Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 129382 dokumen yang sesuai dengan query
cover
Muhamad Yasil Farabi
"Pada skripsi ini, dirancang sebuah simulator sel surya menggunakan buck converter yang kemudian dianalisis menggunakan diagram bode dan TKA. Model statik sel surya digunakan untuk mengimplementasikan karakteristik dari sel surya. Low-pass filter digunakan untuk mengubah model statik sel surya menjadi model dinamik sel surya. Pengendali PI digunakan untuk mengendalikan switch buck converter melalui pulsa-pulsa yang dihasilkan oleh PWM Generator. Sistem dianalisis menggunakan diagram bode terhadap masukannya, yaitu solar irradiance dan suhu sel. Beban, konstanta proportional, dan konstanta integral akan divariasikan untuk menganalisis sistem. Sistem juga dianalisis dengan menggunakan TKA untuk mengetahui seberapa besar batas gain kestabilan sistem. Dari diagram bode yang didapat, sistem terlihat menyerupai sistem orde tiga. Dari TKA, dengan mengubah beban didapat bahwa batas gain kestabilan sistem sangatlah tinggi, sekitar untuk masukan perubahan solar irradiance, dan untuk masukan perubahan suhu sel. Karena nilai tersebut sangatlah tinggi, sehingga sistem dapat dinyatakan robust terhadap perubahan beban dan cenderung stabil.

This thesis presents a Photovoltaic Simulator Simulation using Buck Converter with analysis using bode diagram and root locus. A PV Static Model is used to implement the characteristics of actual solar cell. A Low-Pass Filter is used to turn the static model of photovoltaic into the dynamic model. PI Controller is used to control buck converter?s switch via PWM Generator. The system is analyzed using bode diagram for its inputs, such as solar irradiance and cell?s temperature. Load, Kp, and Ki will be varied to analyzed the system. Root locus method is used to analyze the maximum gain system. From bode plot, the analyzed system similar to third order system. From root locus, the limits of gain stability system are so high about for solar irradiance input, and for cell?s temperature input, so the system can be declared stable."
Depok: Fakultas Teknik Universitas Indonesia, 2011
S89
UI - Skripsi Open  Universitas Indonesia Library
cover
Rekioua, Djamila
"Photovoltaic generation is one of the cleanest forms of energy conversion available. One of the advantages offered by solar energy is its potential to provide sustainable electricity in areas not served by the conventional power grid.
Optimisation of photovoltaic power systems details explicit modelling, control and optimisation of the most popular stand-alone applications such as pumping, power supply, and desalination. Each section is concluded by an example using the MATLAB® and Simulink® packages to help the reader understand and evaluate the performance of different photovoltaic systems."
London: Springer, 2012
e20397694
eBooks  Universitas Indonesia Library
cover
Suhada Bagus Solihin
"Dengan adanya perangkat lunak simulasi, maka dapat membuat suatu model sistem sel surya atau disebut dengan photovolotaic simulator agar dapat mempelajari kinerja pengisian baterai, tanpa harus selalu memasangkan baterai dengan sel surya. Saat ini sudah banyak PV simulator dengan berbagai varisi metode dan perumusan. Perangkat lunak semacam ini sangat membantu sekali khususnya pada industri-industri automasi maupun laboratorium karena sifatnya yang mempermudah dalam melakukan perancangan maupun analisa suatu masalah. Penelitian mengenai photovoltaic simulator dengan menggunakan dua komponen perangkat lunak (software). Komponen software pertama menggunakan National Instruments (NI) LABVIEW untuk membuat Model Sel Surya, sementara komponen software kedua menggunakan NI Multisim untuk membuat model Semi Konverter Satu Fasa. Pertama-tama, model matematis dari photovoltaic (sel surya) akan dijelaskan terlebih dahulu. Kemudian, setelah didapat model matematis dari sel surya, Photovoltaic Simulator akan direalisasikan ke dalam LABVIEW selanjutnya membuat rangkaian Semi Konverter Satu Fasa menggunakan Multisim. Photovoltaic Simulator akan mengendalikan konverter menggunakan pengendali IP dengan referensi terhadap model photovoltaic. Sinyal kendali dari pengendali IP dipakai untuk menghasilkan sinyal PWM yang mengatur sudut penyalaan konverter. Masukan berupa irradiansi dan suhu diberikan ke Photovoltaic Simulator, kemudian arus dan tegangan dari konverter akan di umpan balik ke Photovoltaic Simulator. Kesimpulan dari penelitian ini adalah arus dan tegangan konverter mengalami kenaikan saat irradiansi dan suhu meningkat.

With the simulation software, it is possible to create a model of a solar cell system or called a photovolotaic simulator in order to study battery charging performance, without having to always install a battery with solar cells. Currently, there are many PV simulators with various methods and formulations. This kind of software is very helpful, especially in automated and laboratory industries because of its nature which makes it easier to design and analyze a problem. Research on photovoltaic simulators using two software components. First, software components use National Instruments (NI) LABVIEW to create the Solar Cell Model, while the second software is NI Multisim to create semi converter single phase circuit model. First, the mathematical model of the solar cell will be explained. Then, this mathematical model realized using LABVIEW. Second, creating semi converter single phase circuit model using Multisim. The Photovoltaic Simulator will control the converter using IP controller in the reference of the photovoltaic model. Control signals from IP controller are used to generate PWM signal, which control the triggering angle of the converter. Irradiance and temperature inputs are given to the Photovoltaic Simulator, then the current and voltage outputs from converter will be used as feedbacks to the Photovoltaic Simulator. The result from this research the Voltage and current increase when the Irradiance and temperature inputs increase."
Depok: Fakultas Teknik Universitas Indonesia, 2013
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Nadia Rachma Yunia
"Listrik adalah salah satu kebutuhan yang sangat mendasar pada zaman ini, perannya sangat besar mulai dari listrik untuk rumah penduduk hingga memenuhi kebutuhan skala besar seperti usaha pabrik dan mendukung instansi pemerintahan. Penggunaan bahan bakar yang paling besar untuk pembangkit listrik di Indonesia saat ini masih menggunakan batu bara, sementara batu bara bukan termasuk energi terbarukan sehingga dapat habis di kemudian hari. Photovoltaic sistem adalah sebuah sistem yang menggunakan energi dari cahaya matahari untuk diubah menjadi energi listrik. Photovoltaic sistem ini menggunakan solar sel yang kemudian dapat dibuat dalam skala lebih besar menjadi solar modul atau solar array. Photovoltaic dapat digunakan secara on-grid ataupun off-grid. Kemudian, agar sistem photovoltaic dapat digunakan sebagai pembangkit, sistem ini dapat dihubungkan dengan kontroler Maximum Power Point Tracker (MPPT) dan converter. Dalam skripsi ini jenis MPPT yang digunakan adalah Perturb and Observation (P&O) dan converter yang digunakan adalah dc-dc converter buck-boost. MPPT P&O digunakan karena algoritmanya yang sederhana sehingga banyak digunakan dan buck-boost converter digunakan agar tegangan output yang dihasilkan dapat disesuaikan dengan beban yang divariasikan.

Electricity is one of the very basic needs of this era, its role is very large ranging from electricity to houses to meet large-scale needs such as factory businesses and supporting government agencies. The use of the largest fuel for electricity generation in Indonesia is currently still using coal, while coal is not included as renewable energy so it can be used up later. Photovoltaic systems are system that uses energy from sunlight to be converted into electrical energy. This photovoltaic system uses solar cells which can then be made on a larger scale into solar modules or solar arrays. Photovoltaic can be used as on-grid or off-grid. Then, so that the photovoltaic system can be used as a generator, this system can be connected to the Maximum Power Point Tracker (MPPT) controller and converter. In this thesis the type of MPPT used is Perturb and Observation (P & O) and the converter used is a dc-dc buck-boost converter. MPPT P & O is used because the its simple algorithm and widely used in othe Solar Power Generation System and the buck-boost converter is used so that the output voltage can be adjusted to the varied load."
Depok: Fakultas Teknik Universitas Indonesia, 2019
S-Pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Samuel Guswindo
"Laporan skripsi ini membahas tentang Photovoltaic Simulator yang dijalankan secara real time. Penelitian ini terbagi atas komponen software dan hardware. Komponen software meliputi Model Sel Surya yang dijalankan dengan MATLAB SimulinkTM menggunakan CMEX, sementara komponen hardware meliputi DC-DC converter, yaitu buck converter. Pertama-tama, model matematis dari photovoltaic atau sel surya akan dijelaskan terlebih dahulu. Kemudian, setelah didapat model matematis dari sel surya, Photovoltaic Simulator akan direalisasikan ke dalam MATLAB. Photovoltaic Simulator akan mengendalikan arus buck converter menggunakan pengendali IP dengan referensi terhadap model photovoltaic. Sinyal kendali dari pengendali IP akan dipakai untuk menghasilkan sinyal PWM, yang kemudian dikirimkan ke buck converter. Masukan berupa iradiansi dan suhu diberikan ke Photovoltaic Simulator, kemudian arus dan tegangan dari buck converter akan di-feedback-kan ke Photovoltaic Simulator.

This report will explain about Photovoltaic Simulator that is run in real time. This study consists of software and hardware components. Software components are Solar Cell Model that is run in MATLAB SimulinkTM using CMEX, while the hardware component is a DC-DC converter, which is a buck converter. First, the mathematical model of the solar cell will be explained. Then, the mathematical model of the solar cell is realized into MATLAB. The Photovoltaic Simulator will control the current of the buck converter using IP controller in the reference of the photovoltaic model. Control signals from IP controller are used to generate PWM signal, which then are sent to the buck converter. Irradiance and temperature inputs are given to the Photovoltaic Simulator, then the current and voltage outputs from buck converter will be used as feedbacks to the Photovoltaic Simulator."
Depok: Fakultas Teknik Universitas Indonesia, 2012
S42467
UI - Skripsi Open  Universitas Indonesia Library
cover
Difi Nuary Nugroho
"ABSTRAK
Industri Semen merupakan industri yang padat akan penggunaan energi listrik. Selain itu
emisi buangan berupa debu sebagai hasil sampingan proses yang tidak sempurna ketika
melakukan proses produksi yang akan memberikan dampak ke lingkungan sekitar di areal
pabrik. Kondisi ini menjadi pertimbangan ketika ingin menerapkan energi terbarukan khusunya
photovoltaic di areal industri khusunya industri semen.Pemanfaatan energi matahari di Industri
semen tidak dapat digunakan sebagai suplai daya utama melainkan sebagai suplai daya cadangan
untuk sistem kontrol dengan total beban sebesar 4 KW berbasis smart system dengan dua suplai
daya yaitu dari daya eksisting serta daya photovoltaic.Namun dari pengaruh emisi yang
dihasilkan akan berdampak pula kepada meningkatnya biaya operasional dan pemeliharaan yang
semula 0,8% hingga 1,5% (IEA 2008) menjadi 3,65% dari biaya investasi awal. Dalam analisa
keekonomian terdapat dua skenario dalam perhitungannya meliputi pengurangan biaya listrik
ataupun sebagai sumber pendapatan baru yang masing masing memiliki kelebihan dan
kekurangan. Selain itu dalam pemanfaatan energi matahari pada industri semen dapat
menjadikan perusahaan tersebut menjadi green company dengan mendapatkann reward dari hasil
carbon credit dari CO yang dikurangkan

ABSTRACT
Cement industry is intensive industries will use electrical energy. In addition exhaust
emissions of dust as a unsufficient of the process is not perfect when the production process that
will give impact to the surrounding environment in the factory area. This condition into
consideration when you want to implement renewable energy especially solar photovoltaic
industry especially in the area of the cement industry. It affects the rising cost of operating and
maintaining the original 0.8% to 1.5% (IEA 2008) to 3.65% of the initial investment cost. Solar
energy utilization in the cement industry can not be used as the main power supply but rather as
a backup power supply for the control system with a total load of 4 KW-based smart system with
two power supplies that of existing power and photovoltaic power. In the economic analysis,
there are two scenarios in its calculations include a reduction in the cost of electricity or as a
new source of revenue that each has advantages and disadvantages. In addition to the utilization
of solar energy in the cement industry can make the company become a green company with
getting reward from the carbon credit that is subtracted from the CO.;"
2015
T43778
UI - Tesis Membership  Universitas Indonesia Library
cover
Reikan Kresna Maulana
"Penggunaan metode direct untuk MPPT seperti increamental conductance, perturb and orbservation tidak menghasilkan pencarian yang cepat dan berosilasi pada daerah MPP. Perubahan nilai duty yang tetap dari metode tersebutlah yang menghasilkan keadaan tersebut. Sedangkan penggunaan metode PID dapat menghasilkan pencarian lebih cepat dan menghasilkan osilasi lebih kecil tetapi metode ini dikategorikan metode inderect dikarenakan pencarian titik tegangan referensi berdasanakan metode trial and error. Sehingga diajukan penggunaaan metode direct yang lain dengan yang menghasilkan pencarian lebih cepat dan osilasi lebih kecil yaitu penggunaan logika fuzzy. Perancangan dilakukan dengan metode simulasi, yaitu mensimulasikan rangkaian yang akan dipergunakan, rangkaian buck converter, dan beban yang berupa baterai dan mendapatkan nilai masukan jika nilai PWM rangkaian buck converter diubah – ubah. Untuk membandingkan hasil penggunaan algoritma fuzzy, akan disajikan perbandingan jika menggunakan algoritma P&O, hasil didapatkan nilai tanggapan waktu menggunakan algoritma fuzzy lebih cepat dan tunak setelah 347,8246 mikro sekon dibandingkan 608,6962 mikro sekon jika menggunakan algoritma P&O, didapatkan hasil arus tunak pada besar arus 1.6525 Ampere pada sisi keluaran sedangkan dengan menggunakan algoritma P&O akan berosilasi diantara 1.281 Ampere dan 1.689 Ampere, menunjukan bahwa penggunaan algoritma fuzzy manghasilkan hasil yang lebih baik untuk sistem pengecasan baterai dikarenakan terdapat mode constant current pada saat pengisian baterai lithium – ion yang perlu diperhatikan.

The use of direct methods for MPPT such as increamental conductance, perturb and orbservation does not result in fast and stable power tracking in the MPP region. It is the fixed changes in duty value of the mentioned method that is resulting such situation. Whereas the use of the PID method can produce a much faster power tracking with smaller oscillations, but as this method is categorized as an inderect method the search for the correct voltage refenrece points is still based on the trial and error method.So, it is proposed to use another direct method which could result in much faster power tracking with smaller oscillations, namely the use of fuzzy logic algorithm. The design is carried out by simulation method, namely simulating the circuit to be used, the buck converter circuit, and the load in the form of a battery and obtaining the input and ouput value in reference to PWM value of the buck converter circuit, when the value is varied. To compare the results of using the fuzzy algorithm, a comparison will be presented such when using the P&O algorithm. The end results obtained is that the rise time of using the fuzzy algorithm are much faster and able to reach stedy state condition after just 347.8246 micro seconds compared to 608.6962 micro seconds when using the P&O algorithm, another result is that the current value are stable at 1.6525 Ampere at the battery output side, while using the P&O algorithm it will oscillate between 1.281 Ampere and 1.689 Ampere, indicating that the use of the fuzzy algorithm produces better results for a system with battery load because there is a constant current mode when recharging lithium-ion batteries that need to be noted."
Depok: Fakultas Teknik Universitas Indonesia, 2020
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Fahmy Miftahurrahman
"Konsumsi listrik pada sektor perumahan di Indonesia cukup tinggi. Salah satu cara yang mungkin untuk mengurangi konsumsinya dengan menerapkan konsep near Zero Energy Building. Strategi retrofit adalah salah satu strategi untuk menggabungkan efisiensi energi dan efektivitas biaya. Pemilihan modul surya berdampak langsung pada daya yang dihasilkan sehingga perlu dioptimalkan. Di sisi lain, pemilihan peralatan listrik juga perlu dioptimalkan untuk efisiensi konsumsi energi. Dalam penelitian ini, meminimalkan biaya retrofit dan menemukan kombinasi biaya optimal, teknologi efisiensi energi dan sistem pembangkit energi terbarukan digabungkan dan diteliti. Pemilihan peralatan untuk memasak, pendinginan ruang, dan jenis peralatan umum diadakan berdasarkan biaya energi per beban dan harga peralatan. Hasil pemodelan matematika dan simulasi adalah kombinasi peralatan penanak nasi Cosmos CRJ-9303, water dispenser Polytron PWC-777, lemari es Panasonic NR-BN209N, pengkondisi udara Gree C3E, televisi SONY KD-43X7500F, pompa air Shimizu PC-260BIT, dan mesin cuci Sharp ES-FL872. Kombinasi ini membutuhkan 5,678 kWh energi pertahun. Modul surya jenis mono-crystalline standar kapasitas 4.5 kWp menghasilkan energi sebesar 5,891 kWh pertahun, memerlukan ruang sebanyak 26.1 m2 pada atap model. Perbandingan energi peralatan listrik dengan modul surya menghasilkan AEMR sebesar 104%, sehingga dapat dinyatakan bahwa model dengan kombinasi tersebut memenuhi persyaratan dalam penerapan konsep nZEB dengan biaya retrofit optimum sebesar Rp 106,076,459.

The power consumption for the residential in Indonesia is quite high. It makes sense to reduce consumption by applying the near Zero Energy Building concept. The retrofit strategy is one strategy for combining energy efficiency and cost-effectiveness. PV system equipment impact directly to generated power, need to be optimized. On the other side, load equipment needs to be optimized for energy consumption efficiency. In this research, minimizing the retrofit cost and find a cost-optimal package, energy efficiency technologies and Renewable energy generation systems be combined and investigated. Equipment selection for cooking, space cooling, and general appliances type held based on cost per load energy and equipment price. The result of mathematical modelling and simulation is combination of appliances; Cosmos CRJ-9303 rice cooker, Polytron PWC-777 water dispenser, Panasonic NR-BN209N refrigerator, Gree C3E air conditioner, SONY KD-43X7500F television, Shimizu PC-260BIT water pump, and Sharp ES-FL872 washing machine. This combination requires 5,678 kWh annual energy. Standard mono-crystalline PV module with 4.5 kWp capacity could generate 5,891 kWh annually, required 26.1 m2 roof space. Comparison between energy consumption and supply is 104%, it can be stated that the model meets the requirements in applying the nZEB concept, with optimum retrofit cost of Rp 106,076,459."
Depok: Fakultas Teknik Universitas Indonesia, 2020
T55330
UI - Tesis Membership  Universitas Indonesia Library
cover
Farisz Firstian Arya
"Pemanfaatan sistem photovoltaic (PV) sangat penting dalam mencapai Sustainable Development Goal (SDG) nomor 7, yang bertujuan menyediakan energi bersih dan terjangkau untuk semua. Namun, salah satu kendala utama yang dihadapi dalam implementasi PV adalah efisiensi yang masih belum optimal, terutama dalam kondisi lingkungan yang berubah-ubah. Dalam penelitian ini, digunakan algoritma MPPT Incremental Conductance yang dikombinasikan dengan implementasi two-phase interleaved boost converter untuk meningkatkan efisiensi sistem PV dan mengurangi nilai ripple. Seluruh pengujian dilakukan melalui simulasi pada perangkat lunak Simulink MATLAB, serta menggunakan data aktual iradiasi dan suhu dari beberapa hari di bulan Agustus 2023. Hasil simulasi menunjukkan bahwa algoritma MPPT Incremental Conductance terbukti efektif dalam menemukan titik kerja optimal sistem PV pada kondisi Standard Test Conditions (STC). Implementasi two-phase interleaved boost converter pada sistem PV meningkatkan efisiensi daya keluaran secara signifikan, dengan penurunan persentase error dari 9.05% menjadi 5.85%, serta mengurangi ripple dari 2.31% menjadi 1.22%. Meskipun perubahan pada parameter dinamik tidak signifikan, dengan tracking speed yang hanya berubah sedikit dari 0.55 detik menjadi 0.53 detik, sistem MPPT ini mampu merespon perubahan kondisi lingkungan secara efektif, menjaga titik kerja optimal. Hasil penelitian ini menunjukkan bahwa kombinasi MPPT Incremental Conductance dan two-phase interleaved boost converter efektif meningkatkan performa sistem pada kondisi iradiasi lebih dari 684 W/m2 hingga 1000 W/m2.

The utilization of photovoltaic (PV) systems is crucial in achieving Sustainable Development Goal (SDG) number 7, which aims to provide clean and affordable energy for all. However, one of the main challenges in the implementation of PV systems is the suboptimal efficiency, particularly under varying environmental conditions. In this study, the Incremental Conductance MPPT algorithm was used in combination with the implementation of a two-phase interleaved boost converter to improve the efficiency of the PV system and reduce ripple values. All testing was conducted through simulations in Simulink MATLAB software, using actual irradiation and temperature data from several days in August 2023. The simulation results showed that the Incremental Conductance MPPT algorithm effectively found the optimal operating point of the PV system under Standard Test Conditions (STC). The implementation of the two-phase interleaved boost converter in the PV system significantly increased the output power efficiency, with a reduction in error percentage from 9.05% to 5.85%, and reduced ripple from 2.31% to 1.22%. Although the changes in dynamic parameters were not significant, with tracking speed only slightly changing from 0.55 seconds to 0.53 seconds, this MPPT system was able to respond effectively to environmental condition changes, maintaining the optimal operating point. The results of this study indicate that the combination of the Incremental Conductance MPPT and two-phase interleaved boost converter is effective in improving system performance under irradiation conditions from 684 W/m2 to 1000 W/m2."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Achmad Fauzan Azima
"Pemanfaatan energi surya sebagai sumber energi listrik terbarukan di Indonesia perlu dipercepat untuk mencapai target bauran energi terbarukan sebesar 23% pada tahun 2025 dan Net Zero Emission (NZE) pada tahun 2060. Salah satu cara untuk meningkatkan efisiensi penggunaan energi surya adalah melalui sistem fotovoltaik dengan teknik Maximum Power Point Tracking (MPPT) bersama dengan penggunaan boost converter. Algoritma Perturb and Observe (P&O) memiliki kelemahan berupa osilasi steady-state yang tinggi pada Large Step P&O (LSPO) dan tracking speed yang lambat pada Small Step P&O (SSPO). Penelitian ini mengembangkan algoritma Modified P&O (MPO) yang memanfaatkan metode estimasi open-circuit voltage untuk mengatasi kelemahan pada algoritma P&O. Algoritma MPO membagi kurva operasi PV menjadi empat bagian untuk mengkombinasikan tracking speed dari LSPO dan kestabilan dari SSPO. Simulasi dilakukan menggunakan perangkat lunak Simulink MATLAB dengan data iradiasi dan suhu dari Kota Depok. Hasil penelitian menunjukkan bahwa algoritma LSPO dan MPO cocok digunakan pada iradiasi rendah, algoritma MPO cocok digunakan pada iradiasi menengah, dan algoritma SSPO cocok digunakan pada iradiasi tinggi. Perlu penggunaan baterai untuk menyimpan daya yang melebihi spesifikasi boost converter agar algoritma MPO bekerja dengan optimal pada kondisi iradiasi tertinggi. Secara keseluruhan, algoritma MPO lebih baik daripada algoritma SSPO dan LSPO karena menghasilkan nilai mean yang tinggi seperti LSPO dan memiliki osilasi steady-state yang kecil seperti SSPO.

The utilization of solar energy as a renewable electricity source in Indonesia needs to be accelerated to achieve the renewable energy mix target of 23% by 2025 and Net Zero Emission (NZE) by 2060. One way to increase the efficiency of solar energy use is through photovoltaic systems with Maximum Power Point Tracking (MPPT) techniques along with the use of a boost converter. The Perturb and Observe (P&O) algorithm has drawbacks such as high steady-state oscillations in Large Step P&O (LSPO) and slow tracking speed in Small Step P&O (SSPO). This study develops a Modified P&O (MPO) algorithm that utilizes the open-circuit voltage estimation method to address the weaknesses in the P&O algorithm. The MPO algorithm divides the PV operation curve into four parts to combine the tracking speed of LSPO and the stability of SSPO. The simulation was conducted using Simulink MATLAB software with irradiation and temperature data from Depok City. The study results show that LSPO and MPO algorithms are suitable for low irradiation, the MPO algorithm is suitable for medium irradiation, and the SSPO algorithm is suitable for high irradiation. A battery is needed to store the power that exceeds the boost converter specifications to optimize the MPO algorithm's performance under the highest irradiation conditions. Overall, the MPO algorithm is superior to the SSPO and LSPO algorithms because it produces a high mean value like LSPO and has low steady-state oscillations like SSPO."
Depok: Fakultas Teknik Universitas Indonesia, 2024
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>