composites. Pineapple leaf fibers were pretreated by alkalization, while polypropylene pellets, as the matrix, were extruded into sheets. Hot press method was used to fabricate the composites.
The results of the tensile test and Heat Deflection Temperature (HDT) test showed that the composites that contained of 30 wt.% pineapple leaf fiber was the best composite. The values of tensile strength, modulus of elasticity and deflection temperature were (64,04 ± 3,91) MPa; (3,976 ± 3,91) GPa and (156,05 ± 1,77) °C respectively, in which increased 187,36%, 198,60%, 264,72% respectively from the pure polypropylene. The results of the observation on the fracture surfaces showed that the failure modes were fiber breakage and matrix failure.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2016
S64069
UI - Skripsi Membership  Universitas Indonesia Library
cover
Priska Gumilar
"ABSTRAK
Bambu sebagai salah satu serat alam yang ada di Indonesia berpotensi menjadi penguat pada komposit yang ramah lingkungan. Penelitian ini dilakukan untuk menentukan jenis komposit dan kuat lengkung dari komposit polipropilena/serat Bambu Tali (PP/SBT) sesuai dengan SNI 01-4449-2006 untuk papan serat dan kekeraannya. Serat Bambu Tali diberi perlakuan alkali sebelum dijadikan penguat komposit. Single Fiber Test dan analisa FTIR dilakukan pada serat Bambu Tali sebelum dan sesudah proses alkalisasi. Fabrikasi komposit menggunakan mesin ekstruder dengan variasi fraksi berat serat Bambu Tali 10wt%, 20wt%, dan 30wt%, dengan ukuran serat 0.5 mm. Uji lengkung dan kekerasan dilakukan pada komposit dan polipropilena murni, dan pengamatan Scanning Electron Microscope (SEM) dilakukan pada permukaan patahan uji lengkung. Hasil uji lengkung dan densitas menunjukkan bahwa komposit PP/SBT merupakan tipe Papan Serat Kerapatan Tinggi (PSKT) T1, dengan modulus lengkung dan kuat lengkung terbaik pada PP/SBT 30wt% masing-masing yaitu (79,01±4,47) GPa dan (36,97±3,03) MPa. Nilai ini meningkat 15,5% dan 25,6% dari polipropilena murni. Nilai uji kekerasan terbaik pada komposit PP/SBT 30wt% yaitu (61,86±0,67) HD yang meningkat 26% dari nilai kekerasan polipropilena murni. Hasil pengamatan SEM terlihat patahan serat terjadi pada permukaan patahan uji lengkung.

ABSTRACT
Bamboo as one of the natural fibers in Indonesia has the potential to become an environmental friendly composite reinforcement. This study was conducted to determine the density of composite and bending properties of polypropylene/Tali Bamboo fiber (PP/TBF) composites in accordance with SNI 01-4449-2006 for fiberboard and their hardness. Tali Bamboo Fiber was treated with alkali before being fabricated. Single Fiber Test and FTIR analysis were conducted on Tali Bamboo fibers before and after the alkalization process. Composites were fabricated using an extruder machine with variations in the weight fraction of Tali Bamboo fiber i.e 10wt%, 20wt%, and 30wt%, with a fiber size of 0.5 mm. Bending and hardness tests were carried for composites and pristine polypropylene ; fracture surfaces after bending test were ensured using Scanning Electron Microscope (SEM). The density and bending test results showed that all PP/TBF composites were categorized as Papan Serat Kerapatan Tinggi (PSKT) T1 type. PP/TBF30 composites had the highest bending modulus and strength of (79.01±4.47) GPa and (36.97±3.03) MPa respectively. These values increased 15.5% and 25.6% compared to the pristine polypropylene. The highest hardness value belong to PP/TBF30 i.e (61,86±0.67) HD, in which increased 26% from the value of pristine polypropylene hardness. SEM observations showed that fiber failure occurred on the fracture surfaces after bending test.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Soekartawi
Jakarta: UI-Press, 1989
338.173 SOE k
Buku Teks SO  Universitas Indonesia Library
cover
Anisa Padma Firdausi
"komposit berpenguat serat alam dapat menjadi alternatif untuk menggantikan komposit berpenguat serat sintetis yang kurang ramah terhadap lingkungan. Serat dari tumbuhan kenaf adalah salah satu serat alam yang dapat dimanfaatkan sebagai pengganti penguat serat sintesis pada komposit. Tujuan dari penelitian ini adalah untuk mengetahui kuat lentur, daya serap air, dan kadar air pada komposit polipropilena berpenguat serat kenaf dengan variasi fraksi berat serat sesuai dengan SNI 01-4449-2006. Serat kenaf diberi perlakuan alkali sebelum digunakan sebagai penguat dengan cara direndam dalam larutan NaOH 5%. Komposit polipropilena/serat kenaf kemudian difabrikasi dengan mesin hot press. Fraksi berat serat yang digunakan pada penelitian adalah 30 wt%, 40 wt%, 50 wt%, dan sampel polipropilena murni juga difabrikasi sebagai pembanding. Komposit yang difabrikasi disebut sebagai papan serat dengan kerapatan tinggi menurut SNI karena memiliki nilai densitas 1,08 g/cc. Kuat lentur, daya serap air, dan kadar air terbaik dimiliki oleh komposit polipropilena/serat kenaf 30wt% dengan nilai masing-masing (4,77 ± 1,00) MPa, (3,61 ± 1,77) % dan (1,12 ± 0,34)%; dan nilai-nilai ini memenuhi Standard Nasional Indonesia (SNI) tentang papan serat.

Natural fiber reinforced composites can be an alternative to replace composites with synthetic fibers reinforcement that are less environmentally friendly. Kenaf fiber which is obtained from kenaf plant is one of natural fibers that can be used as a reinforcement in composites. The purpose of this research was to determine the flexural strength, water absorbent, and water content of polypropylene/kenaf fiber composites with variations of fiber weight fraction according to SNI 01-4449-2006. Kenaf fiber was treated by alkaline treatment before being used as a reinforcement by immersing kenaf fiver in NaOH 5% solution. Polypropylene/kenaf fiber composites were fabricated with compression moulding method using a hot press machine. Fiber weight fractions used in this research were 30 wt%, 40 wt%, 50 wt%, and pristine polypropylene samples were also fabricated as a comparison. Based on SNI, the fabricated composites was called Papan Serat Kerapatan Tinggi (PSKT) because the density value was 1,08 g/cc. The flexural strength, minimum water absorption and water content were found in polypropylene/kenaf fiber composite 30wt% with the value of (4,77 ± 1,00) MPa, (3,61 ± 1,77) % and (1,12 ± 0,34)% respectively and these values met the Fiber Board Indonesian National Standard (SNI).
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2018
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Johannes Chandra
"Beton sebagai material konstruksi dikenal getas (brittle) dan lemah terhadap tarik dibandingkan dengan material baja. Penelitian para ahli menunjukkan peningkatan daktilitas beton melalui penambahan serat pada material beton. Salah satu jenis serat yang sering digunakan adalah serat Polypropylene (PP), yang juga digunakan sebagai bahan dasar pembuatan gelas kemasan air mineral. Berangkat dari peningkatan jumlah limbah gelas plastik, maka penggunaannya sebagai material tambahan pada beton diharapkan dapat mengatasi permasalahan sampah perkotaan, dan dalam jangka panjang diharapkan dapat mengurangi biaya pembangunan rumah tinggal.
Tujuan penelitian ini adalah untuk mempelajari efektifitas penggunaan cacahan limbah plastik PP terhadap peningkatan kuat tarik dan kuat lentur beton normal (fc' = 25 MPa). Kadar cacahan PP yang ditambahkan pada beton normal adalah 0,90; 1,35; 1,80; 2,25; 2,70; 4,50; 6,30; 9,00; 18,00 dan 27,00 kg/m3 atau dalam volume fraksi adalah 0,10; 0,15 0,20 ; 0,25; 0.30; 0,50; 0,70; 1,00; 2,00 dan 3,00% untuk pengujian kuat tarik yang dilakukan pada benda uji umur 7 dan 28 hari, serta 0,90; 1,35; 1,80; 2,25; 2,70; 4,50; 6,30; dan 9,00 kg/m3 atau dalam volume fraksi adalah 0,10; 0,15 0,20 ; 0,25; 0.30; 0,50; 0,70 dan 1,00% untuk pengujian kuat lentur yang dilakukan pada benda uji umur 28 hari.
Percobaan pembebanan yang dilakukan meliputi pembebanan tarik belah, pembebanan lentur dan modulus elastisitas. Benda uji untuk pengujian tarikbelah dan modulus elastisitas adalah silinder dengan diameter 15 cm dan tinggi 30 cm, sedangkan benda uji percobaan pembebanan lentur adalah balok 10x10x55 cm3.
Metode yang digunakan dalam penelitian ini adalah metode eksperimental, dimana percobaan dilakukan untuk mendapatkan kumpulan data, yang kemudian akan dianalisa secara statistik kuantitatif dan kualitatif.. Metode Analisis Rancang Campur yang digunakan adalah Metode US. Bureau. Benda Uji dibuat di Laboratorium Bahan Departemen Sipil FTUI. Standar Uji yang digunakan baik untuk pengujian material dasar, beton muda dan beton yang sudah mengeras
mengacu pada Standar ASTM.
Penambahan jumlah cacahan plastik polypropylene pada kadar tertentu akan menurunkan workabilitas dari beton, hal ini ditunjukkan dengan penurunan slump beton seiring dengan peningkatan kadar cacahan.
Dari Hasil Pengujian didapat, penambahan cacahan plastik polypropylene secara umum tidak memiliki pengaruh yang berarti pada tegangan tarik beton normal. Peningkatan paling besar terjadi pada benda uji kadar 0,3% umur 7 hari, yaitu sebesar 10,989%; dengan tegangan tarik berkisar antara 0,456 - 0,648 √ ? ' c. Hal ini secara umum diakibatkan karena ikatan atau gaya adhesi antara cacahan dengan matriks beton lebih lemah dari gaya kohesi antara matriks beton itu sendiri. Hal ini dibuktikan dengan uji tarik belah, dimana cacahan plastik pada benda uji yang terbelah tidak putus akibat pembebanan, melainkan masih tersambung, sedangkan material.
Sedangkan Penambahan cacahan plastik polypropylene secara umum meningkatkan tegangan tarik lentur beton normal. Peningkatan paling besar terjadi pada benda uji kadar 0,7% umur 28 hari, yaitu sebesar 17,098%; dengan tegangan tarik lentur berkisar antara 0,853 - 1,056 √ ? & c.

Concrete as construction material is known brittle and possess relatively weak tensile strength, compared to steel material. Experiments done by the experts shows an improvement in ductility of concrete by adding fiber to concrete material. One of the fibers that often used is Polypropylene (PP) fiber, which also used as a raw material in mineral water plastic glass manufacture. The increase of
amount of plastic glass waste, gives an idea to use it as an addition material in concrete. It expects decrease the urban waste problem, and in long term, to reduce the cost to build a house.
The purpose of this experiment is to study the effect of usage of PP plastic waste in tensile and flexural strength of normal concrete with fc? 25 MPa. The amount of crushed PP added to normal concrete are 0,90; 1,35; 1,80; 2,25; 2,70; 4,50; 6,30; 9,00; 18,00 and 27,00 kg/m3 or in fraction volume are 0,10; 0,15 0,20 ; 0,25; 0.30; 0,50; 0,70; 1,00; 2,00 and 3,00% for tensile strentgh test which done in age 7 and 28 days, also 0,90; 1,35; 1,80; 2,25; 2,70; 4,50; 6,30; and 9,00 kg/m3 or in fraction volume are 0,10; 0,15 0,20 ; 0,25; 0.30; 0,50; 0,70 and 1,00% for flexural strentgh test which done in age 28 days.
The test is consist of splitting tensile test, flexural test and modulus elasticity test. The sample for tensile and modulus elasticity test is cylinder with 15 cm diameter and 30 cm height, as for the flexural test is beam with size 10x10x55 cm3.
In this experiment the experimental method will be used, where the experiment done to collect data, and the data will be analyzed quantitative and qualitative statistically. The Mix Design Method used is US. Bureau Method. The sample will be made in Material Laboratory, Civil Engineering Department, Faculty of Engineering, University of Indonesia. The Standard to test the constituent materials, fresh concrete and hard concrete is based on ASTM Method.
The addition of crushed polypropylene plastic in specific amount will decrease the workability of concrete, shown by the decrease of concrete?s slump as the increase of crushed plastic amount.
The Test shows that the addition of crushed polypropylene plastic will not influence the tensile stress of normal concrete, generally. The highest increase happened in volume fraction 0.3% age 7 days, with 10.989%; and the tensile strengths have range from 0.456 - 0.648 √ ? & c. . This is generally because the bond or adhesion between the plastic and matrix is weaker then the cohesion of the matrix itself. It is proved by the splitting tensile test, where the plastics are do not yield by the loading, as for the aggregates are crushed by the loading.
As for the flexural tensile stress, it tends to increase. The highest increase, happened in volume fraction 0.7% age 28 days, with 17.098%; and the flexural strengths have range from 0.853 - 1.056 √ ? & c.
"
2008
S35339
UI - Skripsi Open  Universitas Indonesia Library
cover
Azmi Azis Novovic
"ABSTRAK
Dengan perkembangan yang pesat dalam dunia industri, penggunaan komposit yang berbasis polipropilen semakin banyak digunakan. Namun, penggunaan komposit berbasis polimer menyebabkan peningkatan jumlah polusi dikarenakan waktu penguraian polipropilen yang lama. Serat alam, salah satunya serat sorgum mulai dilirik untuk dijadikan penguat dalam komposit berbasis polipropilen untuk menciptakan suatu komposit yang ramah lingkungan. Masalah utama dalam proses ini adalah, perbedaan sifat kelarutan yang tinggi antara serat sorgum dan Polipropilen. Metode alkalinasi-termal dipilih dalam proses preparasi serat untuk menciptakan serat yang aman bagi lingkungan dan memiliki kompatibilitas tinggi dengan polipropilen. Dalam penelitian ini akan dilihat pengaruh dari waktu pencampuran dan temperatur dalam proses pencampuran Polipropilen dengan serat sorgum. Pada penelitian ini akan dikaji sifat mekanik dan morfologi dari komposit yang terbentuk dan mencari waktu dan temperatur pencampuran yang optimum. Variasi waktu pencampuran dalam penilitian ini adalah 5 menit, 7,5 menit dan 10 menit. Sedangkan variasi temperatur proses adalah 160°C, 170°C dan 180°C. Pada penelitian didapatkan Waktu dan temperatur pencampuran yang optimum adalah 170°C selama 10 menit dengan nilai kekuatan tarik 22,77 MPa. Dimana bentuk morfologi pada produk komposit tersebut juga lebih bagus dibandingkan variabel lainnya karena sedikitnya fenomena fiber pull-out dan void yang terjadi pada produk komposit tersebut dibandingkan variabel lainnya.

ABSTRACT
With the rapid development in the industrial world, the use of polypropylene-based composites is increasingly being used. However, the use of polymer-based composites causes an increase in the amount of pollution due to the long decomposition time of polypropylene. Natural fibers, one of which is sorghum fiber, is starting to be used as an amplifier in polypropylene-based composites to create an environmentally friendly composite. The main problem in this process is the difference in the high solubility between sorghum and polypropylene fibers. The thermal-alkalination method was chosen in the fiber preparation process to create fibers that are environmentally safe and have high compatibility with polypropylene. In this study, the effect of mixing time and temperature on the mixing process of Polypropylene with sorghum fiber will be seen. In this study the mechanical and morphological properties of the composites will be examined and find the optimum mixing time and temperature. The variation of mixing time in this study is 5 minutes, 7.5 minutes and 10 minutes. While the process temperature variations are 160°C, 170°C and 180°C. In this study, the optimum mixing time and temperature was 170°C for 10 minutes with a tensile strength of 22.77 MPa. Where the morphology of composite products is also better than other variables due to the small number of fiber pull-out phenomena and voids that occur in these composite products compared to other variables."
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Laurentius Calvin
"Plastik merupakan material yang mengalami perkembangan pesat 30 tahun terakhir ini. Namun sifatnya yang kurang kuat untuk aplikasi tertentu mengharuskan plastik dibuat menjadi komposit. Berbagai penguat sintetis tersedia seperti serat kaca namun harga serat kaca yang mahal dan sifatnya yang tidak ramah lingkungan membuat penggunaan material yang lebih murah dan ramah lingkungan sangat digencarkan. Komposit matriks polimer dengan penguat serat alam atau natural fiber reinforced polymer composites (NFRPC), sering hanya disebut natural fiber composites (NFC) menjadi solusinya.
Dalam penelitian ini digunakan serat alam sorgum yang berasal dari dalam negeri dan bagian yang digunakan merupakan produk sampingan dari tanaman sorgum. Proses preparasi serat sorgum diperlukan untuk meningkatkan kompatibilitasnya dengan matriks polipropilen (PP). Alkalinisasi-termal menjadi metode yang dipakai dalam melakukan preparasi serat dan hasilnya setelah dilakukan proses ini serat memiliki mekanisme mechanical bonding (interlocking) dengan PP. Kemudian pengaruh temperatur pencampuran PP dan sorgum dengan variasi 160°C, 170°C, 180°C, serta komposisi serat dengan variasi 5%, 10%, dan 15% dipelajari perilaku mekanis dan morfologinya. Hasil yang didapatkan variasi yang optimum yaitu pada temperatur pencampuran 170°C dan komposisi serat 15% memiliki kekuatan tarik mencapai 20,2 MPa dan modulus elastis 547 MPa serta temperatur pencampuran 170°C dan komposisi serat 5% memiliki elongasi 36,4 MPa.

Plastic is a material that has experienced rapid development in the last 30 years. But its nature is less strong for certain applications, requiring plastic to be made into composites. Various synthetic reinforcements are available such as glass fiber but the expensive price of glass fiber and its environmentally unfriendly nature making the usage of cheaper and environmentally friendly materials highly intensified. Polymer matrix composites with natural fiber reinforced polymer composites (NFRPC), often just called natural fiber composites (NFC), are the solution.
In this study, natural sorghum fibers originating from within the country were used and the used parts were by-products of sorghum plants. The preparation process of sorghum fibers is needed to improve its compatibility with the polypropylene (PP) matrix. Thermal-alkalinization is the method used in conducting fiber preparation and the results after this process the fibers have mechanical bonding (interlocking) mechanism with PP. Then the effect of PP and sorghum mixing temperature with variations of 160°C, 170°C, 180°C, and fiber composition with variations of 5%, 10%, and 15% on mechanical and morphological behavior were studied. The optimum result is obtained at mixing temperature of 170°C and 15% fiber composition that have tensile strength reaching 20,2 MPa and elastic modulus of 547 MPa also at mixing temperature of 170°C and 5% fiber composition have elongation of 36,4%.
"
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Enrico Susanto
"[Pada penelitian ini, serat ijuk dihancurkan dan diayak ukuran 40 # setelah itu serat ijuk diberi perlakuan kimia dengan NaOH 2 % selama 1 jam, KMnO4 0,1 N selama 15 menit, dan NaClO 5 % selama 5 jam dengan tujuan mendapatkan selulosa kristalin. Setelah itu dilakukan proses pencampuran kering (hotmelt mixing) antara polipropilen dengan serat ijuk hasil perlakuan kimia dengan 7,5 % volum serat ijuk terhadap polipropilen dengan variabel temperatur 160°C, 165°C, dan 170°C dan variabel waktu pencampuran 15 menit dan 20 menit. Setelah itu dilakukan pengujian uji FTIR buat serat, sedangan buat komposit adalah uji tarik, uji STA, uji XRD, dan uji FE-SEM hal ini dilakukan untuk mendapatkan sifat kristalinitas dan mekanik dari komposit polipropilen ini. Hasil penelitian menunjukkan bahwa serat ijuk hasil perlakuaan lebih kristalin dari pada serat ijuk tanpa perlakukan, polipropilen dengan serat ijuk hasil perlakuaan kimia cukup kompatibel terhadap polipropilen, dari penelitian didapatkan sifat kristalinitas terbaik pada variabel 165°C selama 20 menit. Dan yang memiliki sifat kekuatan tarik paling baik adalah variabel 170°C selama 20 menit, sedangkan yang memiliki % elongasi paling baik adalah dengan variabel 160°C 20 menit.

In this work, palm fiber crushed and sieved size 40 # after the palm fiber chemically treated with 2% NaOH for 1 hour, 0.1 N KMnO4 for 15 minutes, and 5% NaClO for 5 hours in order to obtain crystalline cellulose. Once that is done the dry mixing (hotmelt mixing) between polypropylene and palm fiber chemical treatment results with 7.5% volume of the palm fiber and polypropylene with a variable temperature of 160°C, 165°C and 170°C and a variable time mixing 15 minutes and 20 minutes. After it was examined FTIR test for fiber, while the composite is made tensile test, STA test, XRD test and FE-SEM test this is done to obtain crystallinity and mechanical properties of polypropylene composites this. The results show that fiber perlakuaan results more crystalline fibers than untreated palm fiber, polypropylene and palm fiber chemistry results treatment compatible enough to polypropylene, crystallinity of the research showed the best properties on the variable 165 ° C for 20 minutes. And who has the most excellent tensile strength properties are variable 170 ° C for 20 minutes, while the best of % elongation is at a variable 160 ° C 20 minutes.;In this work, palm fiber crushed and sieved size 40 # after the palm fiber chemically treated with 2% NaOH for 1 hour, 0.1 N KMnO4 for 15 minutes, and 5% NaClO for 5 hours in order to obtain crystalline cellulose. Once that is done the dry mixing (hotmelt mixing) between polypropylene and palm fiber chemical treatment results with 7.5% volume of the palm fiber and polypropylene with a variable temperature of 160°C, 165°C and 170°C and a variable time mixing 15 minutes and 20 minutes. After it was examined FTIR test for fiber, while the composite is made tensile test, STA test, XRD test and FE-SEM test this is done to obtain crystallinity and mechanical properties of polypropylene composites this. The results show that fiber perlakuaan results more crystalline fibers than untreated palm fiber, polypropylene and palm fiber chemistry results treatment compatible enough to polypropylene, crystallinity of the research showed the best properties on the variable 165 ° C for 20 minutes. And who has the most excellent tensile strength properties are variable 170 ° C for 20 minutes, while the best of % elongation is at a variable 160 ° C 20 minutes.;In this work, palm fiber crushed and sieved size 40 # after the palm fiber chemically treated with 2% NaOH for 1 hour, 0.1 N KMnO4 for 15 minutes, and 5% NaClO for 5 hours in order to obtain crystalline cellulose. Once that is done the dry mixing (hotmelt mixing) between polypropylene and palm fiber chemical treatment results with 7.5% volume of the palm fiber and polypropylene with a variable temperature of 160°C, 165°C and 170°C and a variable time mixing 15 minutes and 20 minutes. After it was examined FTIR test for fiber, while the composite is made tensile test, STA test, XRD test and FE-SEM test this is done to obtain crystallinity and mechanical properties of polypropylene composites this. The results show that fiber perlakuaan results more crystalline fibers than untreated palm fiber, polypropylene and palm fiber chemistry results treatment compatible enough to polypropylene, crystallinity of the research showed the best properties on the variable 165 ° C for 20 minutes. And who has the most excellent tensile strength properties are variable 170 ° C for 20 minutes, while the best of % elongation is at a variable 160 ° C 20 minutes.;In this work, palm fiber crushed and sieved size 40 # after the palm fiber chemically treated with 2% NaOH for 1 hour, 0.1 N KMnO4 for 15 minutes, and 5% NaClO for 5 hours in order to obtain crystalline cellulose. Once that is done the dry mixing (hotmelt mixing) between polypropylene and palm fiber chemical treatment results with 7.5% volume of the palm fiber and polypropylene with a variable temperature of 160°C, 165°C and 170°C and a variable time mixing 15 minutes and 20 minutes. After it was examined FTIR test for fiber, while the composite is made tensile test, STA test, XRD test and FE-SEM test this is done to obtain crystallinity and mechanical properties of polypropylene composites this. The results show that fiber perlakuaan results more crystalline fibers than untreated palm fiber, polypropylene and palm fiber chemistry results treatment compatible enough to polypropylene, crystallinity of the research showed the best properties on the variable 165 ° C for 20 minutes. And who has the most excellent tensile strength properties are variable 170 ° C for 20 minutes, while the best of % elongation is at a variable 160 ° C 20 minutes.;In this work, palm fiber crushed and sieved size 40 # after the palm fiber chemically treated with 2% NaOH for 1 hour, 0.1 N KMnO4 for 15 minutes, and 5% NaClO for 5 hours in order to obtain crystalline cellulose. Once that is done the dry mixing (hotmelt mixing) between polypropylene and palm fiber chemical treatment results with 7.5% volume of the palm fiber and polypropylene with a variable temperature of 160°C, 165°C and 170°C and a variable time mixing 15 minutes and 20 minutes. After it was examined FTIR test for fiber, while the composite is made tensile test, STA test, XRD test and FE-SEM test this is done to obtain crystallinity and mechanical properties of polypropylene composites this. The results show that fiber perlakuaan results more crystalline fibers than untreated palm fiber, polypropylene and palm fiber chemistry results treatment compatible enough to polypropylene, crystallinity of the research showed the best properties on the variable 165 ° C for 20 minutes. And who has the most excellent tensile strength properties are variable 170 ° C for 20 minutes, while the best of % elongation is at a variable 160 ° C 20 minutes., In this work, palm fiber crushed and sieved size 40 # after the palm fiber chemically treated with 2% NaOH for 1 hour, 0.1 N KMnO4 for 15 minutes, and 5% NaClO for 5 hours in order to obtain crystalline cellulose. Once that is done the dry mixing (hotmelt mixing) between polypropylene and palm fiber chemical treatment results with 7.5% volume of the palm fiber and polypropylene with a variable temperature of 160°C, 165°C and 170°C and a variable time mixing 15 minutes and 20 minutes. After it was examined FTIR test for fiber, while the composite is made tensile test, STA test, XRD test and FE-SEM test this is done to obtain crystallinity and mechanical properties of polypropylene composites this. The results show that fiber perlakuaan results more crystalline fibers than untreated palm fiber, polypropylene and palm fiber chemistry results treatment compatible enough to polypropylene, crystallinity of the research showed the best properties on the variable 165 ° C for 20 minutes. And who has the most excellent tensile strength properties are variable 170 ° C for 20 minutes, while the best of % elongation is at a variable 160 ° C 20 minutes.]"
Depok: Fakultas Teknik Universitas Indonesia, 2015
S1575
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>