Hasil Pencarian  ::  Simpan CSV :: Kembali

"ABSTRAKPengembangan plastik yang mudah terdekomposisi saat ini sudah banyak di lakukan, terutama dengan menggunakan bahan dasar polimer seperti poly(vinyl alcohol) yang dimodifikasi menjadi komposit. Bio-nanokomposit dibuat dengan metoda solvent casting dari poly(vinyl alcohol) sebagai matriks dan organoclay sebagai nanofiller. Penelitian ini bertujuan mempelajari karakteristik dan sifat mekanik material nanokomposit poly(vinyl alcohol) / organoclay terinterkalasi heksadesiltrimetilamonium bromida (C16). Penelitian ini dilakukan melalui dua tahap yaitu pembuatan organoclay dengan C16; serta sintesis dan karakterisasi nanokomposit poly(vinyl alcohol) / organoclay ? C16. Proses interkalasi terlihat dari pergeseran puncak bentonite dan organoclay yaitu dari 2θ = 6o ke 2θ = 4,9o, dengan nilai basal spacing dari 15,1 Å menjadi 19,7 Å. Kuat tarik tertinggi dimiliki oleh poly(vinyl alcohol) murni dengan nilai 58,02 MPa dan terendah pada nanokomposit poly(vinyl alcohol) / organoclay ? C16 7% dengan nilai 41,33 MPa. Laju transmisi uap air tertinggi dimiliki oleh nanokomposit poly(vinyl alcohol) / organoclay ? C16 7% dengan nilai 0,35 gr/m2/jam dan terendah pada poly(vinyl alcohol) murni dengan nilai 0,62 gr/m2/jam. Nanokomposit poly(vinyl alcohol) / organoclay ? C16 3% memiliki sifat dekomposisi paling baik dan dan sifat dekomposisi yang paling rendah yaitu pada poly(vinyl alcohol) murni.

---

ABSTRACTEasy decomposed plastic development is now being popular, especially with polymer based material such as modified poly(vinyl alcohol) into composites. The bio-nanocomposite made by solvent casting method of poly(vinyl alcohol) as matrix and organoclay as nanofilter. This research aims to study the characteristics and mechanical properties of nanocomposite poly(vinyl alcohol) / hexadecyltrimethylammonium bromide (C16) intercalated organoclay. This study was conducted in two stages, the process of organoclay with C16; as well as the synthesis and characterization of nanocomposite poly(vinyl alcohol) / organoclay - C16. Intercalation process can be seen from the peak shift of bentonite and organoclay that 2θ = 6 ° to 2θ = 4.9 °, with a basal spacing of 15.1 Å to 19.7 Å. The highest tensile strength possessed by pure poly(vinyl alcohol) with a value of 58.02 MPa and the lowest is in the nanocomposite poly(vinyl alcohol) / organoclay - C16 7% by value 41.33 MPa. The highest water vapor transmission rate is owned by nanocomposite poly(vinyl alcohol) / organoclay - C16 7% with a value of 0.35 g/m2/h and the lowest is in the pure poly(vinyl alcohol) with a value of 0.62 g/m2/hr. Nanocomposite poly(vinyl alcohol) / organoclay - C16 3% has the nicest also the most low decomposition propertie, and the nature decomposition is on pure poly(vinylalcohol).;;;"

"Organoclay adalah lempung yang disintesis dengan bahan organik ODTMABr tanpa mengubah struktur kimianya. Pergeseran puncak (001) difaktogram menunjukkan bahwa ODTMABr berhasil masuk ke dalam lapisan lempung. Basal spacing pada organoclay lebih besar dibandingkan dengan basal spacing bentonit. Uji FTIR menunjukkan bahwa organoclay Tapanuli (OCT-C18) terinterkalasi oleh surfaktan ODTMABr. Sintesis antara Polyvinyl Alcohol (PVA) dan OCT dalam jumlah sedikit yaitu PVA/OCT-C18 5% atau kurang menghasilkan nanokomposit berstruktur eksfoliasi. Penambahan OCT-C18 memberi peningkatan kekuatan mekanik dan modulus elastisitas PVA/OCT-C18, tetapi memberi penurunan regangan pada PVA/OCT-C18 7%. Hasil SEM pada permukaan patahan menunjukkan peningkatan kekuatan mekanik dan teramatinya peningkatan kekasaran permukaan patahan. Banyak dan besar rongga pada PVA/OCT-C18 mempengaruhi kekuatan mekanik PVA/OCT-C18.

---

Organoclay was synthesized using ODTMABr surfactant without changing its chemical structure. The diffractogram showed that the (001) peak shifted and this indicated that the organoclay layers were intercalacted. The basal spacing of organoclay which was higher than of bentonite. The FTIR results indicated the ODTMABr surfactant intercalated the clay layers. Synthesis of Polyvinyl Alcohol (PVA) and small amounts of OCT-C18 less than 5% wt, produced exfoliated nanocomposite structure. The addition of OCT-C18 improved mechanical strength and modulus of elasticity, but it decreased the value of strain of PVA/OCT-C18 composites. SEM observation results on the fracture surface showed that the enchanted of mechanical strength of PVA/OCT-C18 followed by the roughness of fracture surface. The number of voids or cavities on PVA/OCTC18 affected the mechanical strength of PVA/OCT-C18."

"Film nanokomposit polimer biodegradable telah dibuat. Clay Tapanuli termodifikasi heksadesiltrimetilamonium bromida (C16) dan oktadesiltrimetilamonium bromida (C18) digunakan sebagai nanofiller. Penelitian ini terdiri atas pemurnian clay, sintesis organoclay dan pembuatan film nanokomposit dengan metode solvent casting. Penelitian ini untuk mempelajari pengaruh jumlah organoclay dan panjang rantai alkil surfaktan terhadap sifat mekanik bahan bionanokomposit. Pergeseran puncak d001 pada difraktogram menunjukkan kenaikan basal spacing sebesar 0,35 nm dan 0,48 nm masingmasing oleh surfaktan C16 dan C18. Difraktogram XRD nanokomposit selulosa asetat dan poli(vinil alkohol) juga menunjukkan adanya struktur dispersi campuran interkalasi dan eksfoliasi. Hasil ini mendukung hasil uji mekanik film nanokomposit dimana kuat tarik dan modulus elastisitas meningkat. Hasil uji tarik film nanokomposit menunjukkan adanya pengaruh penambahan organoclay dan panjang rantai alkil surfaktan terhadap perubahan nilai kuat tarik, modulus tarikdan regangansaatpatah film nanokomposit dimana peningkatan sifat mekanik nanokomposit selulosa asetat lebih tingi dibandingkan nanokomposit poli(vinilalkohol). Citra FE-SEM film nanokomposit pada permukaan patahan memperlihatkan pori-pori yang tidak teratur dan elastisitas film nanokomposit poli(vinilalkohol) yang lebih panjang dibandingkan film nanokomposit selulosa asetat.

---

Nanocomposite films of biodegradable polymers were prepared. The Tapanuly clay modified by heksadecyltrimethylammonium bromide (C16) and Octadecyltrimethylammonium bromide (C18) were used as nanofillers. This experiment were consisted of namely clay purification, organoclay synthesis, and nanocomposite film preparation by a solvent casting methode. The aim of this work was to study the effect of organoclay content and the surfactant alkyl chain length to the mechanical properties of bionanocomposite materials. The shifting of d001 peaks on the difractogram showed that the basal spacing increased by 0.35 nm and 0.48 nm by C16 and C18 surfactants respectively. The XRD difraction also showed the results of cellulose acetate nanocomposite and poly(vinyl alcohol) nanocomposite had a mixed structure of intercalated and exfoliated structure.

These results supported the mechanical testing results of the nanocomposite films that of the tensile strentgh and modulus elasticity was enhanced. The mechanical testing result showed that the organoclay content and surfactant alkyl chain length influenced the tensile strength, modulus elasticity, and strain at break of the nanocomposite films that of the increasing of cellulose acetate nanocomposite mechanical properties was higher than poly(vinyl alcohol) nanocomposite. FESEM images on the fracture surface of the nanocomposite films showed irregular pores on the cellulose acetate nanocomposite films and the longer elasticity of poly(vinyl alcohol) nanocomposite compared to the cellulose acetate nanocomposite films."

"Sintesis membran nanokomposit PVA-Organoclay Tapanuli dilakukan dengan tahap sintesis organoclay Tapanuli dan sintesis nanokomposit PVAOrganoclay Tapanuli. Sintesis organoclay Tapanuli dilakukan dengan menginterkalasikan surfaktan HDTMABr ke dalam gallery clay melalui tahapan purifikasi, sintesis Na-MMT dan sintesis Organoclay Tapanuli, sedangkan pembuatan membran komposit melalui proses solvent casting. Pengaruh interkalasi surfaktan diamati dengan XRD dan FTIR. Dari karakterisasi XRD, diketahui bahwa interkalasi surfaktan ke dalam gallery clay meningkatkan nilai basal spacing organoclay Tapanuli dari 15.96 Å menjadi 18.81 Å. Nanokomposit dibuat dari PVA sebagai matriks dan organoclay Tapanuli - HDTMABr sebagai nanofiller. Karakterisasi yang dilakukan adalah XRD, FTIR, SEM, dan uji tarik. Dari hasil uji tarik diperoleh pada komposisi 3 wt % organoclay Tapanuli-HDTMABr merupakan hasil yang terbaik. Hal ini dibuktikan dengan nilai modulus tarik dan nilai kuat tarik yang paling tinggi dibandingkan dengan komposisi lainnya, dengan kenaikan masing-masing 162,3 % dan 13,55 %.

---

PVA - Organoclay Tapanuli nanocomposite membranes were syntesized through two steps, namely the organoclay Tapanuli intercalation process and the PVA - Organoclay Tapanuli nanocomposite syhthesis. The synthesis of organoclay Tapanuli was conducted by intercalating the HDTMABr surfactant into the clay gallery through purification, Na-MMT synthesis, and organoclay Tapanuli synthesis processes, while solvent casting technique was applied to produced the nanocmposite membranes. The effect of surfactant in the clay gallery was observed using XRD, and FTIR. The XRD results showed that, the surfactant was intercalate into the clay gallery and increased the basal spacing of organoclay Tapanuli from 15.96 Å to 18.81 Å. The nanocomposites were characterized using XRD, FTIR, and SEM, and tensile test was also carried out. The tensile test results showed that the 3 wt% organoclay Tapanuli - PVA was the best sample compared to other clay compositions. It was proved that the values of tensile modulus and tensile strength increased by 162,3 % and 13,55 % respectively."

"Meningkatnya limbah plastik di Indonesia menjadi salah satu masalah di Indonesia. Tujuan dari penelitian ini adalah membuat membran plastik nanokomposit yang memiliki kemampuan terdekomposisi di alam. Sintesis selulosa asetat murni dan nanokomposit SA/OCT-C16 dengan variasi komposisi organoclay 1 wt%, 3 wt%, 5 wt%, dan 7 wt% telah berhasil dibuat dengan metode solvent casting. Struktur bentonit tetap sama meskipun telah mengalami reaksi pertukaran kation hingga menjadi organoclay. Hal tersebut dapat dilihat dengan adanya pita serapan khas bentonit berupa deformasi SI-O-Si pada bilangan gelombang 500-400 cm-1 dan adanya pita serapan khas dari karbon CH2 yang berasal dari surfaktan heksadesiltrimetil amonium bromida (HDTMA-Br) pada bilangan gelombang 2930 cm-1 dan 2842 cm-1. Difraktogram organoclay menunjukkan peningkatan nilai basal spacing dari 15,19 Å menjadi 20,14 Å. Hasil uji tarik menunjukkan bahwa nanokomposit dengan komposisi organoclay 1 wt% memiliki kuat tarik tertinggi yaitu 44,56 MPa dengan kenaikan sebesar 16% dibandingkan dengan selulosa asetat murni. Hasil uji dekomposisi menunjukkan bahwa selulosa asetat mempunyai kemampuan terdekomposisi paling tinggi, yaitu sebanyak 37% sedangkan nanokomposit dengan 1 wt% organoclay terdekomposisi sebanyak 25% selama 60 hari penguburan. Secara umum massa terdekomposisi nanokomposit lebih tinggi daripada massa terdekomposisi plastik komersial.

---

This research is based on the increasing problem of plastic waste in Indonesia. The focus of this research is to produce a nanocomposite plastic membranes that have the ability to decompose in nature better than commercial plastic. Synthesis of cellulose acetate and nanocomposite SA/OCT-C16 with variation in composition of 1 wt%, 3 wt%, 5 wt%, and 7 wt% of organoclay has been successfully created with a solvent casting method. Bentonite structure remain visible although it has undergone a cation exchange reaction to be an organoclay.

It can be seen with their typical absorption bands of bentonite on the form of the deformation of the Si-O-Si at wave number 500-400 cm-1 and the typical absorption band of carbon CH2 derived surfactant hexadecyltrimethylammonium bromide (HDTMA-Br) at wave number 2930 cm-1 and 2842 cm-1. Difractogram on organoclay show the increase of the value of basal spacing of organoclay from 15,19 Å up to 20,14 Å.

The tensile strength test shows that nanocomposite with 1 wt% composition of organoclay has the graetest tensile strength that is equal 44.56 MPa with an increase of 16% compared to pure cellulose acetate. The result of decomposition test shows that pure cellulose acetate has the ability to decompose the highest, which is about 37% whereas nanocomposite with 1 wt% of organoclay only able to decompose as much as 25% during 60 days of burial. In general, the mass of decomposed nanocomposite is higher than the mass of commercial plastic decomposes."

"ABSTRAKPemanfaatan bentonit di Indonesia sebagai nanofiller masih belum optimal. Sintesis nanokomposit selulosa asetat (SA)/selulosa asetat butirat (SAB) dengan penguat organoclay bertujuan untuk mendapatkan plastik yang mudah terurai dengan sifat mekanik dan sifat fisis dari masing-masing komposit. Penelitian ini dilakukan melalui beberapa tahap yaitu preparasi bentonit, purifikasi karbonat, sintesis Na-Bentonit, sintesis organoclay-ODTMABr (OCT-C18) dan sintesis nanokomposit SA serta SA/SAB OCT-C18. Pengaruh terinterkalasi terlihat dari pergeseran puncak (001) difaktogram dengan kenaikan nilai basal spacing dari Na-Bentonit ke OCT yaitu 15,19 Å ke 21,69 Å. Kuat tarik tertinggi terjadi pada membran SA/5wt%SAB yaitu 24,34 MPa. Setelah dilakukan dekomposisi UV selama 24 jam, SA/1wt%OCT-C18 dan SA/5wt%SAB/ 7wt% OCT-C18 terdegradasi dengan kuat tarik masing-masing 22,03 MPa dan 9,87 MPa.

---

ABSTRACTThe utilization of bentonite as nanofiller in Indonesia is not optimum. Nanocomposite synthesis of cellulose acetate (CA) / cellulose acetate butyrate (CAB) with organoclay aims to get biodegradable plastics with mechanical and physical properties of each composite. This research was carried out in several stages, namely bentonite preparation, carbonate purification, Na-Bentonite synthesis, synthesis of organoclay-ODTMABr (OCT-C18), the synthesis of CA as well as CA / CAB OCT-C18 nanocomposites. Diffractogram showed that peak (001) shifted related to the increase of basal spacing from Na-Bentonite to the OCT is 15.19 Å to 21.69 Å. The highest tensile strength from the membrane CA/5wt%CAB which was 24,34 MPa. After 24 hours UV exposure, the CA/1wt%OCT-C18 and CA/5wt%CAB 7wt% OCT-C18 were degraded with each tensile strength of 22,03 MPa and 9,87 Mpa respectively."

"Serangkaian percobaan mengenai teknik pembentukan material polimer adhesive, yaitu Poli(vinil) asetat (PVAc) melalui tahapan-tahapan reaksi sintesis mengunakan teknik polimerisasi emulsi semi kontinu telah dilakukan. PVAc disintesis dari vinil asetat monomer (VAM) dengan Ammonium Peroxydisulphate (APS) sebagai inisiator dalam medium air dengan suhu reaksi dijaga pada 70 ± 5 °C dan kecepatan pengadukan masingmasing 300 rpm selama 4 jam waktu reaksi. Zat koloid pelindung berupa Poli(vinil) alkohol (PVOH) parsial hidrolisis, surfaktan anionik (SLS) dan surfaktan nonionik (NP- 10) ditambahkan untuk meningkatkan kinerja emulsi PVAc. Semua produk hasil sintesis belum memenuhi target yield teoretis berdasarkan pengukuran solid content dengan kadar residual monomer > 29%. Pengukuran pH dan konduktivitas dengan Hanna Instrument pada proses reaksi menunjukan semua produk memiliki pH akhir 2,8 dan konduktivitas > 700 μS. pengukuran kekentalan menggunakan Viscometer Ostwald menunjukan semua sampel memiliki nilai < 3 Cp. Pengukuran bobot jenis menggunakan Pycnometer menunjukan semua sampel memiliki nilai > 1.03 g/ml. Pembentukan polimer PVAc yang terbentuk berdasarkan gugus fungsi menggunakan FTIR menunjukan karakteristik molekul pada bilangan gelombang 3310-3444 cm-1, 2935 cm-1 dan 1756 cm-1. Pola pemutusan rantai yang khas dengan menganalisis komponen menggunakan GC-MS, didapatkan pola pemutusan pada m/z 86 dan 43.

---

A series of experiments on the technique of forming adhesive polymer materials, namely Poly(vinyl) Acetate/PVAc through stages of a synthesis reaction using a semicontinuous emulsion polymerization technique have been carried out. PVAc was synthesized from Vinyl Acetate Monomer (VAM) with Ammonium Peroxydisulphate (APS) as an initiator in water medium with the reaction temperature being maintained at 70 ± 5 °C and stirring speed of 300 rpm for 4 hours of reaction time. A protective colloid in the form of partial hydrolysis Poly(vinyl) Alcohol (PVOH), anionic surfactant (SLS) and nonionic surfactant (NP-10) was added to improve the performance of the PVAc emulsion. All synthesized products have not met the theoretical yield target based on solid content measurement with monomer residual content > 29%. Measurement of pH and conductivity using Hanna Instrument in the reaction process showed that all products had a final pH of 2,8 and conductivity > 700 μS. Viscosity measurement using the Ostwald Viscometer shows all samples have a value < 3 Cp. Measurement of specific gravity using a Pycnometer shows that all samples have a value > 1.03 g/ml. The formation of the PVAc based on structural characteristics in the form of functional groups using FTIR showed molecular characteristics shows at wavenumber of 3310-3444 cm-1, 2935 cm-1 and 1756 cm-1. A typical chain breaking pattern by analyzing the components using GCMS, the breaking patterns were obtained at m/z 86 and 43."

"Sintesis membran selulosa asetat dilakukan melalui dua tahap yang meliputi: sintesis organoclay dan sintesis membran. Sedangkan, sintesis organoclay terdiri dari tiga tahapan yaitu purifikasi karbonat, sintesis Na-Bentonit dan sintesis organoclay-ODTMABr. Na-Bentonit dengan kapasitas tukar kation (KTK) 48,749 meq/100 gram bentonit yang diinterkalasi dengan 1 KTK surfaktan ODTMABr menghasilkan Organoclay Terinterkalasi (OCT). Pengaruh interkalasi diamati oleh XRD low angle yang menunjukkan adanya kenaikan nilai basal spacing dari Na-Bentonit ke OCT, baik tanpa maupun dengan purifikasi karbonat, masing-masing dari 15,31 Å ke 20,07 Å dan 15,66 Å ke 19,94 Å. Selulosa asetat (CA) dimodifikasi dengan penambahan nanofiller organoclay-ODTMABr (OCT-C18) dengan metode solvent casting. Karakterisasi yang dilakukan adalah XRD, FTIR, SEM, dan EDX. Pengamatan pengaruh komposisi berat OCT-C18 yang ditambahkan ke dalam larutan selulosa asetat menunjukkan bahwa membran dengan komposisi 7% wt memiliki warna yang paling keruh, secara fisik terasa paling lentur, dan tidak mudah robek.

---

Synthesis of cellulose acetate membranes through two stages which include organoclay synthesis and membrane synthesis. Meanwhile, organoclay synthesis consists of three phases that include carbonate purification, synthesis of Na-Bentonite and organoclay-ODTMABr synthesis. Na-bentonite by cation exchange capacity (CEC) 48.749 meq/100 grams of bentonite which intercalated with 1 CEC ODTMABr surfactant produce organoclay intercalated (OCT). Effect of intercalation was observed by low angle XRD which shows an increase value of basal spacing of Na-Bentonite to OCT, either without or with carbonate purification, respectively from 15.31 Å to 20.07 Å and 15.66 Å to 19.94 Å Å. Cellulose acetate (CA) modified with adding organoclay-ODTMABr (OCT-C18) nanofillers with a solvent casting method. XRD, FTIR, SEM, and EDX characterization was performed. Parameters measured influence of weight percent of OCT-C18 is added to a solution of cellulose acetate. Membrane with a composition of 7 wt% has the most opaque colors, the highest physical resilient, and the strongest (not easily torn)."

"Membran selulosa asetat / organoclay-HDTMABr dibuat melalui dua tahap sintesis, yaitu sintesis organoclay dan sintesis membran. Sintesis organoclay meliputi tiga tahap, yaitu purifikasi karbonat, preparasi Na-Bentonit, dan sintesis organoclay-HDTMABr. Organoclay-HDTMABr disintesis menggunakan Na-Bentonit dan HDTMABr sebanyak 1 KTK dengan metode ultrasonik, dimana Na-Bentonit yang digunakan memiliki kapasitas tukar kation (KTK) sebesar 48,749 meq/100 gram bentonit. Pengujian XRD pada sampel organoclay menunjukkan interkalasi HDTMABr dapat meningkatkan basal spacing organoclay menjadi 18,80 Å dan 19,04 Å pada masing-masing sintesa dengan purifikasi dan tanpa purifikasi karbonat. Telah dilakukan variasi komposisi organoclay-HDTMABr 1 KTK (OCT-C16) yang ditambahkan pada biokomposit sebagai nanofiller. Hasil sintesis pada penelitian ini dikarakterisasi menggunakan FTIR. Dari kelima variasi komposisi OCT-C16 (0%, 1%, 3%, 5%, dan 7%) yang ditambahkan, variasi 7% OCT-C16 menghasilkan produk membran biokomposit yang paling keruh, paling lentur, dan tidak mudah robek.

---

Cellulose acetate / organoclay-HDTMABr membranes ware prepared ​​through two stages of synthesis, namely : the organoclay synthesis and membrane synthesis. Organoclay synthesis involved three stages : purification of carbonate, preparation of Na-bentonite, and synthesis of organoclay-HDTMABr. Organoclay-HDTMABr was synthesized with the amount of 1 CEC Na-Bentonite and HDTMABr using an ultrasonic method. The Na-Bentonite had a cation exchange capacity (CEC) of 48.749 meq/100 grams of bentonite. XRD measdurement result showed HDTMABr increased the basal spacing of organoclay to 18,80 Å and 19,04 Å for organoclay with carbonate purification and without carbonate purification respetively. The HDTMABr-organoclay (OCT-C16) was added to cellulose acetate as nanofiller with different compositions. The biocomposites obtained in this study, with the clay loading of 0%, 1%, 3%, 5%, and 7% were characterized by FTIR. It was observed that the addition of 7 % OCT-C16 into cellulose acetate membranes produced the most flexible, the most opaque, and most difficult torn membrane."

"Penilitian ini berfokus pada sintesis Polivinil Asetat (PVAc) emulsi dengan penambahan polivinil alkohol (PVA) sebagai agen pelindung koloid. Sintesis dilakukan dengan penambahan PVA menggunakan tiga jenis PVA terhidrolisis Sebagian yang dibedakan berdasarkan derajat polimerisasinya yaitu rendah, sedang, dan tinggi. Selama reaksi berlangsung sistem berada pada temperatur 70-800C, kecepatan agitator 300 rpm, dan menggunakan teknik semi-continuous selama 5 jam. Beberapa karakterisasi PVAc yang terukur sebagai parameter antara lain temperatur antara 67-770C, pH antara 6-1, densitas antara 1,19-1,2 g/mL, kandungan padatan yang memiliki rentang nilai 19,75-22,29 %, ukuran partikel antara 67,1-1310,5 nm, berat molekul 1307,4015-5226,3346 g/mol, viskositas antara 1,01-11,07 mPa.s. Efek penambahan PVA sebagai agen pelindung koloid akan memengaruhi nilai viskositas dari hasil akhir polimerisasi. Selain itu juga dapat memengaruhi kekuatan daya rekat pada sintesis polimerisasi.

---

This research focuses on the synthesis of polyvinyl acetate (PVAc) emulsion with the addition of polyvinyl alcohol (PVA) as a protective colloid agent. The synthesis was carried out by adding PVA using three types of partially hydrolyzed PVA which were distinguished by their degree of polymerization, i.e. low, medium, and high. During the reaction, the system was at a temperature of 70-800C, stirring 300 rpm, and used a semi-continuous technique for 5 hours. Characterizations of PVAc that are measured as parameters include temperature at 67-77⁰C, pH at 6-1, density at 1.19-1.2 g/mL, solids content which has a value range from 19.75-22.29%, particles size at 67.1-1310.5 nm, molecular weight at 1307.4015-5226.3346 g/mol, viscosity at 1.01-11.07 mPa.s. The effect of adding PVA as a protective colloid agent will affect the viscosity value of the final polymerization result. In addition, it can also affect the adhesive strength of the polymerization synthesis."