Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 96510 dokumen yang sesuai dengan query
cover
Satrio Wibowo
"Saat ini penggunaan material berbasis polimer semakin meningkat seiring dengan pertumbuhan populasi manusia. Kebutuhan akan material berbasis polimer tersebut didasari oleh harga yang relatif murah dan fungsinya serba guna. Polimer berbasis pada minyak bumi merupakan jenis polimer yang sulit untuk diuraikan oleh mikroorganisme sehingga dibutuhkan material polimer alternative yang berasal dari alam untuk mengatasi isu lingkungan tersebut. Poly Lactic Acid (PLA) merupakan salah satu polimer alam yang cukup banyak digunakan. Namun PLA memiliki sifat mekanik dan ketahanan termal yang kurang baik, sehingga dibutuhkan pengisi dari bahan alam seperti serat ijuk untuk meningkatkan sifat mekanik.
Pada penelitian ini dilakukan percobaan untuk mengetahui kompatibilitas pengisi dan matriks, konsentrasi optimal pemutihan serat, waktu optimal pemutihan serat dan komposisi optimal antara pengisi dan matriks. Pengamatan dilakukan terhadap morfologi permukaan serat ijuk dan fraktografi material komposit menggunakan FE-SEM, mengetahui perubahan kristalinitas serat ijuk menggunakan X-RD, mengetahui gugus fungsi dari serat ijuk untuk melihat kandungan lignin dan hemiselulosa menggunakan FTIR serta kekuatan tarik material komposit menggunakan micro-tensile.
Hasil dari penelitian ini yaitu pemutihan dapat meningkatkan kompatibilitas pengisi dan matriks, konsentrasi optimal pemutihan adalah 7,5% NaClO selama 2 jam dan waktu optimal pemutihan adalah 1 jam dengan 10% NaClO. Dengan penambahan komposisi ijuk 10%, 20%, 30% ke dalam matriks PLA maka kekuatan tarik material komposit semakin meningkat.

Nowadays, The necessity of polymer-based material is getting higher because of its versatile utilization and relatively low cost. Petroleum polymer is difficult to be processed by micro-organism so that the alternative natural polymer is required to tackel this issue. Poly Lactic Acid (PLA) is one of the polymer used in many industries but PLA has the poorness on its mechanical properties and thermal resistance. Therefore, the addition of reinforcement such as ijuk fiber can be used to optimize its properties.
In this research, the compability of reinforcement and matrix, the optimum concentration of bleaching, the time of bleaching and the composition of reinforcement and matrix are studied. Visual observation on the morfology and fractography of ijuk fiber surface was performed using FE-SEM, the crystallinity of ijuk fiber was conducted using XRD, the functional group of ijuk fiber was carried out using FTIR to examine lignin and hemi-cellulose content and the tensile test of this composite material was performed using micro-tensile test.
From the data, it was acquired that bleaching enhance the compability between filler and matrix, the optimum concentration of bleaching is 7,5% NaClO for 2 hours and the optimum time of bleaching is 1 hour with 10% NaClO. In the mechanical properties aspect, it is obtained that as the higher ijuk addition, from 10% to 30%, into the PLA matrix, the tensile strength of the composite is improve.
"
Depok: Fakultas Teknik Universitas Indonesia, 2015
S60812
UI - Skripsi Membership  Universitas Indonesia Library
cover
Aldo Zulfahmi Putra
"Urgensi akan permasalahan limbah makin meningkat. Salah satu limbah yang paling sulit di olah adalah limbah plastik, maka kebutuhan akan plastik yang dapat di degradasi secara cepat menjadi salah satu alternatif solusi untuk permasalahan tersebut. Material berbahan dasar organik seperti serat ijuk dan polylactic acid mulai di kembangkan. Akan tetapi perbedaan sifat permukaan kedua bahan tersebut menimbulkan masalah apabila di padukan. Untuk mengatasi masalah kompatibilitas tersebut dibutuhkan perlakuan alkalinisasi pada kedua bahan tersebut.
Alkalinisasi dilakukan dengan larutan NaOH 0,25 M dan 0.5 M selama 6 jam ,8 jam, dan 10 jam di harapkan dapat meingkatkan kompatibilitas antar 2 bahan tersebut. Kompatibiltas dapat di tunjukan melalui sifat mekanis material komposit tersebut. Mencari fraksi volum serat yang optimal menjadi suatu hal yang harus di lakukan karena dapat berpotensi menimbulkan void. Maka fraksi volume 5%, 7,5%, dan 10% menjadi variabel dalam penentuan fraksi volume yang optimal.

Nowadays the urgency of the waste problem is increasing. One of the most difficult waste to be processed is plastic waste, the idea of plastic that can be degraded quickly become one of alternative solutions to these problems. materials such as organic fibers and polylactic acid bio-polymer begin to develop. However, differences in the surface properties of the two materials is become a problem to be solved. To overcome the compatibility issues, Fibers need alkalinization treatment on both of the materials.
Alkalinization performed with NaOH solution 0.25 M and 0.5 M for 6 hours, 8 hours, and 10 hours are expected to boost the compatibility of surface properties between two materials. Good compatibility can be indicated through the mechanical properties of the composite material. Searching for the optimal fiber volume fraction becomes a thing that should be done because it can potentially resulting voids in the microstructure. Then the volume fraction of 5%, 7.5%, and 10% are the variables to determine the optimal volume fraction of the composite.
"
Depok: Fakultas Teknik Universitas Indonesia, 2015
S60412
UI - Skripsi Membership  Universitas Indonesia Library
cover
Dimas Arya Thayeb
"ABSTRAK
Penggunaan serat alam Tandan Kosong Kelapa Sawit (TKKS) sebagai penguat dalam komposit polimer terus digalakkan sebagai alternatif bahan baku yang murah dan berlimpah. Namun, sifat hidrofilik yang dimiliki oleh serat alam TKKS akibat kandungan lignin dan hemiselulosa menyebabkan TKKS memiliki kompabilitas yang rendah dengan matriks polimer yang digunakan. Proses bleaching merupakan metode modifikasi permukaan yang bertujuan untuk meningkatkan sifat hidrofobisitas dari serat TKKS. Potensi penggunaan Hidrogen Peroksida (H2O2­) sebagai bleaching agent dalam larutan alkali menunjukan kemampuan untuk menghilangkan kandungan lignin, hemiselulosa, dan impuritas yang berada pada permukaan serat alam TKKS. Perubahan sifat permukaan TKKS kemudian diteliti menggunakan pengujian sudut kontak dengan metode sessile drop test, SEM, dan FTIR. Tegangan permukaan dari TKKS tanpa perlakuan menunjukan angka 35.18 dynes/cm dan meningkat menjadi 32.33 dynes/cm setelah dilakukan bleaching mengindikasikan adanya peningkatan sifat hidrofobik dari serat TKKS. Selain itu, analisis kuantitatif nilai dispersi menggunakan metode perhitungan statistik skewness ratio dan coefficient of variation menunjukan adanya kecenderungan peningkatan distribusi ukuran serat dari TKKS hasil bleaching. Nilai koefisien variasi yang menurun dari 1.40 menjadi 1.20 setelah perlakuan bleaching menunjukan kondisi distribusi serat TKKS yang lebih seragam. Selain itu, nilai skewness ratio serat TKKS hasil bleaching menunjukan peningkatan nilai dari 1.98 menjadi 2.13 mengindikasikan bahwa serat yang mengalami aglomerasi semakin sedikit. Sedangkan, pada perhitungan Nearest Neighbor Index (NNI), adanya penurunan nilai NNI dari 0.42 pada serat TKKS tanpa perlakuan menjadi 0.32 pada serat hasil perlakuan mengindikasikan meningkatnya kecenderungan serat TKKS untuk mengalami clustering.

ABSTRACT
The use of Oil Palm Empty Fruit Bunch (OPEFB) fibers as reinforcement in polymer composites continues to be promoted as an alternative to man-made fiber because of its inexpensive and abundant quantity. However, the hydrophilic nature of natural OPEFB fibers due to lignin and hemicellulose content causes OPEFB to have low compatibility with the common polymer matrix like polypropylene. Bleaching as a surface modification method is used to improve the of OPEFB fibers. The potential use of Hydrogen Peroxide (H2O2) as a bleaching agent in an alkaline solution shows the ability to eliminate lignin, hemicellulose, and impurities that are present on the surface of the natural OPEFB fibers. Changes in the surface properties of OPEFB are then examined using contact angle testing using sessile drop method, SEM, and FTIR analysis. The surface tension of the OPEFB without treatment shows the number as high as 35.18 dynes/cm and decreases to 32.33 dynes/cm after bleaching treatment, indicates an increase in the nature of the OPEFB fibers. In addition, quantitative analysis of dispersion values ​​using the statistical calculation method of skewness ratio and coefficient of variation showed tendency of increasing uniformity of size distribution on OPEFB fiber after bleaching treatment. The coefficient of variation decreased from 1.40 to 1.20 after the bleaching treatment showed a more uniform condition of the OPEFB fiber size distribution relative to its average size. In addition, the skewness ratio of post-bleaching OPEFB fibers shows an increase in value from 1.98 to 2.13 indicating that the agglomeration of fiber is getting sparse. Whereas, in the calculation of Nearest Neighbor Index (NNI), a decrease in the value of NNI from 0.42 on untreated OPEFB fibers to 0.32 on treated fibers indicates an increase in the tendency of OPEFB fibers to experience clustering.
"
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Juniko Nur Pratama
"Saat ini, plastik menjadi perhatian terkait dengan degradasi dan isu-isu lingkungan. Hal ini menyebabkan penelitian untuk mengembangkan bahan ramah lingkungan. Untuk meminimalkan dampak dari masalah tersebut, baru-baru ini penggunaan serat alam sebagai pengisi diperkenalkan karena biodegradabilitas dan ketersediaan. Serat alami yang menjanjikan adalah serat ijuk dari Arenga pinnata tanaman sebagai pengisi dan polypropylene polimer (PP) sebagai matriks. Sayangnya, serat alam dan polimer memiliki sifat yang berbeda, polimer memiliki sifat polar sedangkan serat alam bersifat non-polar sehingga mengurangi kompatibilitas dan dihasilkan kristalinitas yang sangat rendah. Untuk meningkatkan kompatibilitas dan kristalinitas, serat ijuk diberikan perlakuan dengan beberapa tahapan termasuk alkalinization dengan 5% dan 10% natrium hidroksida (NaOH), oksidasi dengan 3% dan 6% sodium hypochlorite (NaClO) dan hidrolisis dengan asam sulfat 20% (H2SO4) di urutan.
Tujuan dari perlakuan bertahap adalah untuk menghapus komponen seperti lignin, lilin, hemiselulosa, memfragmentasi lignin yang tersisa secara oksidatif dan menghilangkan bagian amorf masing-masing. Fourier-Transform Infrared (FT-IR) mengidentifikasi tingkat kompatibilitas sementara itu Differential Scanning Calorimetry (DSC) menunjukan kristalinitas dan Scanning Electron Microscope (SEM) menampilkan permukaan morfologi polypropylene.
Percobaan mengungkapkan bahwa efek dari serat ijuk dengan perlakuan bertahap dari 5% NaOH dan 10% NaOH menghasilkan kristalinitas polypropylene sekitar 31,2% dan 27,64% masing-masing dibandingkan dengan kristalinitas sebelum menambahkan "ijuk" serat untuk 16,8%. Hal ini menunjukkan bahwa seluruh perlakuan meningkatkan kompatibilitas dan kristalinitas polypropylene. Selain itu, penggunaan 5% NaOH menawarkan kristalinitas lebih baik dari polypropylene non-diobati. Percobaan menyimpulkan bahwa dengan menambahkan alkalinized serat ijuk perlakuan bertahap dapat meningkatkan kompatibilitas dan kristalinitas dari polypropylene.

Nowadays, plastics becomes concern associated with its degradation and environmental issues. It has led studies to develop an environmental-friendly material. To minimize the impact of those problems, recently the usage of natural fibers as a filler are introduced because of biodegradability and availability. The promising natural fiber is ijuk fiber from Arenga pinnata plant as a filler and polypropylene (PP) polymer as a matrix. Unfortunately, the natural fibers and polymers have the different properties on which polymers are polar while natural fibers are non-polar so that reducing the compatibility and resulting the poor crystallinity. To enhance the compatibility and crystallinity, ijuk fibers were prepared by multistage treatments including alkalinization with 5% and 10% sodium hydroxide (NaOH), oxidation with 3% and 6% sodium hypochlorite (NaClO) and hydrolysis with 20% sulphuric acid (H2SO4) in sequences.
The purposes of multistage treatments are to remove the components such as lignin, wax, hemicellulose, to cause an oxidative fragmentation of remaining lignin and to annihilate the amorphous parts respectively. Fourier-Transform Infrared (FTIR) confirms the compatibility meanwhile Differential Scanning Calorimetry (DSC) reveals the crystallinity and Scanning Electron Microscope (SEM) displays surface morphology of polypropylene.
The experiments were revealing that the effects of ijuk fibers by the multistage treatments of 5% NaOH and 10% NaOH resulting the crystallinity of polypropylene around 31,2% and 27,64% respectively compared to the crystallinity before adding the ijuk fibers for 16,8%. It indicates that the entire treatments increasing the compatibility and crystallinity of polypropylene. In addition, the use of 5% NaOH offers the better crystallinity than non-treated polypropylene. The experiments conclude that by adding alkalinized ijuk fibers of multistage treatments can increase the compatibility and crystallinity of polypropylene.
"
Depok: Fakultas Teknik Universitas Indonesia, 2015
T47073
UI - Tesis Membership  Universitas Indonesia Library
cover
Anandiza Yoga Pratama
"Pada penelitian ini dibuat komposit menggunakan polipropilena sebagai matriks dan serat sorghum sebagai penguat. Namun, polipropilena dan serat sorghum memiliki permasalahan yaitu sifat permukaan antara keduanya berbeda. Untuk memperbaiki sifat permukaan serat sorghum, perlu dilakukan modifikasi permukaan dengan perlakuan kimiawi seperti alkalinisasi, pemutihan dan hidrolisis asam. Proses alkalinisasi dilakukan menggunakan larutan NaOH 10% selama 2 jam. Proses pemutihan dilakukan dengan larutan NaClO2 1,7% selama 4 jam dan proses hidrolisis asam dilakukan dengan larutan H2SO4 25% selama 1 jam. Kemudian dilakukan proses hot melt mixing untuk dilakukan pencampuran antara PP dan serat sorghum. Pengaruh komposisi serat dan modifikasi serat sorghum menjadi fokus pada penelitian ini.
Hasil penelitian menunjukan bahwa kristalinitas, kompatibilitas dan kuat tarik komposit berpenguat serat perlakuan pemutihan lebih baik dibandingkan komposit berpenguat serat tanpa perlakuan. Sedangkan penambahan komposisi 5% & 10% serat perlakuan hidrolisis asam mengalami penurunan kekuatan tarik dibandingkan kuat tarik PP.

In this research composites was made using polypropylene as matrix and sorghum fibers as reinforcement. However, polypropylene and sorghum fiber has a problem that have different surface properties. To improve the surface properties of the sorghum fiber, surface modification needs to be done by chemical treatment such as alkalinization, bleaching and acid hydrolysis. alkalinization process is done by 10% NaOH solution for 2 hours. The bleaching process is done by 1,7% NaClO2 solution for 4 hours and the process of acid hydrolysis carried out by 25% H2SO4 solution for 1 hour. Then do the hot melt mixing process to do the mixing between the PP and fiber sorghum. The influence of fiber composition and modification of sorghum fiber on manufacture of PP/sorghum composites to be focused on this research.
The results showed that the crystallinity, compatibility and tensile strength of composite reinforced by bleaching treatment fiber is better than the composite reinforced by untreated fiber. While, the addition of the composition by 5% and 10% fiber to acid hydrolysis treatment decreased the tensile strength than tensile strength of PP.
"
Depok: Fakultas Teknik Universitas Indonesia, 2016
S65029
UI - Skripsi Membership  Universitas Indonesia Library
cover
[Fakultas Kedokteran Gigi. Universitas Indonesia, Journal of Dentistry Indonesia], 2006
pdf
Artikel Jurnal  Universitas Indonesia Library
cover
Karo Karo, Aloma
"Pencangkokan 4-vinilpiridin pada serat polipropilen dengan teknik radiasi, sebagai alternatif untuk membuat serat penukar ion telah dilakukan, Pengaruh kondisi radiasi, metoda pencangkokan, dosis, laju dosis, jenis pelarut, komposisi pelarut , dan konsentrasi monomer terhadap kadar pencangkokan dipelajari. Analisis dan karakterisasi serat polipropilen sebelum dan sesudah pencangkokan dilakukan dengan, ESR, FT-IR, DTAITGA, XRD, dan SEM-EDAX . Kapasitas penukaran serat PP-g-4VP terhadap ion Cue` dalam larutan analisis dengan ICP-MS.
Hasil yang diperoleh dari ESR menunjukkan bahwa kondisi radiasi yang terbaik adalah oakum. Metoda yang memberikan kadar pencangkokan tertinggi adalah metoda simultan. Semakin tinggi dosis, laju dosis dan konsentrasi monomer, maka makin tinggi kadar pencangkokan. Makin menurun polaritas pelarut dalam pelarut homolog alkohol maka makin tinggi kadar pencangkokan, akan tetapi semakin tinggi kadar air didalam pelarut alkohol semakin tinggi kadar pencangkokan. Pelarut n-butanol menunjukkan kinetika pencangkokan lebih baik, dengan laju pencangkokan awal lebih tinggi di banding pelarut campuran metanol-air , Hubungan antara laju pencangkokan awal terhadap laju dosis dalam pelarut n-butanol adalah Rp = C I 0.35 ; sedangkan dalam pelarut metanol- air Rp = C I "7.
Spektrum serapan FT-IR menunjukkan munculnya pita serapan vibrasi ulur u (C=C) dan u(C-H) aromatik pada bilangan gelombang 1625 dan 3020 cm-', dan pita serapan vibrasi ulur u (C-N) pada bilangan gelombang 1177 dan 1388 cm 1, yang berarti 4-vinilpiridin berhasil dicangkokan pada serat polipropilen. Pengamatan dengan SEM memperlihatkan perbedaan diameter dan permukaan serat polip ropilen sebelum dan sesudah dicangkok, sedangkan dari EDAX menunjukkan ion Cue+ telah diadsorpsi oleh serat PP-g-4VP dan terdistribusi secara merata, dengan kapasitas penukaran 3,4 mek/gram serat. Termogram DTAITGA menunjukkan pencangkokan 4-vinilpiridin pada serat polipropilen menunukkan kesetabilan termalnya, dan dari diffraktogram XRD menunjukkan terjadi perubahan fasa kristalin serat polipropilen setelah dicangkok.

Influence of Solvents on Graft Copolymerization Kinetics of 4-vinilpiridin onto Polypropylene Fibers by Simultaneous Methods in Vacuum Atmosphere Radiation graft copolymerization of 4-vinilipiridin onto polypropylene fibers, for synthesis of ion exchange fibers has been done. The effect of radiation condition, graft methods, dose, dose rate, solvents and monomer concentrations on the grafting yields was also studied. Analysis and characterization of polypropylene fibers before and after grafting was done by ESR, FT-IR, DTAITGA, XRD and SEM-EDAX. The ion exchange capacity of PP-g-4VP fibers on Cue+ ion was determined by ICP-MS.
The ESR spectra showed that vacuum atmosphere was the best irradiation condition. The higher grafting yields were obtained by simultaneous method. The grafting yields increased with increasing dose, dose rate, monomer concentration and H2O content within alcohol-water solvents system. The grafting yields also increased if polarity of alcohol decreased in using homologue alcohol solvent system. The initial copolymerization rate in n-butanol solvents was higher than methanol-water solvents, with Rp = C 10.35 in n-butanol and, Rp = C I 0.57 in methanol-water solvents, Infra red spectra showed characteristic band sorption on wave length 1625 and 3020 cm 'I for C-H and C=C aromatic stretching, and 1177 and 1388 cm-' for C-N stretching. Observation by using SEM-EDAX showed the difference between polypropylene before and after grafted by 4-vinilpiridin, and Cue+ ion was homogeneously adsorbed by PP-g-4VP fibers, with adsorbed capacity 3.4 meg/gr. DTAITGA thermogram showed, that grafted 4-vinilpiridin onto polypropylene fibers was decreased its thermal stability, and X-ray diffractogram showed that crystalinity of polypropylene was changed after grafted by 4-vinilpiridin.
"
Depok: Universitas Indonesia, 1997
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Thadila Arinka Viranti
"ABSTRACT
Latar Belakang: Bleaching kimiawi dapat merusak email gigi dan jaringan lunak. Daun stroberi mempunyai zat aktif berupa asam ellagat yang dapat berperan sebagai oksidator pada proses pemutihan gigi. Tujuan: Mengetahui perubahan warna pada email gigi setelah aplikasi ekstrak murni daun stroberi serta mengetahui sistem ruang warna yang paling sesuai untuk mengukur perubahan warna tersebut. Metode: Menggunakan ekstrak murni daun stroberi dengan konsentrasi 25 dan 50 diaplikasikan pada email gigi selama 7 jam hingga 28 kali aplikasi. Analisis warna menggunakan spektrofotometri dengan software Adobe Photoshop. Hasil: Perubahan warna email gigi mejadi lebih terang. Kesimpulan: Ekstrak murni daun stroberi mampu mengubah warna email gigi menjadi lebih terang. RGB merupakan sistem ruang warna yang paling sesuai untuk mengukur perubahan warna email gigi setelah bleaching.

ABSTRACT
Background Bleaching using chemicals can damage tooth enamel and soft tissue. Strawberry leaves contain active compounds in the form of acid ellagat that can act as an oxidant in the process of teeth whitening. Objective To determine discoloration of the tooth enamel after application of direct extracts of strawberry leaves and determine the color space which appropiate to measure the color change. Methods Using direct extracts of strawberry leaves with a concentration of 25 and 50 applied on enamel for 7 hours until 28 times repetition of application. Color analysis conducted using a spectrophotometry with software Adobe Photoshop. Results Enamel surface becoming brighter. Conclusions Direct extraction of strawberry leaves able to change the color of the enamel becomes brighter. RGB is a color space system which most appropriate for measuring changes in the color of enamel after bleaching. "
2016
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Rachmat Ferdian
"Kelangkaan minyak bumi yang tidak terbarukan terus mendorong kenaikan produk-produk turunannya, salah satunya adalah plastik. Untuk mencari alternatif dari hal tersebut, dikembangkanlah plastik komposit yang terbuat dari Polylactic Acid (PLA) dengan penambahan serat ijuk diharapkan mempunyai sifat mekanis yang cukup tinggi dan ramah lingkungan. Kompatibilitas dari kedua bahan tersebut menjadi perhatian utama untuk menciptakan material komposit dengan sifat mekanis yang baik. Penelitian ini menggunakan matriks PLA dengan serat ijuk yang dicampur dengan metode pelarutan menggunakan Dichloromethane dan kemudian dicetak menjadi sampel uji tarik dengan metode cetak panas. Variabel yang digunakan adalah fraksi volum penguat 0%; 10%; 20%; 30%; 40% dan 50%, serta modifikasi permukaan serat dengan perlakuan alkali (NaOH) 0,25 M selama 30 menit untuk meningkatkan kompatibilitas serat terhadap matriks. Hasil pengujian menunjukkan penurunan sifat kekuatan tarik dan Modulus Young terhadap fraksi volum penguat dari 0% hingga 50%, yang tidak menunjukkan efek penguatan serat terhadap matriks untuk sampel tanpa modifikasi perrmukaan, sementara nilai elongasi menunjukkan tren peningkatan. Hal ini diakibatkan kompatibilitas yang buruk antara matriks dan serat. Setelah dilakukan modifikasi permukaan serat, terjadi peningkatan dari sifat mekanis komposit tersebut. Hasil pengujian FTIR menunjukkan terjadinya pengurangan lignin dan hemiselulosa yang dapat meningkatkan kompatibilitas matriks dan serat.

Petroleum as a non-renewable resources shows price increment for its derivative products, which one of those is plastics. The development for an alternative solution are developed, that is composite material from Polylactic Acid (PLA) which combined with Ijuk (Arenga pinnata) with the main focus in their compatibility to meet the demand for high specific strength and environmetalfriendly material. This research use PLA as a matrices dan Ijuk as a reinforcement, which is solution mixed using Dicholoromethane and then pressed by hot pressing method to formed tensile test specimens. The variations are volume fraction and fiber surface modification. Volume fraction used are 0%; 10%; 20%; 30%; 40% and 50%, while alkali treatment with NaOH 0,25M for 30 minutes is used for surface modification. Tensile test results show the decreament in tensile strength and Young’s Modulus versus fiber addition from 0-50%, while the elongation shows the conversely results, is showing no strengthening effect of fiber to the matrices for untreated composites. This is due to poor compatibility between matrices and fibers. After surface modification, tensile test results show the improvement in the mechanical properties due to elimination of lignin and hemicellulose which increases its compatibility, supported by the FTIR test results.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
T34974
UI - Tesis Membership  Universitas Indonesia Library
cover
Chaira Musytaka Sukma
"Latar Belakang: Aplikasi bahan internal bleaching dapat meninggalkan residu radikal bebas yang akan menghambat penetrasi resin tag. Penghilangan residu radikal bebas dapat dilakukan dengan pengaplikasian bahan antioksidan berupa natrium askorbat. Pemberian natrium askorbat dapat mencegah timbulnya terminasi dini, sehingga dapat memungkinkan proses polimerisasi resin adhesif dapat berlanjut. Penggunaan konsentrasi natrium askorbat yang sebanding dengan konsentrasi hidrogen peroksida diharapkan dapat menghilangkan residu radikal bebas sehingga nantinya dapat meningkatkan resistensi resin komposit yang dilihat melalui kedalaman panjang penetrasi resin tag.
Tujuan: mengetahui kedalaman panjang penetrasi resin tag pada dentin gigi pasca internal bleaching dengan hidrogen peroksida yang diaplikasikan natrium askorbat 10% dan 35% selama 2 menit dan 10 menit.
Metode: proses internal bleaching dilakukan dengan menggunakan hidrogen peroksida 35% selama 5 hari. Selanjutnya, dibagi menjadi 5 kelompok uji yaitu tanpa pemberian natrium askorbat, diberikan askorbat 10% selama 2 menit, diberikan natrium askorbat 10% selama 10 menit, diberikan natrium askorbat 35% selama 2 menit, dan diberikan natrium askorbat 35% selama 10 menit. Pengamatan kedalam penetrasi resin tag dilakukan dengan menggunakan Confocal Laser Scanning Microscopy (CLSM).
Hasil: terdapat perbedaan kedalaman penetrasi resin tag pada gigi pasca internal bleaching yang diberikan bahan antioksidan berupa natrium askorbat dan tanpa antioksidan, diuji dengan menggunakan CLSM.
Kesimpulan: pemberian bahan antioksidan berupa natrium askorbat dapat memengaruhi kedalaman penetrasi resin tag pada gigi pasca internal bleaching.

Background: The application of internal bleaching materials can leave free radical residues that will inhibit the penetration of resin tags. Application of sodium ascorbate as antioxidant agent will remove the residual free radical. Sodium ascorbate can prevent premature termination, thus allowing the adhesive resin polymerization process to continue. Concentration of sodium ascorbate should be proportional to the hydrogen peroxide concentration so that will remove free radical residues and it can increase the composite resin resistance as seen through the depth of penetration length of the resin tag.
Objective: determine the depth of penetration length of resin tags on dentin after internal bleaching with hydrogen peroxide which was applied with 10% and 35% sodium ascorbate for 2 minutes and 10 minutes.
Methods: the internal bleaching process was carried out using 35% hydrogen peroxide for 5 days. Furthermore, the specimen divided into 5 test groups, without sodium ascorbate, 10% sodium ascorbate for 2 minutes, 10% sodium ascorbate for 10 minutes, 35% sodium ascorbate for 2 minutes, and 35% sodium ascorbate for 10 minutes. Observations into the resin tag penetration were carried out using Confocal Laser Scanning Microscopy (CLSM).
Results: there were differences in the depth of penetration of resin tags on teeth after internal bleaching which was given an sodium ascorbate and without sodium ascorbate, tested using CLSM.
Conclusion: application of sodium ascorbate can affect the depth of penetration of resin tags on teeth after internal bleaching.
"
Jakarta: Fakultas Kedokteran Gigi Universitas Indonesia, 2021
SP-pdf
UI - Tugas Akhir  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>