Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 172265 dokumen yang sesuai dengan query
cover
Yosi Kusuma Eriwati
"ABSTRAK
Telah dilakukan penelitian untuk mengetahui efek perlakuan panas melalui
pemanasan fumace dan radiasi Nd:YAG Iaser terhadap perubahan mikrostruktur,
kekerasan mikro dan morfologi permukaan dentin manusia sebagai modifikasi
permukaan dentin. Dengan menggunakan sampel dentin dari gigi impaksi molar
3, perubahan energi panas yang berhubungan dengan transformasi fisik dan
khemis sebagai fungsi suhu menunjukkan kurva endotermik pada 111,62 °C
yang mengindikasikan kristalinitas yang Iebih rendah pada dentin dengan kristal
yang tidak homogen. Hasil DSC dentin menunjukkan kurva endotermik pada 40
°C - 284 "C, dan puncak eksotermik teriihat pada 500 °C. Total kehilangan berat
dentin dengan analisa TG adalah 21 ,26% setelah pemanasan 900 °C. Hasil XRD
pada suhu di atas 750 °C memperlihatkan puncak difraksi dari hidroksiapatit yang
meningkat dengan intensitas yang Iebih tinggi dengan munculnya puncak
Whitlockite. Perhitungan ukuran kristalit dentin yang bertambah besar
menunjukan adanya pertumbuhan kristalit akibat perlakuan panas sehingga
kristalinitas dentin berubah mendekati kristalinitas hidroksiapatit email. Nilai
kekerasan mikro Vickers jug meningkat akibat energi radiasi laser sesuai
dengan meningkatnya intensitas puncak difraksinya. Setelah radiasi Nd:YAG
laser terbentuk kawah dengan permukaan dentin yang meleleh dan mengalami
rekristalisasi. Jadi perilaku dentin manusia memperlihatkan perubahan fisik dan
khemis terhadap kenaikan suhu pemanasan dan energi radiasi laser yang tinggi.
Efek panas menyebabkan perubahan mikrostruktur dan sifat kekerasan yang
meningkat mendekati struktur dan kekerasan email.

Abstract
The purpose of this study was to investigate the effects of heat treatment
and Nd:YAG laser irradiation on the microstructure, microhardness and
morphological changes of human dentin surfaces for alternative dentin surface
modification. The results on the DSC of dentin show a large endothermic curve at
40°C to 284°C, likewise the DTA endothermic peak at 111,62 °C which
represent a material of less crystallinity and inhomogenous crystals. An
exothermic peak was also shown at 500ºC by DSC. The total loss of dentin
weight by TG analysis was 21.26% after heated to 900°C. XRD investigation
revealed that at higher temperature (above 750 °C) the amount of diffraction
peaks of hydroxyapatite were higher and more intense with the development of
Whitlockite. The crystallite size were also higher showing crystal growth upon
heat-treatment. After Nd:YAG laser-treated, dentin with relatively low
crystallinities obtains a structure which comes to resemble the crystalline
structure of enamel hydroxyapatite. VIckers micro-hardness property on lased
dentin surfaces showed increasing values of all laser exposures that were
associated with the increase intensity of peak diffraction. SEM observations on
Nd:YAG laser irradiation on dentin surface resulted in creater formation at higher
energy output, as well as surface melting, recrystallized and glazed surfaces. The
thermal behavior of human dentin shows physical and chemical changes with
higher temperature and higher energy output of Nd:YAG laser treatment.
Thermal effects caused microstructure and morphological changes on dentin
surfaces with increased microhardness surface properties which resemble the
microstructure and hardness of enamel."
2003
D1224
UI - Disertasi Membership  Universitas Indonesia Library
cover
Sherly A. Dien
"Pengukuran kadar oksigen terlarut (DO) dalam perairan merupakan salah satu parameter dalam monitoring kualitas air. Pengukuran kadar DO dengan basis elektrokimia telah banyak dikembangkan diantaranya dengan menggunakan elektroda GC termodifikasi nanopartikel Au. Namun, elektroda GC termodifikasi nanopartikel Au dapat mengalami penurunan respon pengukuran berulang oleh karena itu diperlukan elektroda yang permukaannya selalu terbarukan sehingga dapat dikembangkan sebagai elektroda disposable. Studi modifikasi permukaan plastik dengan nanopartikel Au telah dilakukan. Nanopartikel Au dengan zat penstabil sitrat dan dodekanatiol disintesis dengan menggunakan zat pereduksi NaBH4 digunakan untuk memodifikasi permukaan plastik dengan cara merendam plastik ke dalam campuran dodekanatiol, larutan nanopartikel Au dan air dengan pengadukan kuat selama 24 jam pada temperatur ruang. Karakterisasi dengan TEM menunjukan, ukuran nanopartikel Au diperoleh diameter 5-10 nm. Namun, hasil karakterisasi permukaan plastik termodifikasi dengan SEM menunjukan bahwa permukaan termodifikasi oleh nanopartikel Au berukuran lebih dari 100 nm. Pengukuran respon arus dilakukan dengan teknik siklik voltametri dengan daerah pemindaian -1000mV hingga 0 mV diperoleh penurunan arus reduksi seiring dengan meningkatnya kadar O2 mengindikasikan bahwa plastik mika termodifikasi dapat digunakan sebagai sensor oksigen.

Abstract
Measurement of dissolves oxygen (DO) in water is one of the parameters in water quality monitoring. Measurement of DO levels on the basis of electrochemistry has been develoved among others by using GC electrode modified with Au nanoparticles. However, Au nanoparticles modify on GC electrode decreased response to repeated measuremen. Therefore, electrode surface should be always renewable surface so that it can be developed as a disposable electrode. Study of plastic surface modification with Au nanoparticles have been performed. Au nanoparticles stabilized by citrate and dodecanathiol substance synthesized by using NaBH4 as reducing agent used to modify plastic surface of by soaking with strong stirring for 24 hous in room temperature. Characterization TEM shows, the size of Au nanoparticles obtained a diameters 5-10 nm. However, SEM characterization of plastic surface modified by instrument showed that particles on plastic surface modified is larger than 100 nm. Plastic modified nanoparticle Measurement of current response was done by using cyclic voltametry by scanning the range potential 1000mV to 0 mV. The reduction current was decreased with increasing O2 levels. It indicate that plastic can be used as oxygen sensor."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2011
S207
UI - Skripsi Open  Universitas Indonesia Library
cover
Ari Antono
"Insulasi panas merupakan material yang penting dalam industri untuk menunjang efisiensi suatu proses sistem. Pada penelitian ini dilakukan pembuatan komposit dengan menggunakan epoksi Interzinc®52 sebagai matriks dan material zirkonia sebagai penguat. Proses pembuatan komposit dengan menggunakan metode pengaduk mekanis dengan kondisi waktu pengadukan 5 menit dan 15 menit. Material substrat yang digunakan adalah baja karbon ASTM A36 dengan ukuran 50 mm x 50 mm x 5 mm. Persen berat (wt%) untuk material zirkonia digunakan dengan Persen 5% (wt%), 10% (wt%) dan 15% (wt%) pada 50 ml epoksi, ketebalan lapisan insulasi 1 mm, 3 mm dan 5 mm. Pengujian dilakukan untuk mengetahui sifat termal dan sifat mekanis dari komposit yang terbentuk terdiri dari X-ray diffraction analysis, scanning electron microscopy, heat loss, thermogravimetric analysis, hardness shore D. Hasil pengujian menunjukkan bahwa penambahan kadar ZrO2 ke dalam epoksi dan kenaikan ketebalan lapisan dapat menghasilkan lapisan insulasi panas dengan stabilitas termal yang lebih baik dan menurunkan PRH (percentage of residual heat). Selain itu nilai kekerasan permukaan naik seiring bertambahnya ZrO2 di dalam epoksi, hal ini disebabkan adanya kenaikan kerapatan dalam struktur mikro. Sementara itu, semakin lama waktu pengadukan meningkatkan nilai kekerasan dan kemampuan lapisan komposit dalam menahan panas yang hilang ke permukaan. Dari penelitian ini di peroleh PRH terendah 64% dan nilai kekerasan tertinggi 36 HD pada sampel epoksi dengan campuran 15% ZrO2 pada ketebalan 5 mm setelah pengadukan selama 15 menit.

Nowadays, Heat insulation is an important material in industry to support the efficiency of a system process. In this study, composites were made using epoxy Interzinc®52 as matrix and zirkonia material as reinforcement. The process of making composites using the mechanical stirring method with a stirring time of 5 minutes and 15 minutes. The substrate material used is ASTM A36 carbon steel with a size of 50 mm x 50 mm x 5 mm. Weight percentage (wt%) for zirkonia material used with percentages of 5% (wt%), 10% (wt%) and 15% (wt%) in 50 ml Epoxy, insulation layer thickness 1 mm, 3 mm and 5 mm. Tests were carried out to determine the thermal and mechanical properties of the composites, consisting of X-ray diffraction analysis, scanning electron microscopy, heat loss, thermogravimetric analysis, hardness shore D. The test results show that the addition of ZrO2 content into the epoxy and the increase in layer thickness can produce a heat insulation layer with better thermal stability and reduce PRH (percentage of residual heat). In addition, the surface hardness value increases with the addition of ZrO2 in the Epoxy, this is due to an increase in density in the microstructure. Meanwhile, the longer stirring time increases the hardness value and the ability of the composite layer to withstand heat loss to the surface. From this study, the lowest PRH value was 64% and the highest hardness value was 36 HD on the Epoxy sample with a mixture of 15% ZrO2 at a thickness of 5 mm after stirring for 15 minutes."
Depok: Fakultas Teknik Universitas Indonesia, 2021
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
JPK 17(4-6)2011
Artikel Jurnal  Universitas Indonesia Library
cover
"Analisis potensi bahaya,dampak dan penanggulannya terhadap penggunaan perangkat renograf hasil litbangyasa BATAN telah dilakukan. Setiap pemanfaatan peralatan perlu kepastian bahwa alat aman untuk dioperasikan....."
Artikel Jurnal  Universitas Indonesia Library
cover
Bobi Eka Putra
"Pada zaman sekarang perkembangan teknologi berkembang pesat. Adanya modifikasi material perovskite berbasis manganit telah diteliti untuk diterapkan pada Colossal Magnetoresistance. Penelitian yang telah dilakukan mengenai struktur mikro dan sifat magnetik material perovskite manganites La0.67Sr0.33Mn1-xZnxO3 (x= 0; 0,15; 0,2; 0,4) yang disintesis dengan metode solid state bertujuan untuk melihat pengaruh yang ditimbulkan Zn pada material La0.67Sr0.33Mn1-xZnxO3 (x= 0; 0,15; 0,2; 0,4) berupa struktur morfologi dan sifat kemagnetannya. Karakterisasi XRD menunjukan bahwa struktur kristal material berbentuk rhombohedral pada space group R-3c dengan rata-rata ukuran kristal 106 nm, 103 nm, 101 nm dan 96 nm. Karakterisasi SEM dan EDS menunjukan perubahan ukuran grain dan memperlihatkan keberadaan unsur Zn sebagai pendoping. Ukuran grain mengecil seiring bertambahnya konsentrasi Zn dengan rata-rata ukuran grain 148 nm, 134 nm, 127 nm dan 117 nm. Karakterisasi VSM menunjukan kurva histeresis yang memperlihatkan material bersifat feromagnetik ketika 0 ≤ x < 0,2 dan berubah menjadi paramagnetik ketika x > 0,2 yang terlihat dengan menurunnya nilai magnetisasi dari 65,1 emu/gram, 14,4 emu/gram, 8,2 emu/gram dan 1,7 emu/gram.

In this day and age, technological development is developing rapidly. The existence of modifications to manganese-based perovskite materials has been studied to be applied to Colossal Magnetoresistance. Research that has been conducted on the microstructure and magnetic properties of manganites perovskite material La0,67Sr0,33Mn1-xZnxO3 (x= 0; 0.15; 0.2; 0.4) synthesized by the solidstate method aims to see the influence that Zn has on the material La0,67Sr0,33Mn1-xZnxO3 (x= 0; 0.15; 0.2; 0.4) in the form of morphological structure and magnetisme properties. XRD characterization shows that the crystal structure of rhombohedral-shaped materials in the R-3c space group with an average crystal size of 106 nm, 103 nm, 101 nm and 96 nm. SEM and EDS characterizations show a change in grain size and show the presence of Zn elements as doping. Grain size decreases as Zn concentration increases with average grain sizes of 148 nm, 134 nm, 127 nm and 117 nm. VSM characterization shows a hysteresis curve that shows the material is ferromagnetic when 0 ≤ x < 0.2 and turns paramagnetic when x > 0.2 which is seen by decreasing the magnetization value of 65.1 emu/gram, 14.4 emu/gram, 8.2 emu/gram and 1.7 emu/gram."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
"Isolation of charantin from the extract of Momordica charantia L and validation of TLC densitometry for the determination of charantin has been done....."
Artikel Jurnal  Universitas Indonesia Library
cover
"Multi-protocol label switching (MPLS) has become an attractive technology of choice for internet backbone service provider. MPLS features the ability to perform traffic engineering and provides support for quality of service traffic provisioning....."
Artikel Jurnal  Universitas Indonesia Library
cover
Sesmaro Max Yuda
Depok: Fakultas Teknik Universitas Indonesia, 1994
S41052
UI - Skripsi Membership  Universitas Indonesia Library
cover
Sunarno
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2003
T40019
UI - Tesis Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>