Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 124241 dokumen yang sesuai dengan query
cover
Billy Aprianto
"Modifikasi permukaan Ti6Al4V dengan fabrikasi TiO2 nanotubes menggunakan metode anodisasi dan uji pembentukan biofilm telah dilakukan. Hasil anodisasi yang diperoleh dikalsinasi pada suhu 5000C dengan aliran udara tekan. Hasil beberapa karakterisasi yang dilakukan diperoleh nilai energi celah pada Ti6Al4V yang telah dimodifikasi sekitar 3,3 eV dengan ukuran kristal 6,72 nm dan komponen V tidak terdeteksi. Uji pembentukan biofilm secara in vitro memperoleh hasil bahan Ti6Al4V yang dianodisasi memiliki ketahanan terhadap pembentukan biofilm oleh Streptococcus mutans dan memperoleh hasil hingga jam ke-8 pengukuran mencapai 33% konsentrasi bakteri yang menempel pada plat dibandingkan model kontrol. Ti6Al4V yang dianodisasi selama 4 jam menunjukkan kinerja ketahanan terhadap biofilm yang mencapai 31% pada jam ke-8. Semakin lama waktu anodisasi, kinerja fotokatalitik pun semakin meningkat diduga karena semakin panjang nanotubes yang terbentuk. Kinerja fotokatalitik pada bahan Ti6Al4V berpeluang untuk ditingkatkan mengingat struktur kristal yang terbentuk belum maksimal.

Surface modification of Ti6Al4V with TiO2 nanotubes fabrication by anodization method and biofilm test had been done. The products after anodization process are furnaced in 5000C within air stream. The results of some characterization of Ti6Al4V are 3,3 eV for band gap energy, 6,72 nm for the size of crystals, and for V component couldn’t be detected. Biofilm’s tests exhibit that modified Ti6Al4V has the ability to inhibit the formation of biofilm by Streptococcus mutans until 8 hours of experiment periods for 33% of bacterial concentration on the material, when comparing to the control. Ti6Al4V anodized for 4 hours exhibits the increasing of ability to inhibit the formation of biofilm for 31% of bacterial concentration. The longer time of anodization process makes photocatalytic activity becomes optimum, which is predicted because of the longer nanotubes. The modified Ti6Al4V has great potential in photocatalytic activity with improving the crystal’s structure."
Depok: Fakultas Teknik Universitas Indonesia, 2013
S46100
UI - Skripsi Membership  Universitas Indonesia Library
cover
Billy Aprianto
"Optimalisasi morfologi dan kristalinitas TiO2 nanotubes (TNT) yang difabrikasi pada permukaan Ti6Al4V dengan metode anodisasi dan dikristalisasi menggunakan variasi metode, yaitu pemanasan menggunakan furnace yang dialiri udara dengan variasi suhu operasi 500° - 800°C dan metode hydrothermal treatment dengan variasi suhu 150°-200°C selama 3 jam telah dilakukan.
Hasil karakterisasi pada sampel menunjukkan adanya peralihan fase kristal dari anatase menjadi rutile pada rentang suhu 600°C - 650°C dengan ukuran kristal rata-rata pada setiap variasi adalah 18 nm.
Hasil uji pembentukan biofilm secara in vitro dengan bakteri Streptococcus mutans menunjukkan sampel Ti6Al4V/TNT yang dikristalisasi pada suhu 600°C memiliki kinerja fotokatalitik yang paling baik, dengan hasil sebesar 21% konsentrasi bakteri yang menempel pada plat Ti6Al4V/TNT dibandingkan dengan model kontrol pada jam ke-24 pengukuran.
Hasil ini menunjukkan sampel Ti6Al4V/TNT dengan suhu kristalisasi 600°C merupakan kondisi optimum untuk menghambat pembentukan biofilm dalam penelitian ini. Kinerja fotokatalitik pada bahan Ti6Al4V/TNT berpotensi untuk ditingkatkan menggunakan kombinasi teknologi lainnya.

Morphology and crystalinity optimalization of TiO2 nanotubes (TNT) on Ti6Al4V using anodization method and various crystalization method (heat treatment by furnace within air stream at 500°-800°C and heat treatment using hydrothermal treatment method at 150°-200°C) had been done.
Characterizations of the samples show that there are a crystal phase changing from anatase to rutile at 600°-650°C in heat treatment using furnace, with 18 nm for crystal size in average.
Biofilm's test exhibit that Ti6Al4V/TNT sample that crystalized at 600°C has the best performance in inhibiting biofilm formation, which can achieve 19% of biofilm concentration on the material, compared to the control.
The result show that Ti6Al4V/TNT that crystalized at 600°C has the optimum morpholgy and crystalinity to inhibit the biofilm formation. The modified Ti6Al4V has great potential in biomedical application, due to its photocatalytic performance and TiO2 characteristics that can be combined with others technology to make better implants.
"
Depok: Fakultas Teknik Universitas Indonesia, 2014
T41808
UI - Tesis Membership  Universitas Indonesia Library
cover
Andry Prasthio
"Penelitian ini menghasilkan katalis komposit Zeolit Alam Lampung (ZAL) terintegrasi dengan TiO2 yang dapat mengeliminasi polutan gas NO2 secara simultan sehingga dapat diaplikasikan sebagai masker kesehatan. Katalis komposit dibuat dengan mechanical mixturing dan didapatkan komposisi TiO2 10%-ZAL 90% sebagai yang terbaik dalam mengeliminasi polutan gas NO2. Katalis komposit ini akan mendegradasi gas NO2 menjadi HNO3 yang bersifat non-toksik lewat proses adsorpsi dan fotokatalisis. Katalis komposit ini dapat mendegradasi gas NO2 dalam paparan konsentrasi awal 0,15-0,3 ppm dalam waktu 1,1-1,82 jam."
Depok: Fakultas Teknik Universitas Indonesia, 2012
S42939
UI - Skripsi Open  Universitas Indonesia Library
cover
Mahmud Sudibandriyo
Depok: Fakultas Teknik Universitas Indonesia, 2007
LP-pdf
UI - Laporan Penelitian  Universitas Indonesia Library
cover
Silitonga, Johannes Ivan Dennis
"Penelitian ini membandingkan karakteristik pengabutan dan pembakaran dari campuran minyak nabati dan bahan bakar minyak pada setiap rasio pencampuran nya. Semburan nyala api pada pembakaran yang beroperasi pada tekanan 0,2 hingga 1,2 bar diamati secara optis. Bahan bakar nabati (BBN) memiliki kekentalan (viskositas) yang besar sehingga menjadi kendala dalam proses pembakaran. Karena itu untuk menurunkan viskositas nya perlu dicampur dengan bahan bakar minyak (BBM). Pembakaran yang baik memerlukan proses pengabutan yang baik. Pada penelitian ini proses pengabutan nya menggunakan nosel jet. Pengukuran kualitas pengabutan dan pembakaran dilakukan dengan metode fotografi dan perangkat lunak pemrosesan citra. Hasilnya menunjukkan bahwa rasio campuran BBN dan BBM yang terbaik adalah 40% : 60% untuk semua jenis campuran (minyak jelantah dan solar, minyak curah dan solar, minyak nyamplung dan solar serta minyak curah dan minyak tanah) dan tekanan operasi terbaik adalah 1,2 bar. Pada kondisi tersebut, campuran minyak curah dan minyak solar memiliki rerata suhu nyala yang paling tinggi (391,6oF) dan distribusi partikel aerosol terkecil yang paling tinggi (73%) meskipun masih di bawah BBM murni (100%).

The spray atomization and combustion characteristic of vegetable oil and fosil fuel are compared to those ratio of mixtures on this paper. The spray flame was contained in an optically accessible combustor which operated at 0,2 - 1,2 bar of air pressure. Vegetable Fuel (VF) contains high viscosity that has been a, constraint in the combustion process; it needs to be mixed with Fosil Fuel (FF) in order to decrease the VF viscosity. A fine atomization process is necessary to fix the combustion. Research of atomization process was tested by using nozzle jet. The atomization and combustion quality were investigate by photographic method and image processing software was used to measure the spray droplet size. As a testing result, ratio mixture of 40% : 60% of VF and FF was good ratio mixtures ( used cooking oil diesel oil, cooking oil and diesel oil, nyamplung oil and diesel fuel, cooking oil and kerosene) compared to others ratio which operated at 1,2 bar of air pressure implying flame temperature. The flame temperatur of cooking oil and diesel oil mixture reached (391,6oF) as the highest mean temperature and distribution of aerosol particle reached (73%) although produced lower than fosil fuel (100%)."
Depok: Fakultas Teknik Universitas Indonesia, 2014
S57711
UI - Skripsi Membership  Universitas Indonesia Library
cover
Abubakar Adeni
"Reaktor plasma dengan konfigurasi umpan 3-lewatan untuk konversi gas CO2 dan CH4 perlu dimodelkan agar dapat merepresentasikan fenomena fisika dan kimia yang terjadi dalam reaktor. Pemodelan ini juga bertujuan mendapatkan kinerja reaktor yang diinginkan agar bisa digunakan sebagai dasar scale-up. Model reaktor disimulasikan dalam tiga dimensi menggunakan COMSOL Multiphysics dengan melihat pengaruh variasi laju alir umpan, temperatur di dalam reaktor, serta rasio mol umpan terhadap konversi dan produk syngas yang dihasilkan. Konversi tertinggi dicapai pada laju alir 4,6 mL/ menit dengan konversi CO2 sebesar 22% dan konversi CH4 sebesar 88,4% dengan rasio syngas yang dihasilkan CO2: CH4 = 1:1,14. Konversi yang dihasilkan tidak mengalami perubahan yang signifikan dengan naik atau turunnya temperatur di dalam reaktor. Dari variasi rasio mol umpan, konsentrasi CO yang dihasilkan meningkat sebanding dengan naiknya konsentrasi umpan CO2. Konsentrasi H2 yang dihasilkan meningkat sebanding dengan naiknya konsentrasi umpan CH4.

Plasma reactor with 3-pass flow configuration for conversion CO2 and CH4 gas needs to be modeled in order to represent the physical and chemical phenomena that occur in the reactor. This modeling also aims to obtain the desired performance of the reactor to be used as the basis for scale-up. Reactor modeled in three dimensions using COMSOL Multiphysics to see the effect of the feed flow rate variations, the temperature inside the reactor, as well as the mole ratio of the feed to the conversion and syngas produced. The highest conversion achieved at a flow rate 4.6 mL/min, respectively the conversion of CO2 and CH4 is 22% and 88.4% with a ratio syngas produced CO2: CH4 = 1: 1.14. The conversion in the reactor did not change significantly with the increase or decrease the temperature in the reactor. The concentration of CO produced increase with increasing inflow concentration of CO2. The concentration of H2 produced increase with increasing inflow concentration of CH4."
Depok: Fakultas Teknik Universitas Indonesia, 2015
S59083
UI - Skripsi Membership  Universitas Indonesia Library
cover
Asyari Fauzan
"Kebanyakan dari penghantaran obat untuk mata bagian dalam atau posterior adalah melalui jalur topikal dan sangat jarang melalui jalur sistemik dan sebelum obat dapat mencapai kornea, terlebih dahulu obat tersebut harus melewati pelindung mata yang terdapat dibagian anterior. Salah satu solusi yang dapat dilakukan adalah dengan memformulasikan pelepasan terkendali obat dengan menggunakan modifikasi mikropratikel Poly(lactide acid) (PLA) dan Poly(Lactide-co-Glyoclide Acid) (PLGA) dengan menggunakan surfaktan kationik didodecylammonium bromide (DMAB).
Dari penelitian ini, didapatkan hasil uji enkapsulasi dan pemuatan obat untuk PLA Acid Terminated 15,49 ± 0,17 % dan 18,33 ± 0,24 %, PLA Ester Terminated 13,07 ± 0,15 % dan 15,04 ± 0,2 %, serta PLGA (50:50 Acid Terminated) 15,3 ± 0,25 % dan 18,03 ± 0,35 %. Serta kuran partikel yang dihasilkan dengan PVA 0,002% untuk PLA Acid Terminated 4,42 ± 1,57, PLA Ester Terminated 1,26 ± 0,77, serta PLGA (50:50 Acid Terminated) 9,89 ± 2,32.

Most of the drug to the inner eye or posterior is through topical and very rarely through systemic and before the drug can reach the cornea, the first drug must pass through eye protection contained in anterior. One solution that can be done is to formulate controlled release of drugs using a modified micropartciles Poly (lactide acid) (PLA) and Poly (Lactide-co-Glyoclide acid) (PLGA) using a cationic surfactant didodecylammonium bromide (DMAB).
From this research, test results obtained encapsulation and drug loading for PLA Acid Terminated 15.49 ± 0.17% and 18.33 ± 0.24%, PLA Ester Terminated 13.07 ± 0.15% and 15.04 ± 0 , 2%, and the PLGA (50:50 Acid Terminated) 15.3 ± 0.25% and 18.03 ± 0.35%. As well as the size of the particles produced by the PVA 0.002% for the PLA Acid Terminated 4.42 ± 1.57, 1.26 ± PLA Ester Terminated 0.77, and PLGA (50:50 Acid Terminated) 9.89 ± 2.32.
"
Depok: Fakultas Teknik Universitas Indonesia, 2015
S59066
UI - Skripsi Membership  Universitas Indonesia Library
cover
Dewi Tristantini Budi
Depok: Fakultas Teknik Universitas Indonesia, 2001
LP-pdf
UI - Laporan Penelitian  Universitas Indonesia Library
cover
Praswasti Pembangun Dyah Kencana Wulan
Depok: Universitas Indonesia, 2005
LP-Pdf
UI - Laporan Penelitian  Universitas Indonesia Library
cover
<<   1 2 3 4 5 6 7 8 9 10   >>