Hasil Pencarian  ::  Simpan CSV :: Kembali

Hasil Pencarian

Ditemukan 215605 dokumen yang sesuai dengan query
cover
Annisa Destavia Bastarina
"Tujuan dari penelitian ini adalah untuk mempelajari laju korosi pada daerah-daerah las dari material baja ASTM A 106 grade B yang digunakan pada industri geothermal. Tiga daerah tersebut adalah daerah logam dasar, daerah HAZ, dan daerah logam las yang diletakkan pada empat jenis larutan elektrolit, yaitu kondensat CT 01, CT 02, CT 03, dan Down Stream dengan menggunakan tiga elektroda sel elektrokimia untuk menghitung laju korosi. Dalam penelitian ini, perhitungan Index Langelier dan Ryznar menunjukkan bahwa kondensat CT 03 merupakan larutan kondensat yang bersifat paling korosif dari keempat larutan elektrolit yang digunakan. Kurva tafel dan parameter korosi dari tiga jenis sampel memperlihatkan bahwa sampel daerah HAZ memiliki laju korosi tertinggi daripada daerah logam dasar dan daerah logam las.
Laju korosi tertinggi pada penelitian ini adalah 7 mpy dimana didapatkan pada daerah HAZ di larutan kondensat CT 03. Laju korosi yang relatif tinggi pada daerah HAZ disebabkan karena kehadiran struktur bainit bawah yang terbentuk di daerah ini selama proses pengelasan dan pembekuan. Adanya pertumbuhan butir, ferrite, pearlite dan bainit bawah di daerah HAZ ditunjukkan dari foto mikro yang diambil pada daerah ini. Struktur widmanstatten ditemukan pada daerah logam las yang memberikan hasil nilai kekerasan sebesar 151 BHN, dimana merupakan nilai kekerasan tertinggi yang didapatkan pada penelitian ini. Nilai kekerasan pada daerah lain antara lain , daerah HAZ 137 BHN dan daerah logam dasar 132 BHN. Foto mikro daerah logam dasar memperlihatkan bahwa daerah ini terdiri dari ferrite dan pearlite dimana, merupakan struktur yang biasa terbentuk pada baja karbon seperti baja ASTM A 106 grade B yang digunakan pada penelitian ini.

The purpose of this research was to study the corrosion rate of welded ASTM A 106 grade B steel used at the geothermal industry. Three zones of this welded steel ? i.e. base metal, HAZ, and base metal were studied in four kinds of electrolytes ? i.e. condensate CT01, CT02, CT03, and Down Stream by means of a three-electrode electrochemical cell in order to measure their corrosion rates. Based on the calculation of Langelier and Ryznar Index, condensate CT03 was the most corrosive electrolyte of four ones used in this research. Tafel curves and corrosion parameters of three kinds of tested samples showed that the sample of HAZ exhibited a higher corrosion rate than the ones of the base metal and weld zone.
The highest corrosion rate in this research was 7 mpy which was obtained at HAZ in the condensate CT03. The relatively high corrosion rate of the HAZ zone might be attributable to the presence of lower bainite structure formed in this zone during welding and solidification. The presence of grain growth, ferrite, pearlite and lower bainite in the HAZ was evidenced by the micrograph taken on this zone. Widmanstatten structures found in the weld zone successfully yielded the hardness of 151 BHN, which was the highest hardness value obtained in this research. The hardness values of other zones ? i.e. HAZ and base metal zone were 137 and 132 BHN, respectively. The micrograph of base metal showed that this zone consisted of ferrite and pearlite which were the natural structures formed in the carbon steel like ASTM A 106 grade B steel used in this research.
"
Depok: Fakultas Teknik Universitas Indonesia, 2008
S51075
UI - Skripsi Open  Universitas Indonesia Library
cover
cover
Sianipar, H. Fernando
"Dalam lingkungan bisnis modern, perusahaan yang sukses tidak dapat mentolerir kegagalan korosi, terutama yang melibatkan cedera pribadi, kematian, tidak terjadwal penutupan dan pencemaran lingkungan. Baja karbon merupakan material yang sangat banyak digunakan pada industri pertambangan, perminyakan dan petrokimia. Penggunaan baja karbon tersebut membutuhkan proteksi dari proses korosi. Penelitian ini dimaksudkan untuk pemanfaatan magnesium serbuk dengan proses penyerutan anoda korban yang sudah tidak terpakai untuk digunakan sebagai material campuran pada cat epoksi resin. Material dasar (substrat) yang digunakan adalah baja karbon rendah AISI SS400. Metode pengujian antara lain uji tarik, komposisi kimia, sembur garam (salt spray) ketebalan (DFT), EIS dan Polarisasi, SEM dan EDX. Ukuran serbuk kurang dari 177 µm. hasil pengamatan visual bahwa cat tampak lebih gelap tergantung dari jumlah serbuk yang ditambahkan, dikarenakan adanya penambahan viskositas dari cat epoksi. Nilai tarik cat dengan nilai paling besar yaitu sistem pengecatan 0g dengan nilai sebesar 7.8Mpa dan untuk ikatan adhesive-nya untuk semua bagus untuk semua jenis pengecatan, karena kegagalan cat masuk kategori kegagalan kohesif bukan pada substrat baja. Uji gores dan sembur garam dapat disimpulkan bahwa semua sistem pengecatan tidak terjadi pelebaran goresan. Pada pengamatan SEM dan EDX bahwa material serbuk magnesium hanya sedikit pada produk karat.Uji EIS menunjukkan bahwa sistem pengecatan 30g memiliki tahanan (Rct) yang paling tinggi dan hasil uji polarisasi sistem pengecatan 30g memiliki laju korosi paling kecil.

In the modern business environment, successful companies cannot tolerate corrosion failures, especially those involving personal injury, death, unscheduled shutdowns and environmental pollution. Carbon steel is a material that is widely used in the mining, petroleum and petrochemical industries. The use of carbon steel requires protection from the corrosion process. This research is intended to utilize magnesium powder by shaving the sacrificial anoda which is not used to be used as a mixed material in epoxy resin paint. The base material (substrate) used is AISI SS400 low carbon steel. Test methods include tensile test, chemical composition, thickness salt spray (DFT), EIS and Polarization, SEM and EDX. Powder size is less than 177 m. visual observation that the paint looks darker depending on the amount of powder added, due to the addition of the viscosity of the epoxy paint. The paint tensile value with the highest value is the 0g painting system with a value of 7.8Mpa and the adhesive bond for all is good for all types of painting, because paint failure is categorized as a cohesive failure not on a steel substrate. The scratch test and salt spray can be concluded that all painting systems do not occur scratch widening. On SEM and EDX observations, there was only a small amount of magnesium powder in the rust product. The EIS test showed that the 30g painting system had the highest resistance (Rct) and the 30g paint system polarization test results showed the lowest corrosion rate."
Depok: Fakultas Teknik Universitas Indonesia, 2021
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Dzil Mulki Heditama
"Penentuan zona rekahan reservoar di daerah Geotermal sangat penting untuk keperluan penentuan titik pemboran. Penentuan zona rekahan tersebut dapat dilakukan dengan menerapkan metode geofisika, salah satunya adalah metode microearthquake (MEQ). Metode MEQ dapat memberikan informasi yang berkaitan dengan struktur permeabilitas reservoar, pola pergerakan fluida injeksi, dan batas reservoar pada lapangan Geotermal. Terdapat beberapa metode penting yang dilakukan untuk analisis zona rekahan dari data MEQ, yaitu relokasi menggunakan metode double difference, tensor momen dan tomografi. Dalam hal ini penulis berupaya untuk melakukan penelitian pengembangan software terkait penentuan waktu tiba menggunakan spektrogram. Setelah lokasi hiposenter diperoleh, maka langkah berikutnya adalah melakukan analisis tensor momen dan tomografi. Dari berbagai analisis yang dilakukan tersebut, penentuan zona rekahan di daerah Geotermal dapat dilakukan dengan baik. Diharapkan penelitian ini memberikan hasil yang terbaik sehingga metode yang dilakukan tersebut dapat diterapkan dalam penentuan zona rekahan yang lebih tepat.

Determination of the reservoir fracture zone in Geothermal areas are very important for the purposes of determining the drilling point. Determination of the fracture zone can be performed by applying geophysical methods, one of which is a microearthquake (MEQ) method. MEQ method may provide information relating to the structure of the reservoir permeability, patterns of fluid injection movement, and boundary the field of Geothermal reservoir. There are several important methods to analyze fracture zone performed on the data MEQ, relocation using the double difference method, moment tensor and tomography. In this case the author seeks to conduct research related to the development of software such methods can be used to process and analyze the MEQ data. In this case I do research related to software development related to the timing of arrival using the spectrogram. After the location of the hypocenter is obtained, then the next step is to analyze the moment tensor and tomography. From the various analyzes performed, the determination of the fracture zone in the Geothermal area can be done well. It is expected that this study provides the best results so the methods can applied in the determination of a more precise fracture zone.
"
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2014
T43256
UI - Tesis Membership  Universitas Indonesia Library
cover
Mazytha Kinanti Rachmania
"Penelitian ini berfokus pada keanekaragaman taksonomi Class Ktedonobacteria, kemampuannya sebagai penghasil enzim, deskripsi takson baru, dan analisis whole genome. Tujuh belas isolat diperoleh dari sampel tanah di hutan dekat geyser, kawasan geotermal Cisolok, Jawa Barat. Sequence gen 16S rRNA dari semua isolat dibandingkan dengan spesies terdekat pada database EzBioCloud. Seluruh isolat memiliki nilai homologi yang rendah terhadap Dictyobacter aurantiacus S-27T (97,82-98,18%). Penapisan kemampuan enzimatik menunjukkan bahwa sebagian besar isolat (88,23%) menghasilkan amilase dan selulase. Komposisi bakteri dari enam sampel dianalisis dengan metode metabarcoding gen 16S rRNA pada daerah V1-V3 menggunakan Illumina Mi-Seq Next Generation Sequencing. Ktedonobacteria merupakan kelas yang paling mendominasi dalam Phylum Chloroflexota (17,74-89,49%) pada lima sampel; Namun, kelas tersebut tidak terdeteksi pada satu sampel (tanah di bawah batu besar). Empat puluh tujuh amplikon gen 16S rRNA dari taksa terdekat Ktedonobacteria berhasil diperoleh dari enam sampel yang mewakili garis keturunan baru pada tingkat takson yang tinggi. Strain S3.2.2.5 diisolasi dari tanah di dalam serasah batang bambu. Karakter fenotipik, genotipik, dan filogenetik menunjukkan bahwa strain tersebut mewakili spesies berbeda dari Genus Dictyobacter; sehingga diusulkan spesies baru Dictyobacter halimunensis sp. nov.

This study focuses on the taxonomic diversity of the class Ktedonobacteria, their ability as enzyme producers, description of novel taxon, and whole genome analysis. Seventeen isolates were obtained from soil samples in the forest near geyser, Cisolok geothermal area, West Java. The 16S rRNA gene sequence of all isolates was compared with all related species in the EzBioCloud database. All isolates had low similarity values to Dictyobacter aurantiacus S-27T (97.82-98.18%). Primary screening of enzymatic abilities showed that most isolates (88.23%) were amylase- and cellulase-producing Ktedonobacteria. Bacterial composition analyses from six samples were performed based on the V1-V3 of 16S rRNA gene metabarcoding using Illumina Mi-Seq Next Generation Sequencing. Ktedonobacteria was the most dominating class within the phylum Chloroflexota (17.74-89.49%) in five samples; however, it was not detected in one sample (the soil under a big rock). Forty-seven 16S rRNA gene amplicons of Ktedonobacteria-related taxa were generated from six samples and represented the putative new lineages in high taxonomic rank. A strain S3.2.2.5 was isolated from soil inside a decayed bamboo stem. The phenotypic, genotypic, and phylogenetic data suggest this strain represents a distinct species of the Dictyobacter genera; hence, a new species, Dictyobacter halimunensis sp. nov. is proposed."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Universitas Indonesia, 2022
D-pdf
UI - Disertasi Membership  Universitas Indonesia Library
cover
Syawalman
"ABSTRAK
Pipa API 5L Grade B adalah pipa yang digunakan sebagai penyalur pada industri minyak (BBM), gas dan industri kimia. Pengujian dibatasi oleh medium air hujan, air pantai dan air laut tengah di daerah Tanjung Priok. Sampel pipa diuji kekuatan mekanisnya (uji tarik) untuk mengetahui nilai tensile strength, menggunakan standar ASTM E8. Kemudian dilakukan pengujian Mikroskop Optik dan SEM untuk mengetahui struktur mikro. Analisa fasa dan struktur kristalnya dilakukan dengan pengujian XRD. Pengujian laju korosi menggunakan metode polarisasi potensiodinamik G102-99. Terhadap pipa bekas pakai yang sudah terkorosi di area tersebut, dilakukan pengujian Mikroskop Optik, XRD, SEM dan EDX untuk melihat struktur mikro dan komposisi kimia senyawa produk korosi yang terbentuk. Hasil penelitian menunjukkan terjadinya korosi merata, korosi batas butir, korosi celah dan korosi sumuran. Laju korosi paling besar terjadi di lingkungan pantai, yaitu sebesar 2.29 mpy, di laut dalam 1.96 mpy dan laju korosi paling rendah terjadi oleh air hujan, sebesar 0,45 mpy. Hal ini disebabkan karena di lingkungan pantai salinitas dan kandungan zat padat yang terlarut lebih tinggi.

ABSTRACT
The pipe API5L Grade B is the pipe used as distributors for oil industries , gas and chemical industries. The test is limited by the medium of rain water, coastal water and middle sea water in Tanjung Priok. The pipe sampling is tested for mechanism strength to get tensile strength value by using the standard of ASTM E 8. The test then continued to optical microscope test and scanning electron microscopy (SEM) to get the micro structure orientation. The phase and crystal structure analysis was carried by x-rays diffraction (XRD) test. The analysis of corrosion accelerator was carried by the metod of potentiodynamic polarization G102-99. The corroded used pipe in the area then had optical microscopy tests, XRD, SEM and EDX to get the microstructure and chemical composition of the corrosion products compound formed. The test result shows the occurance of prevalent corrosions, intergranular corrosions, crevice corrosions and pitting corrosions. The biggest corrosions accelerated in the coastal water area wich about 2.29 mpy, in the dept sea for about 1.96 mpy and the lowest is in the area of rain water with 0.45 mpy. This is due to the salinity of the coastal area and the content of dissolved solid is higher.
"
Depok: Universitas Indonesia, 2016
T45279
UI - Tesis Membership  Universitas Indonesia Library
cover
Dandi Baskoro Soebakir
"Keberadaan struktur geologi merupakan salah satu parameter penting dalam menentukan zona permeabel pada suatu sistem geotermal. Penelitian ini dilakukan di salah satu area prospek geotermal di zona Sistem Sesar Sumatera (GSF) yang termasuk dalam segmen Angkola dan Barumun yang bertujuan untuk mengidentifikasi kemenerusan fitur permukaan hingga bawah permukaan terutama struktur geologi yang berkaitan erat dengan zona permeabel dengan mengintegrasikan data geologi, geokimia, dan geofisika. Teknologi remote sensing digunakan untuk mengidentifikasi struktur geologi yang terobservasi di permukaan yang dikorelasikan dengan persebaran manifestasi permukaan. Namun, tidak semua struktur geologi yang terobservasi di permukaan dapat diamati dan kemenerusannya dari permukaan hingga bawah permukaan dilakukan dengan pendekatan geofisika menggunakan data magnetotelurik (MT) dan gravitasi. Interpretasi struktur geologi permukaan berdasarkan analisis remote sensing dan persebaran manifestasi permukaan memiliki korelasi yang positif dengan hasil gravitasi adanya struktur graben dari zona GSF yang memiliki orientasi baratlaut-tenggara. Kelurusan dan karakteristik (arah dan kemiringan) struktur ditandai dengan adanya kontras nilai gravitasi, nilai Horizontal Gradient Magnitude (HGM) maksimum, dan nilai zero Second Vertical Derivative (SVD) serta analisis Multi Scale-Second Vertical Derivative (MS-SVD). Hasil interpretasi struktur bawah permukaan gravitasi berkorelasi positif dengan analisis parameter MT (splitting curve MT) yang dapat mengindikasi zona struktur bawah permukaan. Gabungan interpretasi struktur permukaan dan bawah permukaan teridentifikasi adanya 5 struktur (F1, F2, F3, F4, dan F5) yang diklasifikasikan sebagai Struktur Pasti (F1, F2, F3, dan F4) dan Struktur Diperkirakan (F5) yang memiliki orientasi baratlaut-tenggara. Struktur F3 yang berorientasi baratlaut-tenggara merupakan struktur utama yang berperan sebagai fluid conduit (zona permeabel) yang dibuktikan dengan adanya manifestasi mata airpanas bertipe klorida. Berdasarkan hasil pemodelan inversi 3-D MT dan pemodelan kedepan 2-D gravitasi dapat mendelineasi zona reservoir pada kedalaman 1500 – 2000-meter yang dikontrol oleh struktur F3 dan zona reservoir berasosiasi dengan batuan metasediment yang nantinya dapat menentukan lokasi sumur pengeboran. Untuk memvisualisasikan sistem geotermal secara komprehensif, maka dikembangkan model konseptual dengan mengintegrasikan model geofisika yang memiliki kualitas data optimum dengan data geologi dan geokimia yang saling berkorelasi, sehingga dapat dijadikan dasar dan acuan dalam menentukan lokasi pengembangan sumur produksi dan reinjeksi dan menurunkan resiko kegagalan dalam well targeting.

The existence of geological structures is one of the important parameters in determining the permeability zone in a geothermal system. This study was conducted in one of the geothermal prospect areas in the Sumatera Fault System (GSF) zone included in the Angkola and Barumun segments which aims to identify the continuity of surface to subsurface features, especially geological structures that are closely related to permeability zones by integrating geological, geochemical, and geophysical data. Remote sensing technology is used to identify geological structures observed at the surface that are correlated with the distribution of surface manifestations. However, not all surface-observed geological structures can be observed and their continuity from the surface to the subsurface is done with a geophysical approach using magnetotelluric (MT) and gravity data. Interpretation of surface geological structures based on remote sensing analysis and the distribution of surface manifestations has a positive correlation with the gravity results of the graben structure of the GSF zone which has a northwest-southeast orientation. The alignment and characteristics (direction and slope) of the structure are characterized by the contrast of gravity values, maximum Horizontal Gradient Magnitude (HGM) values, and zero Second Vertical Derivative (SVD) values as well as Multi Scale-Second Vertical Derivative (MS-SVD) analysis. The results of gravity subsurface structure interpretation are positively correlated with MT parameter analysis (splitting curve) which can indicate subsurface structure zones. The combined interpretation of surface and subsurface structures identified 5 structures (F1, F2, F3, F4, and F5) classified as Certain Structures (F1, F2, F3, and F4) and Estimated Structure (F5) that have a northwest-southeast orientation. The northwest-southeast oriented F3 structure is the main structure that acts as a fluid conduit (permeability zone) as evidenced by the manifestation of chloride-type hot springs. Based on the results of 3-D MT inversion modeling and 2-D gravity forward modeling, it can delineate the reservoir zone at a depth of 1500 - 200 meters controlled by the F3 structure and the reservoir zone is associated with metasedimentary rocks which can later determine the location of drilling wells. To visualize the geothermal system comprehensively, a conceptual model was developed by integrating geophysical models that have optimum data quality with geological and geochemical data that are correlated, so that it can be used as a basis and guide in determining the location of production well development and reinjection and reduce the risk of failure in drilling targets."
Jakarta: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2023
T-pdf
UI - Tesis Membership  Universitas Indonesia Library
cover
Riene Kaelamanda Pragitta
"Korosi seragam dan pitting internal pada pipa sumur panas bumi umum terjadi karena fluida mengandung medium korosif garam dan CO2. Ketika terdapat gas CO2 yang terlarut dalam air, maka akan menyebabkan terjadinya korosi sweet. Garam cenderung terdisosiasi menjadi ion yang menyebabkan peningkatan konduktivitas listrik. Semakin tinggi konduktivitas, maka semakin tinggi kemampuan air garam untuk membawa arus listrik pada permukaan logam antara daerah anodik dan katodik, sehingga menghasilkan laju korosi yang lebih tinggi. Baja karbon AISI 4140 banyak digunakan sebagai material untuk pipa sumur panas bumi. Dalam penelitian ini, akan dilakukan analisis korosi baja karbon AISI 4140 di lingkungan dengan kadar garam tinggi yaitu 40950 mg/L NaCl + 5960 mg/L KCl + 2664 mg/L CaCl2. Pada tiap pengujian dilakukan dua variasi, yaitu dengan injeksi CO2 dan tanpa injeksi CO2. Berdasarkan hasil analis karakterisasi XRD, terdapat fasa Fe pada semua sampel dengan jenis larutan dengan dan tanpa injeksi CO2, namun pada sampel dengan larutan injeksi CO2 memiliki intensitas yang lebih kecil. Rendahnya intensitas fasa Fe mengindikasikan adanya deposit di permukaan sampel. Hasil analisis uji korosi menggunakan metode hilang berat menunjukan sampel yang dilakukan peredaman dalam larutan dengan injeksi CO2 menghasilkan penurunan massa yang lebih besar dibanding sampel yang diredam dalam larutan tanpa injeksi CO2. Hal ini didukung dengan laju korosi baja AISI 4140 pada larutan dengan injeksi CO2 lebih tinggi dibandingkan tanpa injeksi CO2 pada uji cyclic voltammetry. Tingginya laju korosi baja di lingkungan CO2 adalah akibat tingginya CO2 terlarut dalam air yang membentuk senyawa H2CO3 yang dapat menurunkan pH sehingga menjadikan larutan semakin korosif.

Uniform corrosion and internal pitting of geothermal well pipes are common because the fluid contains the corrosive medium of salt and CO2. When there is CO2 dissolved in water, it will cause sweet corrosion. Salts tend to dissociate into ions causing an increase in electrical conductivity. The higher the conductivity, the higher the ability of the salt water to carry an electric current on the metal surface between the anodic and cathodic regions, resulting in a higher corrosion rate. AISI 4140 carbon steel is widely used as a material for geothermal well pipes. In this research, the corrosion analysis of AISI 4140 carbon steel will be carried out in an environment with high salt content, namely 40950 mg/L NaCl + 5960 mg/L KCl + 2664 mg/L CaCl2. In each test, two variations were performed, namely with CO2 injection and without CO2 injection. Based on the results of the XRD characterization analysis, there was a Fe phase in all samples with the type of solution with and without CO2 injection, but the sample with CO2 injection solution had a smaller intensity. The low intensity of the Fe phase indicates the presence of deposits on the sample surface. The results of the analysis of the corrosion test using the weight loss method showed that samples soaked in solution with CO2 injection resulted in a greater reduction in mass than samples soaked in solution without CO2 injection. This is supported by the corrosion rate of AISI 4140 steel in a solution with CO2 injection which is higher than without CO2 injection in the cyclic voltammetry test. The high rate of corrosion of steel in the CO2 environment is due to the high dissolved CO2 in water which forms H2CO3 compounds which can lower the pH, making the solution more corrosive."
Depok: Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Indonesia, 2022
S-pdf
UI - Skripsi Membership  Universitas Indonesia Library
cover
Arif Junaidi
"ABSTRAK
Paduan aluminium AA5083 merupakan jenis paduan aluminium yang sering digunakan untuk konstruksi badan kapal khususnya untuk kapal patroli atau kapal-kapal cepat. Untuk proses penyambungan pada konstruksi lambung kapal pada umumnya digunakan metode pengelasan gas metal arc welding (GMAW). Kekuatan hasil pengelasan sangat penting khususnya ketangguhan terhadap retakan (crack toughness), dikarenakan operational dari kapal cepat tersebut. Pada penelitian ini dilakukan pengelasan paduan aluminium AA5083 dengan ukuran 150 mm x 350 mm , dengan ketebalan 15 mm dan 20 mm. Metode pengelasan dengan gas metal arc welding dengan dua logam pengisi yang berbeda yaitu ER5183 dan ER5356 dan gas pelindung yang digunakan adalah 99% argon.
Hasil penelitian diperoleh bahwa maksimum nilai ketangguhan retak didapatkan pada pengelasan dengan material tebal 15 mm dengan logam pengisi ER5356 dan masukan panas 7.8 kj/cm.

ABSTRACT
Aluminium alloys AA5083 is alloys which mostly used in the hull components of ship and high speed craft. Normally gas metal arc welding (GMAW) are used for joining the construction. Welding strength especially crack toughness is very important on this welding due to normal operation of the ship or high speed craft. On this research welding of aluminium alloys AA5083 with dimension 150 mm x 350 mm and thickness 15 mm and 20 mm, were carried out by gas metal arc welding method using two difference filler metal ER5183 and ER5356, and 99% argon are used as shielding gas.
The result of experiment that the maximum value of crack toughness was shown on welding with thickness plate 15 mm using filler metal ER5356 and heat input 7.8 kj/cm."
2015
T44354
UI - Tesis Membership  Universitas Indonesia Library
cover
Brahmantia Brava Prajitno
"Inhibisi merupakan salah satu metode penghambatan laju korosi, salah satu jenis dari inhibitor adalah inhibitor organik yang memiliki sifat biodegradable sehingga bersifat lebih ramah lingkungandan relatif lebih murah dibandingkan inhibitor anorganik.Penelitian ini dilakukan untuk mempelajari perilaku inhibisi dari campuran ekstrak melinjo dan kunyit pada pipa baja API-5L di lingkungan NaCl 3,5% dengan menggunakan metode kehilangan berat dan polarisasi.
Dalam penelitian ini variasi kadar ekstrak melinjo dan kunyit dicampur dengan berbagai kadar. Sebagai single inhibitor melinjo menghasilkan efisiensi yang lebih tinggi dari sebagian besar kadar campuran. Pada percobaan polarisasi efisiensi terbaik ada pada campuran 6 ml kedua ekstrak dengan acampuran 8 ml kedua ekstrak sebagai efisiensi kedua terbaik.

Inhibition is one of corrosion protection method, one kind of corrosion inhibitor is organic inhibitor which has biodegradable characteristic thus the inhibitor is environmental friendlier than conventional inorganic inhibitor. This research was done to study the inhibition activity of combination between melinjo and turmeric extract for API-5L steel pipe in NaCl 3,5% environment. Weight loss and polarization method were used to measure the inhibitor efficiency.
In this study concentration of melinjo extract and turmeric extract were varied.It was found that as a single inhibitor melinjo extract has more efficiency than the combination inhibitor. In polarization method it was found that the combination of 6 ml of the two extract has the highest efficiency followed by the combination of 8ml.
"
Depok: Fakultas Teknik Universitas Indonesia, 2015
S59628
UI - Skripsi Membership  Universitas Indonesia Library
<<   1 2 3 4 5 6 7 8 9 10   >>