Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 11028 dokumen yang sesuai dengan query
cover
cover
Aditya Dharmawan
"Preparasi tekstil termodifikasi TiO2 dengan mengikuti prosedur sol gel dan pad-dry curetelah berhasil dilakukan.Kinerja katalis diuji dengan eliminasi metilen blue dan desinfeksi E.Coli. Sifat mekanik dipelajari dengan uji tarik, uji elongasi dan uji kerontokan. Sementara studi katalis pada substrat dipelajari dari karakterisasi SEM, EDS, FTIR DRS dan XRD.Post-treatment hidrotermal menghasilkan katalis yang tersebar merata pada tekstil namun lebih rentan terlepas, sementara post-treatment furnace katalisnya terpusat di beberapa titik namun katalis yang lebih sulit terlepas. Kekuatan mekanik tensil dan elongasi terbaik dicapai oleh TiO2-5-F-Si dengan kekuatan tensil 67,10 ± 0,21 MPa dan elongasi 111,0 ± 29,7 %.
Uji eliminasi metilen blue menunjukkan TiO2-12-H-Si setelah 5 jam adalah 79,8% dibandingkan dengan TiO2-25-H-Si yang dapat mengeliminasi 1,05 kali lipat namun dengan bahan baku 2 kalinya. Pada desinfeksi E.Coli,TiO2-12-H-Si mendesinfeksi E.Coli sebesar 67,4% setelah 30 menit dibandingkan dengan TiO2-25-H-Si yang mendesinfeksi 1,14 kali lipat namun dengan bahan baku 2 kalinya.

Preparation using sol gel and pad dry cure method had been done. Mechanical study observed are tensile test, elongation test and disattachement test. While catalyst on substrate observed using SEM, EDS, FTIR, DRS and XRD characterization. Hydrothermal post treatment results a diverge catalyst distribution but with tendency to be disattached from substrate, while furnace post treatment results a converge catalyst distribution but with low tendency to be disattached from substrate. Best tensile and elongation result achieved by TiO2-5-F-Si with tensile strength 67,10 ± 0,21 MPa and elongation 111,0 ± 29,7 %.
From methylene blue elimination, TiO2-12-H-Si showed 79,8% elimination, compared to TiO2-25-H-Si which is 1,05 times better than TiO2-12-H-Si but using twice the material used. On E.Coli desinfection, TiO2-12-H-Si able to desinfect 67,4% E.Coli after 30 minutes, compared to TiO2-25-H-Si which is 1,14 times better than TiO2-12-H-Si but using twice the material used.
"
Depok: Fakultas Teknik Universitas Indonesia, 2013
T35287
UI - Tesis Membership  Universitas Indonesia Library
cover
Aritonang, Anthoni Batahan
"ABSTRAK
Disertasi ini membahas tentang metode yang praktis dan biaya murah untuk membuat fotokatalis Ag/N ko-doped TiO2 bersifat responsif terhadap cahaya sinar tampak dan diterapkan sebagai elektroda sistem fotoelektrokatalitik. Penelitian ini diawali sintesis film N-doped TiO2 pada permukaan kaca konduktif SnO2F dengan metode sol-gel menggunakan titanium tetraisopropoksida Ti OC4H9 4 sebagai prekursor TiO2. Berdasarkan hasil karakterisasi diketahui doping N pada struktur kisi TiO2 telah berhasil, namun demikian aktivitas fotokatalisisnya masih rendah. Tahapan penelitian berikutnya, film N-doped TiO2 disintesis di atas permukaan logam Ti dengan metode anodisasi menggunakan foil Ti dalam elektrolit etilen glikol yang mengandung amonium florida NH4F; 0,3 , air 0,3 dan trietilamina 0,02 . Potensial diatur tetap 40 V selama 60 detik, hingga didapatkan amorfous Ti OH 6 dan trietilamina tersolvasi di permukaannya. Perlakuan kalsinasi terhadap amorfous Ti OH 6 pada suhu 450oC kondisi atmosferik N2 selama 3 jam, menyebabkan beberapa atom O disubstitusi oleh atom N dalam struktur kisi TiO2 membentuk kristal N-doped TiO2 yang memiliki band gap 2,7 eV. Untuk meningkatkan aktivitas fotokatalisis di daerah sinar tampak, permukaan N-doped TiO2 didekorasi dengan partikel Ag secara deposisi elektrokimia, menggunakan larutan AgNO3-EDTA dengan potensial deposisi 1V dan variasi waktu 5-25 detik, hingga didapatkan fotokatalis Ag/N ko-doped TiO2. Hasil pengukuran XRD memperlihatkan Ag/N ko-doped TiO2 terdiri dari kristal anatase, dan diamati puncak difraksi pada daerah 2 Theta 44,8o yang merupakan karakteristik Ag 111 , membuktikan bahwa partikel Ago telah terdeposisi pada matrik N-doped TiO2. Foto FESEM memperlihatkan morfologi permukaan N-doped TiO2 berbentuk nanotube, yang memiliki tebal dinding tube rata-rata 15 nm, diameter mulut tube 70 nm dan tinggi 900 nm. Hasil pengukuran HRTEM memperlihatkan partikel Ago berukuran 15-40 nm dan mapping EDX membuktikan bahwa nanopartikel Ago terdistribusi merata di permukaan N-doped TiO2 dengan rasio atom 0,61 . Spektrum XPS N 1s pada daerah binding energi 400,6 eV membuktikan keberadaan atom N dalam matrik Ag/N ko-doped TiO2 sebagai indikasi pembentukan ikatan N-Ti-O yang didukung hasil pengukuran FTIR. Spektrum XPS Ag 3d memperlihatkan puncak serapan ganda yang terpisah pada binding energi 368,6 eV dan 374,6 eV, dengan energi pemisahan 6,0 eV, memperkuat bukti bahwa Ag terdeposisi sebagai partikel Ago. Partikel Ago terdeposisi meningkatkan kemampuan N-doped TiO2 menyerap sinar tampak l=550 nm sebagai kontribusi serapan surface plasmon resonance SPR . Tahapan penelitian selanjutnya, Ag/N ko-doped TiO2 digunakan sebagai elektroda kerja sistem fotoelektrokatalitik FEK dengan pemberian bias potensial. Berdasarkan uji kinerja elektroda pada degradasi larutan MB secara fotoelektrokatalisis FEK , terbukti bahwa elektroda Ag/N ko-doped TiO2 memiliki aktivitas fotokatalisis yang tinggi, mampu mendegradasi larutan MB pada konsentrasi 10 ppm selama 4 jam, memberikan rasio MB terdegradasi 92 , lebih tinggi dibandingkan dengan N-doped TiO2 dan TiO2 masing-masing mampu mendegradasi 56 dan 14 . Pemberian bias potensial 0,2 V pada permukaan elektroda Ag/N ko-doped TiO2, mampu meningkatkan aktivitas FEK degradasi MB, memberikan konstanta laju FEK k=9x10-3/menit , yang mana 4,5 kali lebih cepat dibandingkan dengan proses fotokatalisis FK tanpa pemberian bias potensial k=2x10-3/menit . Beberapa faktor yang mempengaruhi FEK degradasi MB telah dievaluasi, yakni pH optimum adalah 9,0 ; bias potensial optimum 0,2 V dan konsentrasi awal larutan MB optimum 10 ppm. Elektroda Ag/N ko-doped TiO2 yang dikembangkan memiliki kestabilan yang tinggi, setidaknya 5 kali pemakaian masih memperlihatkan aktivitas fotokatalitik yang baik sehingga sangat ekonomis untuk diterapkan dalam mendegradasi polutan organik.

ABSTRACT
The dissertation discusses practical and inexpensive methods for synthesis of Ag N co doped TiO2 photocatalysts responsive to visible light and used as photoelectrocatalytic electrodes system. Initial phase of this study was synthesized N doped TiO2 film on SnO2 F conductive glass surface with sol gel method using titanium tetraisopropoksida Ti OC4H9 4 as TiO2 precursor. Based on the characterization results known doping N on TiO2 lattice structure has been successful, however photocatalysis activity is still low. The next stage of the study, the N doped TiO2 film was synthesized on the surface of the Ti metal by anodizing method using a Ti foil in an ethylene glycol electrolyte containing ammonium fluoride NH4F 0.3 , water 0.3 and triethylamine 0.02 . The anodizing process is carried out at a potential of 40 V for 1 hour, forming an amorphous Ti OH 6 and triethylamine dissolved on its surface. Calcined treatment of amorphous Ti OH 6 at 450 C atmospheric conditions N2 for 3 hours, causing some O atoms substituted by N atom in lattice structure of TiO2 to form N doped TiO2 crystals having band gap of 2.7 eV. This method is very effective and efficient, where the N doping process takes place optimally and simultaneously with the formation of TiO2 crystal. To improve the photocatalysis activity in visible light region, the surface of N doped TiO2 was decorated with Ag particles by electrochemical deposition method, using AgNO3 EDTA solution with a potential deposition 1V and a time variation 5 25 second, to obtain Ag N co doped TiO2 photocatalyst. The XRD measurements showed that Ag N co doped TiO2 consisted of anatase crystals, and observed the diffraction peak at 2 Theta 44.8o region which is characteristic of Ag 111 , proving that the Ago particle has been deposited on an N doped TiO2 matrix. FESEM images show the surface morphology of N doped TiO2 in the form of nanotubes, which have an average thickness of 15 nm tube wall, 70 nm diameter mouth tube and 900 nm height. The HRTEM measurements show that Ago particles of 15 40 nm and EDX mapping demonstrate that Ago nanoparticles are evenly distributed on the surface of N doped TiO2 with an atomic ratio of 0.61 . The XPS N 1s spectrum in the energy binding region of 400.6 eV proves the presence of N atoms in the Ag N co doped TiO2 matrix as an indication of N Ti O bond formation supported by FTIR measurements. The XPS Ag 3d spectrum shows a separate double absorption peak on energy bindings of 368.6 eV and 374.6 eV, with a 6.0 eV separation energy, reinforcing evidence that Ag is deposited as an Ago particle. The Ago particle enhances the ability of N doped TiO2 to absorb the visible light l 550 nm as a contribution of surface plasmon resonance SPR absorption. The next step of this research, the Ag N co doped TiO2 is used as the electrode of photoelectrocatalytic PEC system and potential bias was applied. Based on the electrode activity test on the degradation of MB solution by photoelectrocatalysis PEC , it is proved that the Ag N co doped TiO2 electrode has high photocatalytic activity, capable of degrading the MB solution at 10 ppm concentration for 4 hours, giving a degradable MB ratio of 92 higher compared with N doped TiO2 and TiO2 respectively were able to degrade 56 and 14 . The potential bias was applied 0.2 V on the surface of the Ag N co doped TiO2 electrode, capable of increasing the PEC activity of MB degradation, gives PEC rate constants k 9x10 3. min 1 , which is 4.5 times faster than by photocatalysis PK without potential bias k 2x10 3.min 1 . Several factors affecting the PEC degradation of MB have been evaluated, ie optimum pH is 9.0 optimum potential bias of 0.2 V and initial concentration of optimum MB solution is 10 ppm. The Ag N co doped TiO2 electrode developed has a high stability of photocatalytic activity, at least 5 times the use still showing good photocatalytic activity so it is very economical to apply in degrading organic pollutants. "
2018
D2387
UI - Disertasi Membership  Universitas Indonesia Library
cover
Adrian Khrisna Muda
"Air merupakan salah satu kebutuhan utama bagi seluruh makhluk hidup di seluruh belahan muka bumi. Perkembangan dunia industri yang sangat pesat memberikan dampak yang serius terhadap lingkungan sekitar dimana aktivitas manusia sering menghasilkan pencemaran air sehingga menyebabkan turunya kualitas air. Oleh karena itu, pengelolaan terhadap kualitas air sangat diperlukan sebagai parameter untuk menjaga kestabilan kualitas air terhadap lingkungan sekitar. Pengukuran kebutuhan oksigen dalam air dapat dilakukan salah satunya dengan menggunakan metode COD dimana metode ini dilakukan dengan cara mengukur jumlah oksigen yang diperlukan untuk mengurai seluruh bahan organik yang terkandung dalam air. Salah satu metode pengukuran oksigen kimiawi dapat dilakukan dengan menggunakan metode fotoelektrokimia (Photoelectrocatalytic Chemical Oxygen Demand, PeCOD). Penelitian ini merupakan pengembangan dari metode yang sudah ada saat ini dalam penentuan nilai COD berbasis fotoelektrokatalisis. Sistem yang diusulkan saat ini adalah untuk menguji kekuatan arus cahaya photocurrent yang lebih baik dibandingkan penelitian sebelumnya. Proses penentuan nilai COD dilakukan menggunakan sistem batch yang berbasis metode fotoelektrokimia dengan cara mencelupkan elektroda yang terdiri dari elektroda counter yaitu dengan stainless steel dan elektroda kerja titanium dioksida berbentuk nanotube yang dibuat dari metode anodisasi pada 50V selama 1 jam. Senyawa yang digunakan adalah beberapa senyawa organik yang terdiri dari kalium hidrogen Ptalat (KHP), asam benzoat, fenol dan metanol dimana pengujian dengan sistem batch dapat bekerja secara optimal di konsentrasi yang rendah (10-200 ppm), namun tidak dapat bekerja secara optimal di konsentrasi yang tinggi (300-500 ppm). Selama proses pengukuran, terjadi proses reaksi degradasi senyawa organik pada permukaan elektroda kerja titanium dioksida nanotube menunjukan bahwa senyawa KHP memiliki arus serapan yang sangat besar dibandingkan senyawa organik lainnya. Hasil pengujian standar adisi dilakukan untuk mengamati perubahan arus cahaya akumulasi respon zat kimia seperti analit dan gangguan kimia. Hasil penelitian menunjukan bahwa terdapat beberapa senyawa yang memiliki persentase kesalahan relatif diatas 5% sehingga melebihi batas normal kesalahan dimana terdapat kurva kalibrasi yang kurang akurat. Penentuan metode fotoelektrokimia dengan sistem batch sebagai sensor COD diperoleh rentang nilai COD 0-70 mg/L dan mengindikasikan ketidakmampuannya dalam mendegradasi seluruh senyawa sampel selama waktu pengukuran 100 detik dari hasil plot grafik COD teoritis vs COD hasil percobaan. Hal tersebut dibuktikan dengan perbandingan metode bias antara metode konvensional dan metode fotoelektrokatalisis dengan persentase yang besar menggunakan sampel limbah air danau.

Water is one of the main needs for all human life in all parts of the earth. The rapid development of the industrial world seriously impacts the surrounding environment where human activities often cause water pollution, causing a decrease in water quality. Therefore, water quality management is vital as a parameter to maintain the stability of water quality in the surrounding environment. Water quality measurement with oxygen demand in water can be used by using the COD method, where this method is carried out by measuring the amount of oxygen needed to decompose all materials contained in water. One method of measuring chemical oxygen can be used by the photoelectrochemical method (Photoelectrocatalytic Chemical Oxygen Demand, PeCOD). This research is the further development of the existing methods for determining COD values based on photoelectrocatalysis. The current system proposed to test the strength of the photocurrent light current which is better than previous research. The process of determining the COD value is carried out using a photoelectrochemical method based on a batch system by dipping electrodes consisting of counter electrode, namely stainless steel, and a working electrode in the form of titanium dioxide nanotubes made from the anodization method at 50V for 1 hour. The compounds used are several organic compounds consisting of potassium hydrogen phthalate (KHP), benzoic acid, phenol, and methanol where testing with a batch system can work optimally at low concentrations (10-200 ppm) but cannot work optimally at high concentrations (300-500 ppm). During the measurement process, a degradation reaction of organic compounds occurs on the surface of the titanium dioxide nanotube working electrode, this shows that the KHP compound has a large absorption current compared to other organic compounds. The result of the standard addition test was carried out to observe changes in the light current accumulation of chemical responses such as analyst and chemical interference. The result shows that several compounds had a relative error percentage above 5% so organic compounds exceeded the normal error limit and had a less accurate calibration curve. Determination of the photoelectrochemical method with a batch system as a COD sensor obtained a COD value range 0-70 mg/L and indicates its ability to degrade all sample compounds during a measurement time of 100 seconds from the result of the theoretical COD vs experimental graph plot. This is proven by comparing the bias methods between the conventional method and the photoelectrocatalysis method with a large percentage using lake water sample waste."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Nurhayati Indah Ciptasari
"Dalam beberapa tahun terakhir, peningkatan pesat teknologi telah mendorong pengembangan berbagai jenis material di bidang ilmu pengetahuan dan penelitian. Salah satu material yang paling populer untuk penelitian adalah reduced Graphene Oxide (rGO). Material dibuat dari Graphene Oxide (GO) dengan melakukan berbagai metode pengolahan kimia dan termal untuk mengurangi kandungan oksigen di dalamnya. Sifat-sifat luar biasa dari rGO seperti sifat termal, mekanik, dan elektronik menjadikannya sebagai kandidat bahan yang potensial digunakan dalam berbagai aplikasi dengan penambahan matriks untuk memperluas penggunaannya. Penelitian ini bertujuan untuk mengembangkan kemungkinan material nanokomposit reduced Graphene Oxide (rGO) untuk aplikasi fotokatalitik yang lebih ramah lingkungan serta pengembangan material nanokomposit reduced Graphene Oxide (rGO) untuk aplikasi superkapasitor. Penelitian dilakukan dengan beberapa tahapan. Pertama dengan membuat bahan baku reduced graphene oxide dari grafit dengan menggunakan metode Hummers modifikasi. Kemudian mensintesis rGO dengan AgNPs (Perak Nanopartikel) menggunakan metode hidrotermal in-situ dengan reduktor NaBH4. Setelah itu, dilakukan pengujian aktivitas fotokatalitiknya terhadap ion Pb untuk mengetahui kinerja efektivitas rGO/AgNPs fotokatalitik dan potensinya sebagai bahan fotokatalitik alternatif dalam pengolahan limbah. Selanjutnya sintesis nanokomposit rGO dengan ZrO2 (Zirkonia) dilakukan dengan metode hidrotermal in-situ menggunakan reduktor NaBH4. Kemudian dilakukan karakterisasi sifat fisik dan kimianya agar dapat diaplikasikan pada superkapasitor. Analisis dilakukan dengan menggunakan X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM), Spektroskopi Raman, Spektrofotometer UV-Vis, Fourier Transform Infra Red (FTIR), dan Electrochemical Impedance Spectroscopy (EIS). Hasil penelitian ini Sintesis nanokomposit rGO/AgNPs menggunakan metode hidrotermal in-situ dengan reduktor NaBH4 untuk menguji aktivitas fotokatalitiknya terhadap ion Pb berhasil dilakukan. Performa fotokatalitik dengan uji terhadap ion Pb didapatkan persentase maksimum sebesar 44% pada 1,5 jam iradiasi. Nanokomposit rGO/ZrO2 berhasil disintesis dengan metode hidrotermal in-situ menggunakan reduktor NaBH4. Nilai spesifik kapasitansi tertinggi sebesar 482 F/g diperoleh pada rGO-ZrO2 = 1:2 dengan menggunakan PANI dalam larutan elektrolit H2SO4 karena pada kondisi ini menghasilkan nilai resistansi yang rendah sebesar 238,53 ohm.  

In recent years, rapid advancements in technology have driven the development of various types of materials in the field of science and research. One of the most popular materials for research is reduced Graphene Oxide (rGO). This material is made from Graphene Oxide (GO) through various chemical and thermal processing methods to reduce its oxygen content. The outstanding properties of rGO, such as thermal, mechanical, and electronic properties, make it a potential candidate for use in various applications with matrix additives to expand its usage. This research aims to explore the potential of reduced Graphene Oxide (rGO) nanocomposite materials for environmentally friendly photocatalytic applications and the development of rGO nanocomposite materials for supercapacitor applications. The research is conducted in several stages. Firstly, raw materials of reduced graphene oxide are produced from graphite using a modified Hummers method. Then, rGO is synthesized with AgNPs (Silver Nanoparticles) using an in-situ hydrothermal method with NaBH4 as the reducing agent. Subsequently, the photocatalytic activity of the rGO/AgNPs composite is tested against Pb ions to evaluate its effectiveness and potential as an alternative photocatalytic material in wastewater treatment. Furthermore, the synthesis of rGO nanocomposites with ZrO2 (zirconium dioxide) is carried out using an in-situ hydrothermal method with NaBH4 as the reducing agent. The physical and chemical properties of the nanocomposites are characterized for their application in supercapacitors. Analysis is performed using X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM), Raman Spectroscopy, UV-Vis Spectrophotometry, Fourier Transform Infrared (FTIR) Spectroscopy, and Electrochemical Impedance Spectroscopy (EIS). The results of this research show the successful synthesis of rGO/AgNPs nanocomposites using an in-situ hydrothermal method with NaBH4 as the reducing agent to test their photocatalytic activity against Pb ions. The photocatalytic performance, tested against Pb ions, achieved a maximum percentage of 44% after 1.5 hours of irradiation. Additionally, the rGO/ZrO2 nanocomposites were successfully synthesized using the in-situ hydrothermal method with NaBH4 as the reducing agent. The highest specific capacitance value of 482 F/g was obtained at rGO-ZrO2 = 1:2 ratio, using PANI in the H2SO4 electrolyte solution, as this condition resulted in a low resistance value of 238.53 ohms."
Depok: Fakultas Teknik Universitas Indonesia, 2023
D-pdf
UI - Disertasi Membership  Universitas Indonesia Library
cover
Prita Amelia
"Amonia merupakan senyawa penting bagi kehidupan di bumi, diantaranya yaitu dalam bidang industri dan pertanian. Permintaan amonia diperkirakan akan meningkat setiap tahunnya. Secara konvensional, fiksasi industri dari N2 untuk menghasilkan NH3 dilakukan melalui proses Haber−Bosch yang membutuhkan kondisi suhu dan tekanan yang sangat ekstrim sehingga mengonsumsi energi dalam jumlah tinggi dan mengemisikan CO2 dalam jumlah yang sangat besar. Oleh karena itu, perlu mengembangkan teknologi alternatif untuk sintesis amonia dengan metode yang ramah lingkungan. Banyak penelitian yang mengembangkan konversi nitrogen menjadi amonia secara fotoelektrokimia dengan adanya material semikonduktor, namun efisiensi yang dihasilkan masih belum cukup baik, sehingga perlu untuk dikembangkan lebih lanjut. Pada penelitian ini dilakukan pengembangan sistem tandem Dye Sensitized Solar Cell-Photoelectrochemistry (DSSC-PEC) untuk konversi nitrogen menjadi amonia. Sel DSSC disusun menggunakan fotoanoda N719/TiO2NTs, elektrolit I-/I3-, dan katoda Pt/FTO. Efisiensi DSSC yang dihasilkan pada penelitian ini sebesar 1,49%. Sel PEC disusun menggunakan BiOBr/TiO2NTs yang disintesis dengan metode successive ionic layer adsorption and reaction (SILAR) sebagai katoda, tempat berlangsungnya reaksi konversi nitrogen menjadi amonia, dan Ti3+/TiO2NTs sebagai fotoanoda tempat berlangsungnya oksidasi air. Selain itu, pada penelitian ini juga dilakukan variasi ketika Ti3+/TiO2NTs digunakan sebagai fotoanoda dan BiOBr/TiO2NTs sebagai katoda beserta BiOBr/TiO2NTs sebagai fotoanoda dan katoda. Sistem tandem disusun dengan menghubungkan anoda PEC dengan katoda DSSC, serta katoda PEC dengan anoda DSSC menggunakan kawat tembaga. Kadar amonia yang dihasilkan dianalisis dengan menggunakan metode fenat. Pada penelitian ini diperoleh kadar amonia tertinggi dengan sistem yang menggunakan material BiOBr/TiO2NTs pada anoda dan katoda dengan kadar amonia yang dihasilkan sebesar 0,1272 µmol selama 6 jam, dengan persen solar to chemical conversion (SCC) sebesar 0,0021%.

Ammonia is an important compound for human’s life, including in industry and agriculture. The demand for ammonia is expected to increase every year. Conventionally, the industrial fixation of N2 to NH3 is carried out through the Haber−Bosch process which requires extreme conditions of temperature and pressure. This process consumes a high amount of energy and emits a very large amount of CO2. Therefore, it is necessary to develop alternative technologies for ammonia synthesis using environmentally friendly methods. Many studies have developed the photoelectrochemical conversion of nitrogen to ammonia in the presence of semiconductor materials, but the resulting efficiency is still not good enough, so it needs further development. In this research, the development of the tandem system of Dye Sensitized Solar Cell-Photoelectrochemistry (DSSC-PEC) was carried out for the conversion of nitrogen to ammonia. DSSC cells were prepared using N719/TiO2NTs photoanode, I-/I3- electrolyte, and Pt/FTO cathode. The DSSC efficiency produced in this research is 1.49%. PEC cells were prepared using BiOBr/TiO2NTs synthesized by the successive ionic layer adsorption and reaction (SILAR) method as the cathode, where the reaction of converting nitrogen into ammonia takes place, and Ti3+/TiO2NTs as the photoanode where water oxidation takes place. In addition, in this study we also did the various experiments when Ti3+/TiO2NTs were used as photoanode and BiOBr/TiO2NTs as cathode, as well as BiOBr/TiO2NTs as photoanode and cathode. The tandem system is arranged by connecting the PEC anode to the DSSC cathode and the PEC cathode to the DSSC anode using copper wire. The resulting ammonia levels were analyzed using the phenate method. In this study, the highest ammonia levels were obtained with a system using BiOBr/TiO2NTs material at the anode and cathode with the resulting ammonia of 0.1272 µmol for 6 hours, with an solar to chemical (SCC) value of 0.0021%."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2022
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Aditya Rahman
"ABSTRAK
Senyawa semikonduktor oksida menjadi salah satu bahan yang paling banyak digunakan pada saat ini dalam upaya mengatasi polusi cairan dengan teknik fotokatalisis. Dalam penelitian ini telah dilakukan investigasi untuk mengetahui pengaruh ukuran partikel ZnO terhadap performa fotokatalisis. Sampel yang digunakan adalah ZnO yang telah tersedia secara komersial dengan variabel ukuran nano, mikro, sampai hasil perlakuan ballmill. Hasil difraksi XRD menunjukkan sampel ZnO mikro dengan perlakuan ballmill frekuensi 20 Hz memiliki ukuran kristalit yang paling besar (85,06 nm) dengan nilai energi celah pita yang paling kecil (3,16 eV), sampel ZnO nano kode NN memiliki ukuran kristalit terkecil (22,34 nm), dan sampel ZnO nano kode NA memiliki nilai energi celah pita yang paling besar (3,25 eV). Studi literatur menunjukkan hasil yang relevan dengan karakterisasi eksperimental yang didapat memberikan kesimpulan bahwa sampel ZnO mikro dengan kode M2 memiliki performa fotokatalisis terbaik diantara sampel lainnya.

ABSTRACT
Semiconductor Oxide compound has currently become one of the most widely used materials for liquid pollutant degradation through photocatalytic technique. In this study, investigation was conducted to determine the effect of ZnO particle size on its photocatalysis performance. The samples used were ZnO which are commercially available with nano, micro, and those of ball mill treated to reduced the size. The XRD diffraction results showed that the ZnO sample with 20 Hz frequency ballmill treatment had the largest crystallite size of 85.06 nm with the smallest bandgap energy value of 3.16 eV, while the ZnO sample in nanometer code NN had the smallest crystallite size of 22.34 nm, and another nano ZnO (code NA) had the largest band gap energy value of 3.25 eV. The literature study has shown that the characterization results of ZnO micro samples (code M2) had the best photocatalytic performance than other samples."
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Sylvia Yusim
"Alat perangkap nyamuk dengan bentuk unik yang juga berfungsi sebagai alat purifikasi udara ruang telah dirancang di dalam penelitian ini. Secara umum, alat ini terdiri dari lampu UV, panel berbahan aluminium, dan kipas penyedot. Panel aluminium dilapisi dengan kombinasi fotokatalis TiO2 dan adsorben karbon aktif AC melalui metode penyemprotan.
Hasil pengujian kinerja alat dalam menangkap nyamuk menunjukkan bahwa panel yang dilapisi fotokatalis jauh lebih efektif dalam menarik nyamuk dibandingkan panel yang tidak dilapisi fotokatalis. Dalam mendegradasi dua model polutan udara ruang yakni gas toluena dan asetaldehida, panel yang berlapis TiO2-AC lebih efektif dibandingkan dengan panel tanpa karbon aktif. Kombinasi proses yang mengintegrasikan adsorpsi dan fotokatalisis sangat menjanjikan untuk diterapkan pada alat perangkap nyamuk fungsi ganda ini.

Unique mosquito trap device which also have air purifier function has been constructed. Basically, the device consists of UV lamps, aluminum panel, and suction fan. The composite of TiO2 photocatalyst and activated carbon (AC) adsorbent were coated to panel by spray coating method.
Results show that panel coated by photocatalyst is more effective in trap the mosquitoes compare to uncoated panel. Removal of two models of indoor organic pollutant, toluene and acetaldehyde, is also more effective when using TiO2-AC as panel compare to TiO2 panel only.
"
Depok: Fakultas Teknik Universitas Indonesia, 2008
S52223
UI - Skripsi Open  Universitas Indonesia Library
cover
Faiza Ramadhina Kuncara
"Fotokatalis (M = Ni, Cu, Zn)/TiO2/g-C3N4 disiapkan menggunakan metode wet impregnation dengan memvariasikan konsentrasi setiap jenis logamnya. Variasi jenis logam dan komposisinya dipelajari untuk melihat pengaruhnya terhadap degradasi limbah farmasi antibiotik, Ciprofloksasin. Analisis karakterisasi katalis dan produk dilakukan dengan UV-Vis, UV-Vis Diffuse Reflectance Spectroscopy (UV-Vis DRS), dan Fourier Transform Infrared Spectroscopy (FTIR). Dari hasil karakterisasi didapatkan nilai band gap terkecil sebesar 2.4 eV pada katalis (2) Zn/TiO2/g-C3N4. Uji degradasi Ciprofloksasin dilakukan di dalam fotoreaktor dengan penyinaran internal menggunakan lampu UV 20 Watt. Hasil degradasi dengan kalsinasi gas nitrogen pada variasi logam nikel terbaik sebesar 17% pada katalis (2) Ni/TiO2/g-C3N4, variasi logam tembaga terbaik sebesar 26% pada katalis (4) Cu/TiO2/g-C3N4, dan variasi logam seng terbaik sebesar 28% pada katalis (2) Zn/TiO2/g-C3N4.

Photocatalysts (M = Ni, Cu, Zn)/ TiO2/g-C3N4 were prepared using wet impregnation method by varying the concentration of each metal type. The variation of metal type and its composition was studied to see its effect on the degradation of pharmaceutical waste antibiotic, Ciprofloxacin. Characterization analysis of the catalyst and product was carried out by UV-Vis, UV-Vis Diffuse Reflectance Spectroscopy (UV-Vis DRS), and Fourier Transform Infrared Spectroscopy (FTIR). From the characterization results, the smallest band gap value of 2.4 eV was obtained on (2) Zn/TiO2/g-C3N4 catalyst. Ciprofloxacin degradation test was conducted in a photoreactor with internal irradiation using a 20 Watt UV lamp. The degradation results with nitrogen gas calcination on the best nickel metal variation was 17% on (2) Ni/TiO2/g-C3N4 catalyst, the best copper metal variation was 26% on (4) Cu/TiO2/g-C3N4 catalyst, and the best iron metal variation was 28% on (2) Zn/TiO2/g-C3N4 catalyst."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Fauziah Fitri Ramadhani
"Peningkatan penduduk dunia sebanding dengan kebutuhan pemenuhan energi dalam kehidupan sehari-hari. Gas CO2 masih menjadi kontributor efek rumah kaca dan peningkatan suhu bumi. Riset terus dilakukan sebagai upaya mengatasi permasalahan tersebut dengan tetap mempertimbangkan pemenuhan kebutuhan energi dunia. Photoelectrochemistry (PEC) atau sel fotoelektrokimia merupakan salah satu metode yang banyak dikembangkan karena menawarkan kondisi reaksi pada suhu dan tekanan lingkungan sehingga minim emisi dan hemat biaya operasional. Dengan prinsip kerja sel fotoelektrokimia yang menyerap energi dari sinar matahari dan mengubahnya menjadi spesi bermuatan, peneliti melihat potensi konversi gas CO2 menjadi energi baru yang lebih bermanfaat. Penelitian ini berfokus pada konversi gas CO2 menjadi metanol dengan menggunakan elektroda blue-TiO2 nanotube arrays yang dilapisi kobalt fosfat (TNA)/CoPi. TiO2 merupakan material yang bersifat stabil, murah, dan ramah lingkungan, namun memiliki kelemahan pada energi celah pitanya yang lebar (3,2 eV) sehingga hanya aktif di bawah sinar UV. Modifikasi dilakukan untuk mengubah TiO2 menjadi black-TNA dan blue-TNA yang berfasa anatase dan blue-TNA/CoPi yang memiliki konduktifitas, kemampuan absorbansi sinar tampak, dan aktivitas fotoelektrokimianya yang lebih baik. Rancangan sistem fotoelektrokimia terdiri dari blue-TNA/CoPi sebagai fotoanoda, black-TNA sebagai katoda, dan Ag/AgCl sebagai elektroda pembanding. Selama proses fotoelektrokimia, diberikan eksternal bias potensial dengan variasi potensial -0,0214 V, -0,2714 V, dan -0,5214 V vs. RHE. Dengan konfigurasi sel dan kondisi operasi dalam penelitian ini, diperoleh hasil konversi metanol terbaik pada pengaruh potensial eksternal sebesar -0,5214 V sebesar 2,996 µmol.

The growing world population increases the energy demand. However, increasing energy consumption also produces pollution, and CO2 mainly contributes to the greenhouse effect and increases the earth’s temperature. Therefore, this study strives to overcome these problems while considering the world’s energy demand. Photoelectrochemical cell (PEC) is a method that has been widely developed because it offers reaction at standard temperature and pressure, resulting in minimal emissions and reduced operational costs. With the principle of photoelectrochemical cells that absorbs energy from sunlight and converts it into charged chemical species, the researchers found the potential for converting CO2 gas into more usable renewable energy. This research aims to convert CO2 gas into methanol using blue-TiO2 nanotube arrays (TNA)/CoPi electrodes. TiO2 is a stable, inexpensive, and environmentally friendly material with a weakness in its wide bandgap characteristic (3.2 eV), which makes it only active under UV light. Modifications were conducted to convert TiO2 into black-TNA, blue-TNA, and blue-TNA/CoPi, which have better conductivity and photoelectrochemical activity under visible light. The design of the photoelectrochemical system consists of blue-TNA/CoPi as the photoanode, black-TNA as the cathode, and Ag/AgCl as the reference electrode. During the photoelectrochemical process, an external bias potential is applied with potential variations of -0.0214 V, -0.2714 V, and -0.5214 V vs. RHE. With the cell configuration and operating conditions, this study found that the best methanol conversion results were obtained at the influence of an external potential of -0.5214 V of 2.996 µmol."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>