Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 107447 dokumen yang sesuai dengan query
cover
Djoko Sumaljo
"Salah satu sektor industri yang memberikan kontribusi adalah industri perminyakan. Industri ini selain memberi dampak positif, juga menimbulkan dampak negatif berupa limbah diantaranya lumpur dari pengeboran.
Ada dua jenis Lumpur yang dipakai yaitu oil base mud dan water base mud. Berat jenis lumpur merupakan fungsi utama untuk menahan tekanan dari bawah tanah supaya tidak terjadi semburan liar. Untuk mendapatkan berat jenis tersebut harus digunakan bahan kimia yang mempunyai kandungan logom berat.
Rumusan permasalahan yang dapat disusun adalah sebagai berikut:
1. Apakah dengan mengubah penerapan konsep teknologi water base mud menjadi oil base mud dalam kegiatan pengeboran minyak lepas pantai, beban limbah berupa air lumpur buangan dapat dikurangi karena lumpur masih tetap dapat dipakai untuk pengeboran berikutnya?
2. Apakah penerapan konsep pengurangan komponen aditif dari sumber dalam kegiatan pengeboran minyak bumi di lepas pantai dapat menimbulkan dampak kemungkinan terjadinya semburan liar dan memberikan dampak manfaat bagi industri perminyakan tersebut yaitu berkurangnya beban limbah yang dihasilkan?
3. Apakah penerapan konsep minimisasi limbah dalam kegiatan pengeboran minyak bumi di lepas pantai tersebut di atas dapat meningkatkan efisiensi biaya produksi bagi industri perminyakan?
4. Apakah kegiatan pengeboran minyak lepas pantai di daerah operasi minyak lapangan Maxus mempunyai pengaruh dampak negatif terhadap kualitas air laut dan dampak positif langsung terhadap persepsi masyarakat sekitarnya?
Tujuan penelitian ini adalah:
1. Untuk mengetahui pengaruh pengurangan penggunaan bahan kimia (aditif) pada lumpur pengeboran terhadap kualitas limbah yang dihasilkan dan kemungkinan terjadinya semburan liar.
2. Untuk mengetahui pengaruh penerapan perubahan media air menjadi media minyak dalam pembuatan lumpur terhadap beban limbah yang dihasilkan setelah operasi Pengeboran.
3. Untuk mengetahui pengaruh penerapan konsep minimisasi limbah dalam kegiatan pengeboran minyak bumi di lepas pantai terhadap tingkat efisiensi biaya produksi pada industri perminyakan.
4. Untuk mengetahui pengaruh kegiatan operasi pengeboran minyak lepas pantai di daerah operasi minyak lapangan Maxus terhadap kualitas air laut dan terhadap persepsi masyarakat sekitarnya.
Hipotesis dalam penelitian ini adalah:
1. Pengurangan penggunaan bahan kimia (aditif) pada lumpur Pengeboran akan mengurangi bahaya limbah yang dihasilkan serta mengurangi resiko terjadinya semburan liar.
2. Penerapan perubahan media air menjadi media minyak dalam pembuatan lumpur akan menurunkan beban limbah yang dihasilkan setelah operasi Pengeboran.
3. Penerapan konsep minimisasi limbah dalam kegiatan pengeboran minyak bumi di lepas pantai akan meningkatkan efisiensi biaya produksi pada industri perminyakan.
4. Kegiatan operasi pengeboran minyak lepas pantai di daerah operasi minyak lapangan Maxus menimbulkan dampak menurunnya kualitas air laut dan persepsi negatif masyarakat sekitarnya.
Jenis penelitian ini merupakan penelitian kuantitatif dengan metode survei dan ekspos fakto. Penelition ini dilakukan di daerah operasi wilayah Maxus di Laut Jawa dan berlangsung selama kurang lebih 6 bulan, yaitu sejak Desember 2001 - Juni 2002.
Tahapan penelitian meliputi penentuan jenis penelitian yaitu penelitian kuantitatif dengan metode survei dan ekspos fakto, penentuan lokasi penelitian yaitu di daerah operasi Maxus, penentuan rancangan penelitian yang meliputi variabel penelitian. tahapan penelitian, pengumpulan data, dan analisis data serta, perencanaan upaya minimisasi limbah lumpur dari sumbernya.
Secara umum parameter kualitas badan air masih berada pada kisaran di bawah baku mutu dengan dijumpai beberapa unsur logam berat Ni, Cd dan Pb yang masih di atas ambang baku mutu. Keberadaan ketiga unsur logam berat tersebut meskipun masih di atas baku mutu tetapi belum terlihat pengaruhnya terhadap kehidupan biota laut.
Dari survey tentang pengaruh kegiatan operasi Pengeboran terhadap persepsi masyarakat, ternyata disimpulkan bahwa persepsi masyarakat terhadap kegiatan tersebut positif. Dengan kondisi tekanan awal dan akhir yang berbeda, secara prinsip bila penggunaan berat jenis lumpur pada operasi Pengeboran terlalu besar kemungkinan terjadi hilang lumpur sangat besar. Bila terjadi kehilangan lumpur maka kemungkinan terjadinya semburan liar sangat besar.
Secara prinsip, volume limbah yang dibuang di lingkungan pada media water base mud lebih besar bila dibandingkan dengan memakai media oil base mud.
Kesimpulan peneliiian ini adalah:
1. Pemakaian oil base mud dapat mengurangi jumlah volume pembuangan limbah lumpur, karena lumpur bekas oil base mud masih dapat digunakan kembali.
2. Penurunan berat jenis sesuai dengan penurunan tekanan formasi akan .mengurangi jumlah pemakaian bahan kimia, terutama yang mengandung logam berat. sehingga dampak yang ditimbulkan juga makin berkurang. Penurunan jumlah bahan kimia akan menurunkan biaya operasi dan pengelolaan lingkungan.
3. Secara umum semua parameter kualitas badan air masih berada dalam batas baku mutu yang ditetapkan sehingga daerah wilayah operasi masih cukup baik. Tetapi beberapa komponen logam berat seperti Ni, Pb, dan Cd masih berada di atas baku mutu, namun secara berangsur ketiga unsur tersebut cenderung mengalami penurunan.
4. Penilaian masyarakat tentang kegiatan operasi minyak dan gas Maxus terhadap kehidupan kegiatan sosial ekonomi mereka ternyata positif baik.
5. Meskipun kualitas air dan persepsi masyarakat baik, tetapi perubahan parameter bawah tanah menghendaki penurunan berat jenis yang dipakai, karena pemakaian berat jenis yang tinggi memungkinkan terjadinya kehilangan lumpur. Bila hal tersebut terjadi, penahan tekanan formasi tidak ada sehingga akibatnya semburan liar dapat terjadi.

Minimizing Mud Waste in Offshore Oil Drilling (A case study at the Maxus Offshore Oil Drilling Platform in the Java Sea)One of the industrial sectors that provide considerable contribution has been petroleum industry. This industry brings out positive effect, and it also causes negative effect in the form of various sorts of waste including mud and sludge produced by the drilling activity.
There are two types of mud in use, oil base mud and water base mud. The specific gravity of the mud constitutes the prime function that is to restrain the underground pressure from surging up, and thus no wild spouts would occur. In order to obtain such specific gravity we must employ certain chemicals that have heavy metal content.
The formulation of the problematic questions can be practically arranged as follows:
1. Can the alteration made in the application of water base mud concept into that of oil base mud in the offshore oil drilling activity reduce the waste load that comprises muddy waste water, considering the fact that the application of oil base mud technology makes the mud remain potentially usable in the next drilling?
2. Can the application of concept on additive component reduction from the source in the offshore petroleum drilling activity raise possible effect that causes wild spouts, and will such application give beneficial effect to the oil industry, that is the decrease in the waste load produced?
3. Can the application of waste minimization concept in the offshore petroleum drilling activity as mentioned above improve the efficiency of production cost in the oil industry?
4. Is offshore oil drilling in the Maxus operation area viewed positively by the existing community in the vicinity of the project?
The objectives of the research are:
1. To know and understand the extent of the effect resulting from reducing the (additive) chemicals applied in the drilling mud to the quality of the waste produced, and to the possible occurrence of wild spouts.
2. To see the effect of change from the application of the water media into oil media in mud production, especially towards the waste load associated with the drilling operation.
3. To see the effect of waste minimization concept in the offshore oil drilling activity towards the level of the efficiency in production cost.
4. To observe the effect of Maxus offshore oil drilling operation activities to the sea water quality and to the community existing in the neighborhood.
The hypothesis in the present research includes:
1. Reduction in the use of (additive) chemicals in the drilling mud will mitigate the hazards of the waste produced, and to lessen the risk of wild spouts occurrence.
2. The change from water media into oil media in mud production eation will decrease the waste load associated with drilling operation.
3. The application of waste minimization in offshore petroleum drilling will improve the efficiency of production costs in the oil industry.
4. The offshore oil drilling activities in the Maxus field is detrimental to the sea water quality, and creates negative perception to the community.
This is a quantitative research conducted through survey and fact exposing method. The present research was conducted at the Maxus operations in the Java Sea, and took approximately 6 months, starting from December 2001 to June 2002.
The phases in the research cover the designation of the research type, which is to be a quantitative research with survey and fact exposing method, and the designation of the research site, namely the Maxus operation zone. The designation of the research arrangement covers research variables, research phases, data collection, and data analysis as well as planning the efforts to minimize the mud waste from the source.
In general, the water body quality lies in the range of being under quality standard with a number of heavy metals elements (Ni, Cd, and Pb) above the threshold limit value. Although, three heavy metal elements are above the standard value, their effect to the sea aquatic life is yet to be seen.
From the survey conducted on the negative influence brought about by the drilling operation to the local society's perception, it turns out that such community's perception toward the activity is favorably positive.
With the beginning and end pressure being different, it can be principally postulated that when the use of the mud's specific gravity at the drilling operation is excessively high it is very likely that the loss of the mud is substantially high. When such high loss of mud occurs it is very likely that a wild spout will occur.
In principle, the volume of waste entering is greater for the water base mud media compared to the oil base mud.
The conclusions of the present research are:
1. The application of oil base mud reduces the volume of the disposed mud waste, because the oil base mud media can be reused.
2. The decrease in the specific gravity will, in accordance with the decrease in the formation pressure, reduce the number of the chemicals in use, particularly of those that contain heavy metal. As a result, the environment impact will be less. Subsequently, the reduction of chemicals wed reduces the operating and environmental management costs.
3. For the most part, all water quality parameters are within the acceptable limit. This means that the environmental quality of the operation area is reasonably good. However, there are several heavy metal components such as Ni, Cd, and Pb that are above the threshold limit value. However, the quantity of these three elements tends to gradually go down.
4. The opinion of the local community on the oil and gas operation activities proves to be positive.
5. In spite of the good water quality and the favorable perception from the local people. The change in underground parameter necessitates a decrease in the mud specific gravity mud will potentially result in more mud loss. When this happens, wild spouts are bound to happen as there is not enough mud to counter the pressure."
Depok: Program Pascasarjana Universitas Indonesia, 2002
T 11055
UI - Tesis Membership  Universitas Indonesia Library
cover
Heraldus Panji Arikson
"Gangguan satu fasa ke tanah terjadi pada kabel bawah laut yang menghubungkan Pabelokan ke Nora. Gangguan ini seharusnya dapat segera diatasi oleh rele arus lebih pada penyulang Pabl – Nora dalam waktu 0,593 sekon. Akan tetapi, hal itu justru tidak terjadi dan malah menyebabkan seluruh area selatan, beberapa daerah area utara juga tengah mengalami pemadaman. Dalam skripsi ini, akan disimulasikan tiga kondisi arus gangguan yang berbeda – beda yaitu 397 A, 795 A dan 1,19 kA yang berasal dari kombinasi kontribusi arus gangguan oleh tiga generator yang bekerja. Ketidakseimbangan tegangan terjadi selama gangguan sehingga menyebabkan surge arrester pada G101B pecah. Kontribusi arus gangguan pun turun menjadi 397 A karena G101C memang tidak diaktifkan untuk bekerja. Nilai arus gangguan yang kecil ini membuat waktu tunda rele arus lebih IAC-53 pada feeder Pabelokan Nora beroperasi setelah 25 sekon. Nilai ini lebih lama daripada waktu yang dibutuhkan oleh rele SR489 untuk bekerja dengan nilai arus gangguan yang sama yaitu 8,31 sekon. Hal ini menyebabkan generator G101A lebih dahulu mengalami trip karena ground fault rele. Oleh karena itu, pengaturan nilai pick up arus gangguan dan waktu kerja rele pun harus diatur lebih cepat lagi yaitu pada kisaran 5 sekon untuk nilai arus yang sama agar kejadian serupa tidak terulang lagi.

Phase to ground fault happened to the subsea cable that connected Pabelokan to Nora. This fault should be cleared by Over c urrent relay at Pabl- Nora feeder in 0,593 second. Nevertheless, it didn’t work that way instead it caused all the south area and some of central and north area was shutdown. There will be three conditions of fault current that will be simulated on this simulation which are 397 A, 795 A and 1,19 kA that is coming from the combination of three generators that worked. The unbalanced voltage that happened when fault is inserted caused surge arrester in G101B blown up. The current fault decreased and it was 397 A because G101C was not work from the first, due to repairement. The fault current value that is so small caused delay in IAC-53 reay at Pabl-Nora feeder. This rele worked after 25 seconds. This value is longer than the time that SR489 relay needed to work at the exactly same fault current that is 8,31 seconds. It is caused generator G101A tripped by ground fault relay. As the solution, pick up current and time delay setting must be set faster that is about 5 seconds for the same value of current fault so this kind of things is not going to happened again.
"
Depok: Fakultas Teknik Universitas Indonesia, 2014
S56682
UI - Skripsi Membership  Universitas Indonesia Library
cover
Anggi Wibowo
"Salah satu parameter penting yang harus dicermati sebelum dilakukan pemboran sumur migas adalah besarnya tekanan di dalam formasi batuan yang akan dilakukan pemboran. Peristiwa kick, loss atau bahkan blowout pada lubang sumur dapat diantisipasi apabila prediksi tekanan pori dilakukan sebelum pemboran dimulai. Prediksi tekanan pori diperlukan untuk mendesain berat jenis lumpur yang digunakan dan lokasi kedalaman casing yang tepat untuk menghindari adanya overpressure pada lubang bor.
Tesis ini akan membandingkan tiga jenis metode yang biasa digunakan dalam perhitungan prediksi tekanan pori, yaitu: Metode Equivalent Depth, Metode Eaton, dan Metode Bowers. Ketiga metode tersebut akan dilakukan pada data yang berasal dari sumur dan data seismik dari area Delta Niger untuk melihat perbandingan diantaranya.
Hasil penelitian menunjukkan bahwa Metode Equivalent Depth dan Metode Eaton memiliki kemiripan hasil, karena menggunakan parameter input yang hampir sama namun algoritma yang berbeda. Metode Bowers menunjukkan hasil yang paling berbeda karena perhitungannya murni berdasarkan suatu persamaan empiris. Dari ketiga metode tersebut, untuk penelitian di area Delta Niger, Metode Equivalent Depth dan Metode Eaton dianggap paling baik untuk digunakan.

One important parameter that must be observed prior to the drilling of oil and gas wells is the amount of pressure inside the rock formations to be drilled. Events such as kick, loss, or even a blowout in the wellbore can be anticipated if the pore pressure prediction is made before drilling begin. Pore pressure prediction is required to design the density of mud used and the exact depth of right casing to avoid overpressure in the borehole.
This study will compare three types of methods used in the calculation of pore pressure prediction, which is: Equivalent Depth Method, Eaton Method, and Bowers Method. The three method will be performed on data derived from the well and seismic data from the Niger Delta area to see the comparison between them.
The results showed that the Equivalent Depth Method and Eaton Method have similar results due to the input parameters used are almost the same but with different algorithms. Bowers Method showed the most different results because the calculation is based purely on an empirical equation . Of the three methods, for research in the Niger Delta area, Equivalent Depth Method and Eaton Method are considered the best method to use."
Depok: Universitas Indonesia, 2015
T44080
UI - Tesis Membership  Universitas Indonesia Library
cover
Marsha Zharvania Almaira
"Pengeboran minyak dan gas bumi secara ilegal kerap terjadi di Indonesia, lantaran sudah menjadi budaya dan mata pencaharian tetap bagi masyarakat. Pengeboran yang dilakukan secara tanpa izin ini menimbulkan permasalahan, salah satunya adalah dampak lingkungan hidup berupa pencemaran dan kerusakan lingkungan. Permasalahan tersebut yang akan dibahas di dalam skripsi ini, yang meliputi dampak lingkungan hidup yang ditimbulkan oleh pengeboran minyak dan gas ilegal, pengaturan di Indonesia yang mengatur mengenai minyak dan gas serta lingkungan hidup, dan kebijakan yang dapat
mengoptimalkan ketentuan mengenai minyak dan gas yang telah ada. Metode yang digunakan dalam penelitian ini adalah yuridis-normatif dengan bahan pustaka berupa bahan hukum. Regulasi mengenai minyak dan gas bumi di Indonesia tercakup dalam tingkat konstitusi, peraturan perundang-undangan, peraturan pelaksanaan dan petunjuk teknis. Terlepas dari regulasi yang ada, ternyata belum cukup untuk menjangkau lebih dalam mengenai aspek minyak dan gas dikaitkan dengan perlindungan dari lingkungan hidup. Oleh karenanya sebagai usaha dalam mengatasi permasalahan tersebut, pemerintah dapat mengupayakan legalisasi dari pengeboran ilegal dengan pengeboran
dengan skala kecil yang dilakukan oleh masyarakat yang dilengkapi dengan pembinaan mengenai persyaratan lingkungan yang harus dipenuhi. Adapun pemerintah dapat menginterpretasi dan menafsirkan peraturan yang sudah ada terkait permasalahan ini,
seperti Peraturan Menteri Energi dan Sumber Daya Mineral Nomor 1 Tahun 2008 tentang Pedoman Pengusahaan Pertambangan Minyak Bumi pada Sumur Tua. Selain itu, diperlukan pembaharuan pada tataran peraturan baik di tingkat undang-undang maupun
peraturan pelaksana untuk beradaptasi dengan kebutuhan masyarakat di bidang pertambangan minyak dan gas bumi saat ini.

Illegal drilling in the oil and gas industry often occurs in Indonesia because it has become
a culture and permanent livelihood for the people living near the oil landmine. This illegal oil drilling being held without a permit raises problems, including environmental impact in the form of pollution and environmental damage to the region. Such issues will be discussed in this writing, such as the environmental impacts caused by oil and gas drilling, Indonesia's regulations about oil and gas and environmental protection and management, and policies that can optimize existing provisions regarding oil and gas. The method used in this study is normative juridical with legal materials in the form of literature. Regulations regarding oil and natural gas in Indonesia are covered at the constitutional level, statutory regulations, implementing regulations, and technical guidelines. Apart from the existing regulations, it is more is needed to go deeper into the aspects of oil and gas associated with environmental protection. Therefore, to overcome these problems, the government can seek the legalization of illegal drilling with small-scale drilling carried out by the community equipped with environmental guidance requirements that must be met. The government can interpret existing regulations related to this issue, such as Regulation of the Minister of Energy and Mineral Resources Number 1 of 2008 concerning Guidelines for the Oil Mining Business in Old Wells. In addition, reforms are needed at the regulatory level, both at the level of laws and implementing regulations to
adapt to the community's current needs in the oil and gas mining field.
"
Depok: Fakultas Hukum Universitas Indonesia, 2023
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
I Made Adi Wardana
"[ABSTRAK
Pengembangan lapangan gas laut dalam memiliki tantangan teknis, terkait fasilitas
produksi dan teknologi untuk dapat memproduksikan migas pada kondisi
lingkungan yang ekstrem. Disamping itu, biaya yang diperlukan lebih besar
dibandingkan pengembangan lapangan laut dangkal. Dalam penelitian ini
dilakukan analisa secara teknis dan ekonomis terhadap pengembangan lapangan
gas laut dalam di Selat Makasar dengan metode subsea tieback, dengan
memanfaatkan kapasitas tersedia dari floating production unit (FPU) yang sudah
ada. Analisa teknis meliputi penentuan ukuran pipa (flowline) optimal, yang dapat
memenuhi target deliverabilitas gas, memenuhi kriteria teknis lainnya, serta
analisa flow assurance, khususnya mitigasi hidrat untuk menjamin
keberlangsungan aliran fluida dari sumur bawah laut hingga ke titik jual. Dari
analisa teknis akan didapatkan beberapa konfigurasi ukuran pipa dan mitigasi
hidrat. Analisa ekonomi meliputi perhitungan biaya investasi untuk setiap opsi
yang memenuhi kriteria teknis, kemudian dilanjutkan penghitungan parameter
keekonomian berdasarkan aturan Production Sharing Contract (PSC) yang
berlaku di Indonesia. Dengan harga gas 6 US$/mmbtu, didapatkan nilai
Government Take (GT) 609 juta US$ dan Internal rate of Return (IRR) 15.13%.
Sensitivitas analisis dilakukan dengan variasi harga jual gas dan mengubah
besaran kontraktor split untuk meningkatkan IRR sehingga dapat mencapai nilai
yang masih dapat diterima dari sisi Kontraktor. Untuk mendapatkan IRR yang
lebih besar dari 20%, diperlukan kontraktor split sebesar 48%. Hasil analisa
keekonomian dapat menjadi pertimbangan dalam penentuan besaran kontraktor
split untuk pengembangan lapangan gas laut dalam.

ABSTRACT
Deepwater gas field development has technical challenges, related to production
facilities and technology that can be used for producing oil and gas in the extreme
ambient conditions. The required cost is also higher than shallow water. This
research analyzed technical and economical aspect of deepwater gas field
development at Makasar Strait using subsea tieback method, which utilize the
available capacity from existing Floating Production Unit (FPU). Technical
analysis include selection the optimum flowline size, which meet the gas
deliverability and other criteria as well. It also cover the flow assurance analysis,
particularly hydrate mitigation, to ensure the flow continuity of oil and gas from
subsea well to the sales point. Economic analysis include the calculation of
investment cost on each option that meet the technical criteria above. Then
continued with calculation of economic parameter based on applicable Indonesia
Production Sharing Contract (PSC) scheme. With gas price of 6 US$/mmbtu, will
give Government Take (GT) of 609 million US$ and Internal rate of Return
(IRR) 15.13%. Sensitivity analysis has been done by varrying the gas sale price
and changing the percentage of contractor split to increase the IRR to meet the
value that still acceptable from Contractor side. Contractor split of 48% is
required to achieve IRR higher than 20%. This economic analysis result could
become a consideration in defining the percentage of Contractor Split for
deepwater gas development.;Deepwater gas field development has technical challenges, related to production
facilities and technology that can be used for producing oil and gas in the extreme
ambient conditions. The required cost is also higher than shallow water. This
research analyzed technical and economical aspect of deepwater gas field
development at Makasar Strait using subsea tieback method, which utilize the
available capacity from existing Floating Production Unit (FPU). Technical
analysis include selection the optimum flowline size, which meet the gas
deliverability and other criteria as well. It also cover the flow assurance analysis,
particularly hydrate mitigation, to ensure the flow continuity of oil and gas from
subsea well to the sales point. Economic analysis include the calculation of
investment cost on each option that meet the technical criteria above. Then
continued with calculation of economic parameter based on applicable Indonesia
Production Sharing Contract (PSC) scheme. With gas price of 6 US$/mmbtu, will
give Government Take (GT) of 609 million US$ and Internal rate of Return
(IRR) 15.13%. Sensitivity analysis has been done by varrying the gas sale price
and changing the percentage of contractor split to increase the IRR to meet the
value that still acceptable from Contractor side. Contractor split of 48% is
required to achieve IRR higher than 20%. This economic analysis result could
become a consideration in defining the percentage of Contractor Split for
deepwater gas development., Deepwater gas field development has technical challenges, related to production
facilities and technology that can be used for producing oil and gas in the extreme
ambient conditions. The required cost is also higher than shallow water. This
research analyzed technical and economical aspect of deepwater gas field
development at Makasar Strait using subsea tieback method, which utilize the
available capacity from existing Floating Production Unit (FPU). Technical
analysis include selection the optimum flowline size, which meet the gas
deliverability and other criteria as well. It also cover the flow assurance analysis,
particularly hydrate mitigation, to ensure the flow continuity of oil and gas from
subsea well to the sales point. Economic analysis include the calculation of
investment cost on each option that meet the technical criteria above. Then
continued with calculation of economic parameter based on applicable Indonesia
Production Sharing Contract (PSC) scheme. With gas price of 6 US$/mmbtu, will
give Government Take (GT) of 609 million US$ and Internal rate of Return
(IRR) 15.13%. Sensitivity analysis has been done by varrying the gas sale price
and changing the percentage of contractor split to increase the IRR to meet the
value that still acceptable from Contractor side. Contractor split of 48% is
required to achieve IRR higher than 20%. This economic analysis result could
become a consideration in defining the percentage of Contractor Split for
deepwater gas development.]"
2015
T44510
UI - Tesis Membership  Universitas Indonesia Library
cover
cover
Teddyanus Rozarius, Author
"Unit pompa angguk merupakan salah satu metode pengangkatan buatan dalam teknik produksi minyak bumi yang banyak dipakai oleh perusahaan-perusahaan perminyakan karena teknologinya sederhana dan biaya pengoperasiannya yang relatif murah. Namun demikian, Unit pompa angguk mempunyai banyak bagian-bagian yang bergerak sehingga dapat menyebabkan kegagalan mekanikal. Kegagalan mekanikal ini berupa kerusakan tubing, sucker rod, dan pompa bawah tanah. Disamping itu, masalah reservoar, seperti karena problem kepasiran dan scale, dapat mengakibatkan kegagalan reservoar yang akhirnya membuat sumur berhenti berproduksi. Untuk mengatasi masalah tersebut maka diperlukan perawatan sumur minyak untuk tetap menjaga produksinya. Perencanaan perawatan sumur harus dibuat agar pemeliharaan dapat dilakukan dengan efektif dan efisien.
Dengan menggunakan data historis dari aktivitas perawatan sumur minyak, kita dapat mengenalisa reliabilitasnya dan menyelidiki penyebab kegagalan, tipe kegagalan, dan umur rata-rata sumur tersebut. Dari hasil analisa tadi, kita dapat membuat perencanaan perawatan sumur selanjutnya dengan lebih baik.
Dari hasil evaluasi terhadap data historis aktivitas perawatan sumur di Pertamina Operasi EP Cepu, Jawa tengah, diketahui bahwa sebagian besar sumur minyak tersebut mempunyai tipe kegagalan awal + random, dan hanya sebagian kecil saja yang mempunyai tipe kegagalan usang. Umur rata-rata sumur adalah 85 hari dengan tingkat reliabilitas 31% untuk mencapai umur tersebut. sebagian besar kegagalan disebabkan oleh kegagalan mekanikal. Berdasarkan hasil produksi dan biaya perawatannya, umur relevan sumur minyak di Cepu berkisar antara 68 s/d 160 hari dengan tingkat reliabiltasnya rata-rata 26% untuk mencapai umur tersebut.

Oil Well Work-over Analysis by Using Reliability Function ApproachA Sucker Rod Pumping Unit is one of the artificial lifting method which is widely used in Oil Companies because its technology is simple and relatively cheap. However, a Sucker Rod Pumping Unit has many moving parts that lead to mechanical failure of the unit. Mechanical failure consists of tubing failures, sucker rod failures, and subsurface pump failures. Beside that, reservoir problem, such as sand problem and scale problem, lead to reservoir failure that can stop well production. Considering the problem, the oil well work-over or oil well pulling up is needed to maintain oil well production_ The well work-over planning should be made to conduct oil well maintenance effectively and efficiently
Using historical data of oil well work-over activities, we can analyze the oil well reliability and point out the cause of oil well failure, failure type, failure rate, mean time between failure and etc. From this analysis, we will be able to make a better plan for the oil well work-over.
Evaluating the historical data of oil well work-over activities in Pertamina Cepu Field, Central of Java, we found that most of the oil wells have burn in to random failure type, and only a few of them have wear out failure type. The wells have average mean life 85 days and average reliability 31% to reach its mean life. Most of the oil well failures caused by mechanical problems. Based on their productivity and well work-over operation cost, the expected minimum life of oil wells between 68 days to 160 days; and their reliability is 26% in average to reach those minimum life.
"
Depok: Fakultas Teknik Universitas Indonesia, 1999
Tpdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Sinaga, Andrew Samuelson
"Pengeboran minyak dan gas merupakan suatu kegiatan yang bertujuan untuk membuat lubang ke dalam inti bumi untuk mendapatkan sumber daya minyak dan gas dengan menggunakan rig pengeboran pada suatu sumur. Salah satu karakteristik dari sumur pengeboran adalah sumur dengan kondisi HPHT (High Pressure High Temperature) dimana pada sumur jenis ini suhu dapat mencapai 150°C dan tekanan yang mencapai 15000 psi. Sistem sirkulasi pengeboran merupakan salah satu sistem dari rig pengeboran yang memiliki fungsi untuk mengangkat serpihan formasi dari dasar sumur ke permukaan. mud pump dan solid control merupakan dua aspek dalam sistem sirkulasi pengeboran yang berkaitan langsung satu sama lain. Pengaruh sumur dengan kondisi HPHT (High Pressure High Temperature) sangat signifikan terhadap performa kedua aspek sistem sirkulasi tersebut sehingga memengaruhi proses pengeboran secara keseluruhan.

Oil and gas drilling is an activity intended to make holes into the earth to obtain oil and gas resources using a drilling rig. One of the characteristics of drilling wells is the condition of HPHT (High-Temperature High Pressure) where this type of well can reach 150 ° C and the pressure reaches 15000 psi. The drilling circulation system is one of the systems of the drilling rig that has the function to lift the formation of debris from the bottom of the well to the surface. Mud pump and solid control are two aspects in the drilling circulation system that are directly related to each other. The influence of HPHT (High-Pressure High Temperature) conditions on well is very significant for the performance of both aspects of the circulation system thus affecting the overall drilling process.
"
Depok: Fakultas Teknik Universitas Indonesia, 2019
SP-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
M. Faizal Yamin
"Semakin meningkatnya aktifitas industri pengeboran minyak dan gas sekarang ini maka dibutuhkan suatu manajemen untuk mengurangi risiko kegagalan yang mungkin texjadi dalam sistem pengeboran. Manajemen yang baik dalam pengontrolan risiko kegagalau dapat meningkatkan daya saing terhadap kompetitor dan menjaga kepercayaan dari klien. PT. D&M Schlumberger merupakan perusahaan yang bergerak di bidang jasa pengeboran dimana perusahaan ini menyewakan alat-alat pengeboan minyak. Kegagalan dalam siatem pengeboran bisa disebabkan oleh alat, sumber daya manusia dan lingkungan. Oleh karena itu diperlukan aualisa risiko kegagalan untuk mengidentifikasi, mengontrol dan meminimalkan dampak dari kegagalan dalam sistem pengeboran. Dengan menganalisa risiko kegagalan pada PT. D&M Schlumberger yang terjadi maka akan didapat probabilitas risiko kegagalan yang terbesar dan alat pcngeboran yang sering mengalami kegagalan dalam sistern pengeboran."
Depok: Fakultas Teknik Universitas Indonesia, 2006
S50423
UI - Skripsi Membership  Universitas Indonesia Library
cover
Miftahul Bayan
"ABSTRAK
Terjebaknya pipa (stuck pipe) selama pengeboran sumur Geotermal adalah salah satu masalah yang mempengaruhi waktu tidak produktif (NPT) yang memperpanjang jadwal pengeboran. Masalah ini secara langsung meningkatkan biaya pengeboran karena meningkatnya waktu pengeboran keseluruhan, bahan habis pakai, lumpur, mata bor dan juga akan mengorbankan sumur ketika tidak ada lagi kemajuan untuk mencapai kedalaman cadangan (reservoir) yang ditargetkan. Juga masalah suckpipe akan menciptakan efek domino yang mungkin berdampak pada pengeboran sumur berikutnya dan jadwal pengeboran lokasi lainnya. Masalah stuck pipe terjadi dari banyak faktor kontributor dan juga terkait dengan kasus masalah lain seperti kehilangan sirkulasi,
ketidakstabilan lubang sumur, penutupan zona sementara, dan masalah pekerjaan penyemenan. Metode analitik yang ada saat ini sebagian besar menggunakan satu atau dua variabel dominan untuk memprediksi masalah pipa macet yang secara terbatas mewakili kondisi pengeboran, litologi dan kondisi sumur bor. Kombinasi metode statistik dan pendekatan pembelajaran mesin (machine learning) dikembangkan dan digunakan secara komprehensif untuk memprediksi masalah stuck pipe yang mewakili berbagai kondisi litologi, lubang sumur dan pengeboran. Data historis yang mewakili situasi kondisional dan perekam pengeboran elektronik (Electronic Drilling Recorder) digunakan untuk memprediksi masalah stuck pipe yang berbeda untuk setiap sumur. Banyak faktor yang berkontribusi terhadap keberhasilan kegiatan pengeboran dan tidak ada faktor tunggal, yang dominan menjadi akar penyebab menariknya penelitian ini. Pendekatan statistik seperti Principal Component Analysis, regresi logistik, dan analisis
diskriminan sangat membantu untuk menafsirkan data sebelum langkah analisis selanjutnya. Analisis statistik tersebut harus menjadi dasar interpretasi data sebelum membuat algoritma untuk menggunakan analisis prediktif menggunakan pembelajaran mesin (machine learning) dan pembelajaran mendalam (deep learning).

ABSTRACT
Stuck pipe during Geothermal well drilling is one of the problems that affect nonproductive time (NPT) which prolongs the drilling schedule. This problem directly increases drilling cost due to increasing overall drilling time, consumables, mud, drill bit and as well as sacrifices it's well when there is no more progress to reach the targeted reservoir depth. Also, the stuck pipe problem will create a domino effect that might impact next well drilling and another site drilling schedule. Stuck pipe problem is made from many contributor factors and related to other problem cases such as lost circulation, wellbore instability, temporary zone closure, and cementing job trouble. The current analytical method mostly uses one or two dominant variables to predict stuck pipe problems which limitedly represents drilling conditions, lithology and wellbore conditions. A combination of statistical method and machine learning approach is developed and comprehensively used to predict stuck pipe problem that represents different well lithology, wellbore and drilling condition. Historical data that represents the conditional situation and electronic data recorder is used to predict the stuck pipe problem which different for each of the well. Many factors contribute to successful drilling activities and no one single factor, which dominantly becomes the root cause of the problem. A statistical approach such as principal component analysis, logistic regression and discriminant analysis is very helpful to interpret data before the next step of the analysis. Those statistical analyses should be the baseline of data interpretation before creating an algorithm to use predictive analysis using machine learning and deep learning."
Depok: Fakultas Teknik Universitas Indonesia, 2020
T-Pdf
UI - Tesis Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>